Clicks steering rack when turning. Scripping and extraneous sounds when turning the steering wheel - find out possible causes. Foreign brand does not guarantee the absence of breakdowns

the main / Engine

Outsided sounds in the steering system may indicate its malfunction. Moreover, it is often possible to determine the type of failure in the nature of the sound. Therefore, we propose to further familiarize yourself with all possible fault options, their symptoms and elimination methods.

1 What to do if the hum of the steering hydraulic power is heard

Often, motorists complain about the hum of the hydraulic cylinder when turning the steering wheel left or right when the car is worth it. If the hum is quiet, then there is nothing terrible in it. It can be said that a small noise is a kind of feature of the power steering, which is found on many cars. If the hum is uneven, i.e. It is periodically enhanced, clearly heard in motion, sometimes turns into a gnage, it means that problems arose in the steering system. First of all, you should check the level of fluid in the expansion tank, which is under the hood and, if necessary, pour it. If, after an attractive sound, the sound appeared again, and the fluid level in the tank fell again, which means that there is a leak of fluid that requires immediate elimination.

First you need to learn to hear and distinguish the "bad" hum and sound from simple sounds.

If the sound is not associated with a low level of fluid, it is possible that the parts of the hydraulicel may fail. In this case, you must immediately contact the service center, since the repair of this node is quite complicated, requiring experience and knowledge. Often the owners of cars with GUR face a whistle of the steering system. At first it happens to be unset, and it appears only when the steering wheel turns until it stops. Over time, the whistle is enhanced and appears in any positions of the steering wheel, especially if the car is not heated. The reason for this whistles is the pump drive belt GUR. To get rid of the whistle, the belt must be replaced or simply adjust its tension.

Often, the whistle Gur appears after a while after replacing the belt. Therefore, try to monitor its tension until the belt is "runs up." I must say that the belt whistle can be confused with the whistle of wheel bearings. If the whistle stops when the car stops, it means that bearings whistle.

2 Screensions when rotating the steering wheel - what is the reason?

The reasons for which the steering wheel crepts during rotation may be several. Most often, the steering rail is to blame. Moreover, it can also creak for various reasons:

the anthers of tips were worn out, as a result of which the dirt was hammered;
the mechanism weakened, so it began to contact the case. Such a malfunction is usually accompanied not only by the creak, but also increased steering wheel well;
deformed rails;
steering tips come into contact with rods when turning.

With the appearance of a violin, the rail must immediately contact the specialists who accurately establish his cause and eliminate the breakdown. As a rule, the details of the steering rack are not subject to repair, but simply change. This leads to great costs, but it is impossible to delay with repair. If the rack malfunctions are not identified, the brake system should be paid. Often it is the cause of squeaks.

Less frequently creak occurs due to malfunction in the steering column, in which case it has a surface character and is clearly heard in the cabin. In addition, such syligations are accompanied by the vibration of the steering wheel, which is also impossible not to notice. Most often, the creaking in the steering column arises due to its deformation. Sometimes extraneous noises cause worm mechanism. If the creaking or "scroll" is heard right in the cabin in the area of \u200b\u200bthe steering wheel, it means that the steering wheel itself is used, which when moving hits the trim column. Nothing terrible in this, of course, no. But the syligations can deliver discomfort in the car passengers and the driver.

3 What knocks and crushes when turning - a ball or shock absorber?

The reasons for which knocks can appear, there are also several. Some of them are relatively "harmless", others require the urgent repair of the car. The latter refers to the knock of the ball support. True, this element applies not to the steering system, but to the front suspension, but since both nodes are interrelated, consider it too.

The balls of the ball usually are clearly audible on small bumps and when driving on the gravel road surface. When the car is moving along a flat road, the ball usually creaks, but may also tapping if its condition is completely delegal. To make sure the ball faults, you can enter a lubricant with a syringe into a ball finger, punctures with a needle rubber boot. As a result, the knock must stop for a slight time. Also, the symptom of the wear of the ball is the transverse backlash.

If you do not replace the ball on time, the finger can snatch out of the housing, as a result of which the wheel will simply turn out. If the ball pulls out at speeds, the car usually turns over. True, as practice shows, most often this situation occurs when moving at low speed. But, as they say, you should not tempt fate.

Another common cause of the knocks is the wear or lack of a shruss lubricant, which is only available in front-wheel drive or all-wheel drive vehicles. Sometimes, for the same reason, the crunch is heard, especially when the car enters the rotation, and the load falls on the wheel with a problem clearance. In this case, it is necessary, first of all, make sure the integrity of the anther. Often, the crackle is associated with the fall of the dirt. Otherwise, a change in a shrus is necessary.

Also, the knock may be associated with the wear of the steering tips. Usually it is accompanied by a creak when turning the steering wheel. At the same time, the knock itself is distributed only at the very beginning of turning. To make sure that the problem lies in the tips, try to shove the steering wheel from the side to the side when the car stands still. If a click is heard at each turn to the left or right, then there can be no doubt. As in the case of a screen, first of all, it is necessary to check the lubricant in the hinge mechanisms. If the backlash is also detected besides the knock, the tips must be changed.

If the knock is heard on the bumps, as well as when the car is destroyed in turn, it can be associated with the wear of the shock absorber. In this case, the stronger the load on the wheel when turning, the stronger the knock is heard. Since the left and right wheels shock absorbers are extremely rarely out of the order, clicks are heard only when you turn one way.

That's all the main causes of the noise of the steering system. If you failed to accurately determine the cause of noise, immediately make the car diagnostics in the service center. After all, steering is one of the most responsible systems responsible for security!

At the first stage of the possession of personal vehicles, the owner focuses mainly on the road situation. Over time, it comes to understanding those or other features of their car. The possibility of self-diagnostics of the vehicle breakdown appears (a knock appeared when the steering wheel is rotated, for example).

Self-diagnosis: to master it is easy

This comes, of course, not immediately, however, with the acquisition of the experience, a person who has a minimal teaching technique may well determine a number of full-time breakdowns of his car. To some extent, the skill of self-diagnosis was also due to the high cost of maintenance, and sometimes the incompetence of specialized personnel on a hundred.

What is characteristic, the ability to correctly define the vehicle breakdown will be useful to you in any case, regardless of the selected car. First of all, it suffers - most often because of bad roads. We will try to deal with the reasons for the rapid wear of the chassis from the current marks today. We describe the possible options for their breakdowns, learn to diagnose in symptoms (knocking in the steering wheel when turning, for example), as well as consider options for the rapid and prevention of their "iron horses".

Domestic - does not mean bad

It is not a secret for anyone that today the most popular cars are the so-called consumer-class cars. A rather large segment of sales in this sector occupies a domestic auto industry. As a rule, the consumer who bought such a car is guided by the available pricing policy of the manufacturer with almost world standards of quality. And so we are more and more on our streets we see new "frets", in which you will not even know the features familiar since childhood.

In the new "Granda", "Priors" and "Viburnum" are embodied almost all modern innovations available for cars of such a modest class. However, are they reliable? The last generation of vases, the famous "eights", "nine" and "dozens" quite often lost in reliability and fitness to our roads, even foreign cars of the old sample. They still bought due to a modest price, but still considered more as a temporary component of their lives, hoping in the near future to transfer to more comfortable and reliable cars of Western or Asian production.

As already noted, most often in modern road realities fails. Is it reliable in modern vases? The answer is unequivocal: yes. Engineers and designers tried to ease the life of the modern driver.

Repair - it's expensive

However, the use of innovation and an increase in reliability have the opposite side of the medal. Modern mechanisms are much more difficult to repair (and it is not only about technology, but also about money). And although the repair of the "chassis" of the vase, of course, cannot be compared with the repair of a similar Western product, but there is no trace from the past cheaply.

Based on this sad fact, the financial risks of the modern driver who chooses the product of the domestic producer or imported car, differ noticeably. Therefore, the value of the auto diagnostics of auto faults has significantly increased, at least as common as the knock in the steering wheel when turning.

Knocking in the steering wheel - what to do?

Believe me if you clearly define what is faulty in your car, you will spend much less money for a hundred. Cause Banalna: Do not have to pay for what you do not need (but what can try to impose on a hundred).

So, consider the situation. You went to the sea (in the mountains, for the city - not the essence important) and heard a knock when you turn the steering wheel ("Priora" your relatively new!) Do not rush to go to the service right away. Try to deal with the problem yourself. A set of regular and not full-time situations for such damage is quite limited.

Consider the main options. The most frequent critical situations are associated with the steering mechanism. The first thing to determine is the character of the knock. It happens "plastic" and "metallic."

Plastic protection loosened

If with a sharp turn of the steering wheel, the knock is similar to the friction of plastics, almost 100% with the car is fine. As a rule, such sounds make up badly fitted wing protection. When the front wheels are twisted, we are very often taking up and slightly deform the plastic locker. It is he who makes such unpleasant, but rather safe sounds.

However, it is not worth not paying attention to this. The fact is that plastic protection is attached directly to the "skirt" of the front bumper. And if it is completely deformed, it is possible that one day at the next turn you just snatch it (and at the same time damage the bumper). Therefore, it is better not to hope for "Avos", but to fit the defense.

When the parts are replaced

The situation is much more serious if the knock at the rotation of the steering wheel is more like a metal cracking or grinding. This means that in the near future you will have substantial financial expenses. And in order to cut them, it is necessary to sort out the reasons yourself.

When the "bullous" knock appears when the steering wheel is rotated, the simplest explanation of this is the wear of the tip of the steering. Quite unpleasant, requiring attention phenomenon. After all, if the wear process continues, failure of the entire steering mechanism is possible, and as a result - expensive repair, and maybe even an emergency on the road. The repair is not very expensive, although the tips usually change in a pair - on both sides of the car. The main difficulty lies in subsequent workflow work.

Another rather frequent problem when a knock appears when the steering wheel is turned ("Kalina or Priora" is subject to this "sore), is associated with the wear of the bearing of the upper support of the shock absorbing rack. The disease is unpleasant, but quite easily eliminated. The bearing itself is not very expensive, and work on its replace will not take a long time.

From the burst springs before replacing shock absorbers

A rather unpleasant knock when turning the steering wheel is made of burst springs. Repair is associated with the analysis and, as a result, a possible replacement for the same bearing of the top support. It should be noted that in case of incorrect diagnostics or other reasons why you cannot carry out this repair, the consequences will be very serious for you. The burst spring will not be able to take over the part of the load, which it is experiencing during the vertical roll of the car. In this regard, there is an additional impact on what can lead it to breakage. But this is already full repair of the front running of your car. It is not difficult to calculate financial losses in this case. You will have to buy not only new springs, but also new shock absorbers, which in most cases are changing pars.

If a knock when turning the steering wheel to the right or left is also accompanied by a hum, this is a direct consequence of the failure of the bearing of the front wheel hub. Sad. The complexity of the repair is to extract the old bearing from the hub (a very long and expensive operation). Such a breakdown may be "lethal" for all front and all-wheel drive cars. In the case of complete wear of the hub bearing, the destruction of the front suspension is possible and - do not give, God, of course! - Emergency situation on the road.

How to diagnose a shrus wear

Let us turn to the main and most serious noise that you can hear: a knock when you turn the steering wheel ("Kalina" or "prior" - no matter) in one direction or another. Metal cracking with the full turn of the steering wheel indicates the failure of a shruss or, as it is also called in the people, "grenades". When the crash is distributed and right, and on the left, this means that both of your "grenades" are subject to replacement. If, when you turn the steering wheel to the left, the knock is distributed from the same side, you know exactly what the item is more worn.

The situation with the failure of the scruses is usually associated with the damage of the rubber anther, which protects the metal case of this mechanism. Even a small gap can lead to a replacement of one of the most expensive nodes in the running machine. Therefore, once a month it is better to check the anthers of both "grenades" for damage.

Monthly prophylaxis of noise appearance

Noise and cods on vases may arise due to the weakening of numerous threaded connections. These are easily inflicted moments and as easy-to-wear. The main thing is not to panic, but to call on a good lift or "pit" in the garage. Then, armed with a wrench of the desired size, simply pull out all the speaking and knocking connections, including the wheels of your car.

Foreign brand does not guarantee the absence of breakdowns

The situations described above are typical not only for Russian cars. In principle, the expensive foreign car is not insured. The whole question is, with what frequency it will happen.

As already noted, the quality of cars produced in Russia significantly improved. This applies to both truly Russian vases and cars produced by our license. The percentage of factory marriage is significantly reduced: a knock when turning the steering wheel ("Logan", for example, going to Russia) will not immediately. And avoiding such situations is quite possible. Experts advise once every six months to undergo the necessary diagnostics on specialized hundred, not bringing to the notorious "knocks and cods" in the chassis.

In addition, considering not always high-quality road surface, it is necessary to comply with the high-speed mode and take security measures for the intersection of complex or just bad sites. If these simple recommendations will be observed, your car will serve you for many years without any breakdowns, and the means not spent on the repair of motor vehicles can be used for something else.

The presence of problems in the operation of the steering, as well as the failure of the brake system can entail a safety threat in the movement of the car. Application in many passenger cars of hydraulic tanks and retrofitting mechanisms allows to significantly improve the control of the machine and reduce the list of faults to a minimum.

The problem of knocking in the steering wheel can be in shock absorbers or bolts

What are the steering problems?

Practice shows that the most common and characteristic malfunction is the wear of the ball joints of the tips of the steering.

But other problems exist in addition to this:

Development (wear) of the elements of the rush mechanism.
Disorders of the tightness of the compounds, hoses and systems in general.
Wear or defects of steering shaft bearings.

In cars that are equipped with a power steering, there may also be problems in GUR:

Clogging system.
Destruction or wear bearing shaft of a paddle pump.
Disrupting the tightness of the compounds and hoses.
Weak tension of the drive belt.
Low or oil leakage in the expansion tank.

Pretty frequent car problem, when when turned the steering wheel, a knock, a click or crunch is heard. It can constantly knock, and maybe only after a long parking lot. Such a nuisance can even happen from those motorists who follow the condition of the car and replace worn items on time. This symptom should take seriously and fix the breakdown as soon as possible.

On the video: knock when turning the steering wheel - Slusa or Triship - Lubricant came out

Possible causes and confusion methods

Outlooking a ball support. It must be replaced, as it can break through and the car will have to drag on the tow truck (the wheel is turned unnaturally inside or out and it will be impossible to go).
Outlooking a grenade. Moreover, when turning, the right pomegranate is loaded to the left and vice versa. Accordingly, if the knock is heard when the steering wheel is rotated to the left, we change the right grenade.
Can knock or creaking worn stabilizer bushings. The problem is solved easily: you need to sprinkle with silicone lubricant on the bushings. Rubber will become more elastic and creaking or knock will pass.
A knock may arise with a faulty or weakened steering rack.. It can give vibration in the steering wheel. It is necessary to tighten the rail mountings or to diagnose the rail to the service station, and repair or replace the spare parts.
Can weaken the engine crankcase protection bolts. Although this occurs infrequently, but not a detected problem can bring a lot of unpleasant moments. The solution is to simply tighten the bolts. If the thread of the bolt has broken, replace the bolt. You may have to update the thread.
If the knock appeared after replacing the wheel, then the possible reason for the knock will be not to the end of the tightened wheel bolts. Over time, vibration is added to the knock. The problem is solved per minute - pulling the bolts to the necessary effort.
Known can cracked or bursting spring. Unfortunately, the quality of spare parts in recent years has delivered in front of motorists and such a problem. The solution is to replace the cracked spring.
Worn or sweating shock absorbers May when turning the steering wheel to the right or to the left "beat", that is, not to keep the load and live in the weight of the car with a knock. Solution - diagnostics and replacement of the shock absorber. You can diagnose yourself. To do this, it is necessary to dramatically press on with two hands on the wing in the area of \u200b\u200bthe shock absorber and also abruptly let go. Watch not only when whether a knock appears, but how many oscillations make a car after pressing from one and on the other side.

Often, motorists operating domestic production cars face a fairly unpleasant problem characterized by the appearance of the knock at the front of the front of the vehicle at the time of the steering wheel turn. The first decision coming into the head of the motorist is the appeal to a specialized car service. However, he has several significant minuses. For example, the lack of a guarantee of a positive result or significant financial costs. That is why, we recommend trying to deal with the problem yourself.

Causes of the knock when turning the steering wheel

So, I diagnose the knock when turning the steering wheel. To do this, perform several preliminary manipulations:

Rinse the elements of the front suspension of water.
Install the vehicle on the pit or raise on the lift.
Connection sites (twists) Clear with a rigid brush.
Conduct a visual inspection of the elements of the front suspension.

The list of visual inspection needs to include the following items:

checking the fastening of the transverse stability stabilizer;
monitoring the status of supporting pillows racks;
monitoring the fastening of suspension elements;
checking the status of the silent blocks of the lever, fixing rods, stretch marks, etc.;
monitoring the state of compression buffer (for destruction) capable of generating a knock;
check the degree of wear of the hinge lever of the suspension system, the low lever connections.

The next step is to determine the source generating a hearing when the steering wheel rotation is the control of the state of the springs. As a result of "sedimentation", deformation or breakdown of the spirals, an obviously audible deaf knock appears.

Another cause of the emergence of the knock in the field of the front suspension of the vehicle can be strain or insufficient fastening of plastic protection of the car wheel arch.

Uninterrupted protection fragments at the moment of turning of the steering wheel are engaged with a boot with a boot Sls and form sounds similar to a knock. For all its insignificance, this defect requires enough operational elimination, since only in this case there is confidence that it will not cause other, more serious defects. For example, fastening the protection of the Arch directly to the "skirt" of the bumper makes it possible (bumper) damage during deformation of protection.

The presence of a characteristic, "bullous" knock at the time of rotation of the steering wheel indicates the exceedable degree of wear of the tips of the steering.

The failure to take timely measures to replace worn steering tips threatens the chain response of the performance of the performance by elements of the steering mechanism, which, in the worst case, will become an accident, in the best, are significant financial costs.

Attention! After replacing the tips of the steering, the "collapse-converge" of the wheels is performed.
Another fairly common cause of the knob of the knob is an increased wear of the bearings (top) rack of the shock absorber. Special predisposition to this disease is observed at the "Prior" and "Kalin". Solving the problem - replacement of the bearing. The positive moment of this lack in relatively small material and time spent on its elimination.
The combination of the knock and the roe, simultaneously arising with the right (left) rotation of the steering wheel, signals the loss of the functionality of the hub bearing of one of the front wheels of the vehicle. It should be noted that the failure of both bearings at the same time - the phenomenon is not rare. This is truly serious. The complexity of the repair work lies in the need to "reassess" the worn bearing from the landing place in the hub.
This diagnosis assumes not only a long, but also quite expensive "treatment", and non-timely adopted measures ends, as a rule, the complete destruction of the elements of the front suspension of the vehicle.
Video - what to do if you hear a knock when you turn
And finally, the reason that is hearing the overwhelming majority of motorists - damage to the hinge of equal angular velocities, or the silver. The wear of the element itself initiates the sound, more similar to "crackle", but damage to the anther Sls, which, in fact, leads to a premature failure of the hinge itself, "gives birth" sounds, often received for the knock. The most effective method of preventing this defect is regular (at least once a month) inspection of the state of the anther and immediate replacement in the event of discontinuities. This habit will significantly save you not only time, but also money.

Many drivers often face such a problem that clicks or knocks or knocks are heard when turning the steering wheel. This situation can occur both in old cars and new, it is quite common. Determine the source of these clicks can any driver without referring to the wizards of a hundred. It saves time and money. If the car owner has at least small skills in repair, he himself can eliminate the malfunction, spending only new spare parts.

If you click the steering wheel when you turn, and this sound is heard at each maneuver performed, it is first necessary to determine the character of the sound. If the sound is clear, the ringing, then this indicates the presence of a metal impact of metal. If the sound is less clear, muffled, then it is rather contact of metal and plastic. In addition, it is necessary to determine at least an approximate place where the sound comes from. This will not only reduce the troubleshooting zone, but also will help at least approximately determine the breakdown.

The simplest reason for clicking in the steering wheel is the wrong pressure in the wheels. If it is too different from each other, then clicks in the steering column can appear when the steering wheel is rotated. In addition, the cause can be broken downs.

If you are heard clicks in the steering wheel - check the pressure in the wheels and the state of the scenery

If the screws were bought, then the torn liner will cling to the bus and hang out, while making clicks when turning the steering wheel to the right and left.

These breakdowns are quick and easily eliminated: properly pump the wheels and fasten the shoes.

However, there are more serious reasons for the knob in the steering wheel. For example, a rather dangerous is the malfunction of the steering mechanism, then the clicks are heard directly in it. You can also check the car yourself, having arrived at the overpass and carefully examined the suspension.

First of all, the state of the steering tips is estimated. If the boot is damaged by such a tip, then the dust and sand will fall inside, as a result of which the item starts to wear quickly. And then the play is the source of clicks and a knock.
You can reveal this cause by loosening the steering thrust, for example, by mounting. If in this case a knock and backlash appears, then the tip is replaced. In addition, it is recommended to replace two tips immediately, since a small backlash appears at any tip over time. And if you replace one (put it without a backup) and leave the old (with a backlash), then the car will be nervously walk, and the noise and knock will be noticeable. In addition, it can constantly be a gathering collapse.

Checking car suspension status

Silent blocks of steering crasions can be caused by clicking. Wearing silent blocks, rubber bundle can even produce clicks when turning the steering wheel in place and during the movement. If this causes the knock, then the oscillatect blocks must be replaced.

If you click the steering wheel when you turn - check the steering tips and steering thrust

When wearing the rail sleeves, a knock can also appear in the steering wheel. A small gap is formed between the rail and gear. Sometimes it is possible to eliminate the gap using the adjusting bolt. If it did not help, the worn sleeves must be replaced.
Clicks can go from the steering rack cardan. When damaged, it can produce outsided sounds. It is just necessary to replace it.
Clicks in the suspension when turning the steering wheel can indicate a breakdown of an external shrus. Then they will occur only when turning. If clicks arise when lifting uphill, it is unfairly internal silver. Determine this breakdown is also easy: you need to drive the car on the flight and check the anthers. If they are poorly sitting, breakdowns or bleached the clamps, then the dirt got inside the shruss, and hence he failed. It is not worth tightening with the replacement, because over time the screen can be completely turned out, then the car will need to deliver to the repair point on the tow truck or towing.

Cause of clicks when turning may be faulty

If the clicks when turning are heard along with the characteristic hum of the wheels, the problem lies in the hub bearing. One of the most dangerous faults, it is better to immediately replace bearings, and if the driver is forced to move on such a car, then the speed should not exceed 80 km / h.

Additional symptoms

Causes of clicks in the steering column

Causes of clicking in the steering wheel, as we see, can be a lot. Of suspicious symptoms, the hum of wheels can be added to them, tapping, ringing, cracking, etc. In addition, it is always necessary to follow the behavior of the car itself. With a particular breakdown, the car will behave on the road not as usual. When the tip or sleeve fails, the car can "fuse". With a malfunction of a shruck, clicks, over time, will enhance everything to an unpleasant gross. The car will always show that it is faulty.

Are smallers in the steering wheel?

Depending on the origin of these clicks, the danger of the situation is determined. For example, if you arise clicks when you turn the steering wheel with the turn signal, it is not necessary to scare at all. Just the signal about the rotation makes a sound that reflects the steering wheel. But if there is a gluster, the bearing of the hub or the support of the rack, should not be slowed with the repair of the car, since the continuation of the use of such a machine leads to a deterioration of the breakage, as a result of which the accident can happen on the road.

Ways to eliminate clicks in the steering wheel

As already mentioned above, all malfunctions associated with clicks in the steering wheel can eliminate the usual driver. It is enough to determine the malfunction and or replace the broken part, or to go through it. There is nothing difficult here.
The steering wheel is one of the most important parts of the car. Any malfunctions, sounds, clicks should be immediately awarded. Steering must always be complete. Clicks in the steering wheel are a signal that a malfunction has appeared in the steering control. Therefore, do not forget about them and not pay attention to them. Take care of your car.