Means for cutting piston rings. Engine operation and repair

Daily use of a car in the conditions of the city is very serious tests and loads even for the most modern engines. Permanent switching of motion modes start-stop, operation at low-grade fuel and other consumables, the process of replacing the oil, made not by the regulations - all this can lead to the need to urgently do the engine cutting. In the car chemistry market there are special tools for let's look at what it is for substances, how to use them, as far as they are effective.

Causes of Floor Camera Details

Nagar, which is formed on and in the cylinders, does not arise in itself. There are several main reasons that lead to its formation and the need for urgent workshops. One of these is non-compliance with the car manufacturer's regulations in oil replacing issues. Some car enthusiasts for the purpose of saving are poured low-quality oils. Nagar will actively form if the motor often works in conditions of elevated temperatures due to insufficient cooling. If the engine is susceptible to overheating, quickly boils, then it is necessarily necessary for the cutting. Also, Nagar is formed through the use of low-quality additives. If the car has been standing for a long time and was not used, then before starting operation, professionals are recommended to replace the oil and use any liquid for cutting the rings. If the car is used without breaks, and the listed problems have never arose with it, then rings and other elements of the combustion chamber are locked due to the run. This usually happens after 300 thousand kilometers.

How to determine if there is a nagar on the rings and in combustion chambers

It is quite simple to determine it. There are several typical signs that talk about the problem. If in one or more combustion chambers decreased definitely talks about the focused details. Also about the need for a cutter can say increased oil consumption - approximately 300 g per 100 km. And finally, you should pay attention to the smoke from the exhaust system. It will be either white or blue. If these symptoms appear in the car, then it is necessary to urgently apply any available means for cutting the piston rings. Use a car that has a nagar in the combustion chambers is not recommended. Such exploitation will lead to a strong wear of the parts. If you do not perform the procedure for the destruction of a car on time, cracks can be formed in the cylinders. In this case, the solution to the problem will be only overhaul.

Funds for cutting the piston rings of the engine

Today there are a lot of various specialized products. The most famous is the "LAVR" cooker and the HADO products. These funds have become popular at the expense of low cost and quite decent consumer characteristics.
Selecting the tool, pay attention to how many cylinders the container is calculated. Often, such products are produced in small tubes by 10-15 ml. One such tube should only be enough for one cylinder. By purchasing a piston rings, one should also pay attention to the type of motor for which the means is suitable.

"LAVR ML-202"

This is also a fairly well-known product. The product is supplied in the form of a liquid and is intended for impact cleaning of all parts of the cylinder-piston group from Nagara. The manufacturer declares that this means for cutting the piston rings can thoroughly clean the rings and grooves. This will allow you to restore compression characteristics, as well as remove harmful deposits from the surface of the combustion chambers. Another product is able to eliminate the cylinder ignition and detonation.

The drug is produced in packages with a volume of 185 ml. This will be enough to clean the motor up to two liters from Nagara. For engines with a large volume, a package in 330 ml is offered. In fact, the "LAVR" cutter is a high quality preparation. And it is very nice because it is made entirely in Russia. Lavr ML-202 really has all those properties that are declared by the manufacturer.

How does it work

When the liquid enters the engine cylinder, a special steam cap is formed on a heating motor.
It affects deposits. Then the liquid seeps through the piston, removes the nagar. Already within one hour, the laurel rings is capable of turning the deposits into a loose formation, which easily flies out of the cylinder and then burns.

Cleaner "VinS"

This product is intended to restore compression due to dissolving and complete removal of nagar and sediments from the walls of cylinders and valves. The manufacturer reports the following characteristics: the drug is capable of restoring the mobility of the valves, and can also prevent detonation. The tool can dissolve and remove deposits from the walls of the cylinders, the grooves of piston rings. Also removed at the intake manifold. This product is an isolated piston rings. Applied using special equipment.
If you exactly follow the manufacturer's instructions, then this composition will please the result.

LIQUI MOLY OII-SCHLAMM-SPULUNG

This product clears the engine from the nagar through the lubrication system. The drug removes sludges, reduces the number of deposits on the details of the piston system. The composition is able to restore the mobility of the rings. Stated and recovery compression together with cleaning lubricants. The composition is suitable for use both on gasoline and diesel engines. In fact, such means for cutting the piston rings are nothing but an additive in
As for the effect of applying, the tests show zero results. The tests conducted did not reveal changes in the testimony of compressometers. Therefore, it can be easily concluded that this drug is ineffective.

Folk Methods

Products for cutting, which offer car enthusiasts marketers do not always have a special composition. Very often, the product is a mixture of acetone and kerosene. It can be made independently. So, mix two parts of acetone and one part of the kerosene at the rate of 150 ml per cylinder. Cased rings kerosene - a very effective way.

Engine washing fluid

Along with the means for the cutoff, there are also fluids for washing the entire engine. In each motor, during operation, a nap and resin is formed. In the process of operation of the power unit, the lubricant is oxidized and forms a film on the details of the lubricant system. Other contaminants are sticking to it. Over time, these films turn into a nagar. All this leads to wear. Especially dangerous sediments that have accumulated in reduction valves, hydrocompensators, on the oil pump grid, are particularly dangerous.
To fight these sediments, there is a special flushing of the engine "Lavr". This drug will remove all the accumulated sediments and give the motor to the second youth. There is a whole series of these funds. These liquids with different efficiency cleaned the motor from Nagara. The means must be poured into the car lubrication system. For example, washing the engine "Laurel Lux" is ideal for any types of motors. She gently and safely removes any deposit. Especially the liquid is suitable for those aggregates that were not washed for a long time.

Summary

Cutting promotes long and reliable engine operation. It is cleaning the motor from sediments and nagar, the presence of which leads to increased wear of parts and nodes. It is possible to use self-made liquids or use factory preparations that have proven themselves (for example, LavR products).