Tuning Ford Fusion - effective methods for improving the car. What you need to know about Tuning Ford Fusion? Replacing the oil in the engine and transmission

Noise insulation Ford Fusion

Ford Fusion insulation will help turn ride on this car in a more comfortable time. Ford Fusion Noise Isolation is a very important and weighty procedure.

Thanks to the correct noise insulation, you can not only increase comfort, but also insulate the body of the car, eliminate various shortcomings (squeaks and vibrations of plastic elements), and most importantly - to increase the acoustic properties of the cabin.

That the procedure is submitted

Why do the doers pay the most attention during noise insulation?

The fact is that it is here that the speakers of the car are set for playing music. If the doors are not isolated well enough, then no qualitative sound and dream of dreaming.

The procedure for isolating the doors, in principle, does not constitute any complexity. It is for this reason that many are solved for the holding of Shumkov with their own hands, realizing that in a hundred for such services they will take big money. Money saving is not the only reason for selecting an independent installation.

No one, except the owner, will not make noise insulation better (provided that the owner of the car is endowed with the necessary knowledge). Professionals are more thinking about how to make money than to make their work qualitatively (in Russia, in Russia, it is difficult to argue with this statement).

So, below shows a step-by-step algorithm for installing noise insulating material on the door Ford Fusion.

Algorithm for installing noise insulation on the door

To begin with, we will find out what materials we need:

As an insulator of vibrations, it is recommended to use the "Shumoff 3M" material. There will be about 25 sheets, although everything depends on the size, and most importantly, the ability to work with the material. As a rule, newcomers and nonsense spend much more material than experienced masters and specialists (this should be considered);

As a noise insulator, it is recommended to take a 6-millimeter polyfoam. Approximately 6 sheets will be enough;
Be sure to acquire White Spirit, which perfectly degreases the surfaces before sizing the materials;

Construction or technical hair dryer will help heat the material to the desired temperature.

Note. By the way, a special furnace is used to warm up for warming up, in which pre-materials are obtained by the desired temperature. This saves time. Unfortunately, at home, it is almost impossible to use this method. But the hair dryer will not fail, since it quickly warms the materials to the desired temperature.

The roller is also required to be easily smoothed out the outfit sheets. It is necessary to do this so that under the material there is no air bubbles left, which will continue to negatively affect the service life of the material and its effectiveness;
You need to prepare screwdrivers, better kit in which TORX type tools (asterisk) are present;
It is also recommended to arm a set of end / outstanding keys.

With materials and tools figured out, now to the most important:

First of all, you need to remove the trim from the door. It is clear that the door must be opened to work more convenient;
Next, disconnect the cable;
Remove and dismantle the speaker, delivered at the factory (as a rule, this sound emitter cannot provide a worthy level of sound and change it to a more productive).

Note. To dismantle it is recommended to use TORKS keys (asterisks). Some bolts may not represent difficulties when unscrewed. But there are such, the work with which will give yourself to the amateur (will have to suffer, but the result is worth it).

We continue:

We must now turn off the STCPD motor;
Then completely remove the door card, the trim;
We get direct access to the inner parts of the door with which we will have to work;
We process the surface of the outer inside of the door (part of the door, which looks outside) White spirit;
We prepare the vibration insulator, cutting it on the size of the door, and then heating with a hairdryer.

Council. If it is not possible to find a technical hairdryer, you can use a soldering lamp. But it needs to act extremely gently, observing security measures!

Put the sheets of the vibration insulator on the door;
Now we take for "Shumkov". But in this case, you will not need to heal anything. The material has an adhesive layer and just remove the protective film to carry out the sizing;
We proceed with the same manner internal part of the door from the cabin;
We collect everything back, installing the trim, motor and a new speaker.

Little things solve a lot

That's what needs to be done:

The remaining vibration insulating material to process all the distressed places of the door;
Add AntiSiPrip to the zone near the mirror;
Treat the door trim (also by anti-scrip).

In principle, it's all. Video and photo - materials will help in the process of carrying out the event, will give a practical understanding of what is happening. The instruction can be supplemented with information from other sources (on our portal you will find a lot of interesting articles on the topic of noise insulation).

The price of the procedure will not be high, if working with the material neatly and economically.

The refinement of serial cars can be divided into two types: useful tuning and various styling. In the Internet market, the owner is possible to choose and buy accessories for Ford Fusion 2002-2012, it will make the car even more stylish. Any motorists will be very pleasant not only not only to stand out in the stream, but also to establish an indispensable device. Purchase tuning from leading Russian and foreign manufacturers, and your soul will admire every day with a unique and unforgettable appearance of this car.

In Russia, a giant variety of accessories for tuning Ford Fusion 2008-2011 is produced, and our customers are constantly asked: what to pay attention to first? The owner store can recommend first to consider it, without which the use of your car can not be very pleasant and easy. In the salon of any car, you must buy mats that will help avoid refurbing and keep moisture. In the car, not only there is a chance of developing rust, but there is a risk of wiring, which represents even greater danger.

The next type of main changes is to install windows and hood windows. Such tuning will protect Ford Fusion 2009-2010 from winds and chips. In the shop, there are deflectors of individual species and sizes in the catalog. For example, stainless molding deflectors: Such accessories have an excellent appearance.

Installation of body kit in Moscow

The main direction of the Ford Fusion tuning, which offers our store, is the sale of steel stuff and aluminum thresholds. Car footrests can help when landing in the cabin and make the use of cars more comfortable. Without the foothold, children and people of older will be difficult not to stain clothes and shoes, without them it is inconvenient to clean the roof of snow or put cycling fasteners.

Practical stainless steel kit will help protect bumpers and car doors from colliding with traffic neighbors and from other damage. Many small collisions will pass imperceptibly with the help of powerful assembly and thick steel. Similar tuning for Ford Fusion is vital when moving in bad roads or in conditions of closeness of a modern major city with a large number of cars.

The owner store boasts a huge number of different accessories for tuning salon and the appearance of cars. Various linings on mirrors, spare wheel boxes and spoilers. Any such accessory will make the appearance of a modern car more stylish and attractive. Our tuning you can install yourself or in our service center on the day of purchase. We will deliver goods for tuning in Moscow by courier or anywhere in the Russian Federation logistics companies: it is quick and reliably.

Read 5 min.

Ford Fusion - urban subcompactvan, which is great for domestic needs and realities. The main differences, which conquered the popularity model in the domestic automotive market, can be called a small price and high clearance. In terms of demand for Auto Fusion, confidently held second place among Ford cars after focus. Even the name Ford Fusion, the developers emphasized the idea of \u200b\u200bthe "merger" of the qualities of the Golf Class hatchback and the "parquet" SUV. It suggests that the conclusion suggests that to improve the car, increasing those or other functions and forms, in two directions. Ford Fusion, like other models of the brand, is quite good to tuning. This concerns both the functional component and exterior. The availability of parts, especially for an external upgrade, as well as simplicity of their use allows you to produce high-quality Tuning Ford Fusion with your own hands even inexperienced novice masters and car owners. The most common improvements in the model that can be performed with your own hands are:

engine chip-tuning;
optics improvement;
improvement of the brake system;
improving clearance;
adding external elements as aesthetic content and with a functional load.

Engine

Obviously, the real tuning implies real functional changes in the car's power unit. At the same time, it is clear that 99% of the owners of Ford Fusion will do such a hand. And most importantly, and do not need. It is enough to improve the management of the operation of the power system. High-quality influence on the electronic system controlling and responsible for the operation of the engine, the so-called chip tuning may have a stunning complex effect. The result of such an intervention can be:

increase engine power without mechanical impact;
improving car dynamics;
the best response to the actions of the driver;
reducing fuel consumption.

In the presence of the necessary equipment, armed with skillful hands and detailed instructions, tuning the firmware of the control unit is quite real and their own hands. Of course, in this case, all responsibility for possible failures, malfunctions, incorrectly installed or configured firmware falls on the shoulders of the Ford Fusion owner. If the procedure is carried out in a specialized service, the probability of problems is reduced, and the demand is obviously with whom.

Optics

Important in the car have lighting devices. The technology of their manufacture does not stand still, and all the time develops. New ways of illumination appear, which are much more comfortable, more economically more productive. In addition, optics can improve not only in the functional direction, but also from aesthetic considerations. To do this, you can use as standard model products, in abundance presented in the auto parts market for Ford Fusion. In addition, fighting on forums, autosites or showing a fantasy, you can improve the headlights of the car and do it yourself. Such tuning will be the most original and give the machine of individuality. For example, modular headlights are very popular, which can be given almost any shape and build lighting the most convenient and presentable way. The part is made of fiberglass, which is easy to give the desired outlines. In addition, thanks to a large manifold on the market, you can choose xenon, halogen or LED lights to taste the Ford Fusion owner, which has conceived tuning.

Brake system

The most common tuning of the Ford Fusion brake system. Which can be mastered with their own hands - replacing the drum rear brake mechanisms to disk. After that the braking process becomes more devoted and rosary. Brakes work softer and have a larger dosing range of effort. Especially superiority is noticeable on bad roads or in mountainous areas when driving through serpents. Such an improvement allows you to be significantly more maneuverable, since braking management is much higher than with native rear drum brakes.

Clearance

In principle, the clearance of Ford Fusion and by itself is the dignity of the car, since, as opposed to many other models, it is really high, which allows the car to have much greater permeability, in comparison, for example, with focus. Even regular 15-18 cm allow Ford Fusion to overcome significant obstacles. However, if such indicators do not satisfy the driver, you can try it to increase it with special tight spacers. Such tuning is available with your own hands. However, it should be understood that an increase in the road lumen may worsen the stability and controllability of the car on the road. In addition, the height of the clearance may also depend on the loading of the car, the size of the tires and wheels, depreciation wear and springs and other factors.

The site catalog The site contains all the necessary information for those who want to do fusion fusion repair with their own hands. Photo reports, articles, video, instructions, tips and recommendations will help the repair and operation of Ford Fusion. If the desired material was still not found, it is very likely that it will appear soon. Or you can ask the question of interest Community drivers and auto mechanics in the section "Questions / Answers." Thus, the repair and operation guide Ford Fusion has a worthy of the 21st century an alternative in the form of a portal site.

The site's pages are contained by many useful instructions, such as periodic procedures: and for Ford Fusion. Or - or the replacement of glass - not a single driver is insured. Of course, there are such procedures that are not so easy to do - or replace the bearing, this example. But even in this case, it is better to have a breaking about how they occur.

Brief Review Ford Fusion

The Ford Fusion starts its history already in the 21st century. In 2002, if more precisely. The car itself is their name (alloy, merger - English) emphasizes what they wanted to embody developers - a cocktail from the SUV and Hatchback Golf Class.

How well they succeeded, it can be judged by the popularity of sales - among Ford cars in Russia, Fusion inferior only focusFollowing him at the honorable second place. What was so lucked by the Russians fusion? Yes, with its pragmaticity - an excellent price / quality ratio, high clearance, a spacious luggage compartment (337 liters).

At the same time, the car was supplied in three sets:

Core;
Trend;
Elegance.

If the first was a basic set, then the second and third has already significantly expanded the complete set, adding alloy wheels, the body's "metallic", rain sensors, lights, parking, seats and windshield, air conditioning, power windows, and others, in general That is not obligatory, but comfortable things.

As for engines, then in Russia, were presented 1.4 and 1.6 Variants of Duratec TDCI, both diesel and gasoline camp. A 5-step manual box or 5-speed robotic (except gasoline 1.6) PPC was installed on everything. On the gasoline engine 1.6 there were also options with automatic transmission.

Despite its 14 years, Ford Fusion has only one generation and one restyling, which took place in 2005. Restayl introduced change in the outer view of the instrument panel, bumpers, moldings and headlights.

Despite all the advantages of this car, he is not immune from breakdown. Therefore, the Virtual Repair and Operation Guide Ford Fusion, which provides our site, can be very useful to the owners of the car, preferring to make repairs with their own hands.

Tuning Ford fusion with your own hands Complete task. At some point, any driver of the car concludes that his fusion needs tuning. To do this, you have to search for the desired parts, components and accessories. The market provides a large variety of conceivable and unthinkable new products, among which any newcomer in tuning is lost, it is difficult for him to choose from this manifold the necessary thing that can successfully upgrade his car.
In order for you to be in a similar situation, you need to familiarize yourself with the most necessary accessories for the Ford Fusion tuning.

For decorative salon decoration, the lining, imitating the tree, are highly popular. They reflect the interior of the cabin, add solidity, which is characteristic of a high-level car. To install decorative lining, you first need to degrease the surface to which the pad will be installed, and then warm this surface with a hairdryer.
In order to avoid engine damage, and other aggregates located in the Ford Fusion engine compartment, it is proposed to protect from steel. It is equipped with stiffeners, has special mounting mounts for this car model and painted in black.

Tuning Ford Fusion is easy to perform even because in car salons, there is a large number of different decorative linings. It is well in demand among them overlays on door gesthers, ornamental lining for mirrors, for gas tank rack, moldings, on door handles, a decorative plank for the trunk cover above the number. All these accessories are simple enough.

Often during the operation of the car on its inner thresholds there are damage. The landing and disembarkation of passengers is also reflected in the appearance of the thresholds, scratches appear on them, sometimes paints are possible. Repair of the above-described small, but very unpleasant damage is quite expensive, because to remove the small chip paint on the surface you have to repaint the entire surface, and this is expensive. Much cheaper to protect the thresholds from these damage with lining. They are attached on the inner surface of the threshold with the help of two-way tape, which is included with the lining. On the front lining there is an inscription car model.

Constantly used by any motorist thing is the ignition keys. Intensive work spoils their appearance very much. And modern smart keys are especially affected, as they can fail from obtaining scratches or fall, which will definitely entail expensive repairs or replace them. In order not to happen such an unpleasant for motorist of the incident, the keycases made from high-quality genuine leather should be used. Each such a cover is individually made under a specific key, taking into account the geometric shape and sizes, placement of control buttons for signaling, opening and closing doors.

In this way. tuning Ford fusion with your own hands You can completely perform without resorting to the services of car services.