Two ways to independently install LED lighting interior in the car. Backlight of the car's interior - we make a car brighter LED backlight in auto

Flexible neon in car design

Advantages of flexible neon in its low power consumption, high strength and durability. In addition, to use flexible neon you will not need special knowledge. It is easy to cut, bend, thanks to which you can create almost any composition. Neon is easy to mount anywhere, it does not fight and does not fade.
Flexible neon is widely used for registration of the interior of the car interior:
The most important stage in the design is the selection of a combination of colors. It is necessary to carefully pick up the color gamut that is under your car. The most commonly used colors. In addition, before proceeding with the design, you need to decide on the method of illumination, you can launch neon along door circuits or torpedoes, you can create interesting compositions, ignoring the features of the bends of the cabin. It all depends on your imagination.
Lighting the salon of almost any car often does not meet the characteristic requirements, so installing flexible neon inside the cabin, you can achieve the necessary level of comfort. To do this, it is recommended to install a flexible neon on the instrument panel, door opening knobs, glove box, pedals. In addition, you can completely replace the standard backlight by installing neon.
Installing the neon cord is pretty simple. All you need is with the help of glue, consolidate the neon cord with the way you need and power it. You will also have to think about the installation of the power cord.
Consider on the example of the door backlight. To begin with, we disassemble the door, remove the trim and drill the power cord hole.

It remains only to install flexible neon under the elements of the trim.

If you wish, you can also refuse to dismantle the doors and plating, but simply glue neon along the contour, but in this case, it will hardly drink and, accordingly, will be worse protected from mechanical effects.
Similarly, the backlight is installed throughout the car's cabin.

In order to connect the power to the neon cord, use the connection scheme from the on-board network of the car or the network adapter 12V

Making your car with flexible neon, not only beauty is achieved, but also other useful properties. Flexible neon, unlike any other type of lighting, absolutely not blind and does not distract the driver. At the same time, the neon glow gives a measured rich light. In the dark you do not have to look for a handle on the door trim, you can comfortably leave the car, not afraid to hook for something. The backlight of the car increases its safety.
Thus, with the help of flexible neon, you can change the interior to your taste. The beauty and originality of your car depends now only from the imagination of your owner.

Among the ways to highlight the car from the mass of the same and make it a more spectacular special place occupies the lighting of the machine's interior. Modernization of this kind is ideal for both foreign cars and domestic cars. Which of the backlight is better and how to perform tuning with your own hands?

1 Select backlight for car salon

What is the interior backlight? The devices can be turned on when the door is opened or controlled by a driver using a special console. But the best option is to combine instruments. If you work with the mind, we will get neon lighting of the floor, turning on when opening the door and the diode backlight of the rest of the cabin, running from the switch block.

In the domestic market there are 2 options for upgrading the lighting of the car's interior. The first is the purchase and installation of the LED tape. The main advantage of the diode illumination is the ease of installation with their own hands. In addition, it does not require special fasteners, and for mounting it is enough to glue the ribbon coming in the kit. The standard LED lamp has very small sizes, so that it can be fixed anywhere. It is ideal for illumination of the cigarette lighter and other small parts of the car. Another plus diode tape is excellent impact resistance and tightness. Due to this, its operating time is much longer than other lighting devices. LED tape lights up instantly, which makes it possible to use it to achieve various light effects.

You can also make neon lighting of the cabin. It is characterized by very bright light, which allows you to illuminate a large space. But neon lamps are quite complex in installation and capricious in operation. In addition, neon backlight often blows up with frequent turning on-shutdown and practically does not make the slightest mechanical damage.

2 Installation of neon backlighting in the cabin car

As we mentioned above, it is best to make a combined interior backlight. Next, consider the installation of neon lamps and diode illumination with your own hands.

Start the best installation of neon, which must be located at the bottom of the auto cabin. To work, we will need:

• clamps from Capron;
• a corner of durable aluminum;
• neon lamps;
• set of screws.

Most neon lamps have a cigarette lighter connectors. It is not necessary for us, so it is necessary to cut this part and carefully clean the ends. Next, it will be necessary to sprinkle the corner so that its size coincides with the lamp size, after which it is screwed to the lamp under the mains of the cabin. After that, secure the lamp to the corner using the Kapron Clamps. Thus, the space under the feet of the driver will be highlighted.

The same operation must be done everywhere, wherever you like to illuminate the space of the cabin. One nuance - in the area of \u200b\u200bthe rear seats, the corner must be screwed to the edge to the top so that at least a little to protect the element from damage.

All existing wires must be carefully put under the mats and stretch them to the torpedo near the driver's seat. Connection locations need to be carefully isolate. Next, connect the wires to the door opening sensor and the interior lighting switch. Also, neon lamp wires can be connected to the battery. Before that, you need to remove the wipers, and at the end of work it is possible to place.

One of the wires of the LED backlight should be connected to. This device will notify about the availability of the installed lighting every time you will reflash the engine computer ECU. So neon backlight will remain a whole and does not exceed the chip tuning process.

Now, when you open the door, neon lamp will work. The resulting effect will affect not only you, but also passersby.

3 Mounting LED Ribbons

Mount the diode backlight with your own hands according to the standard scheme. We will need a set of wires, a shrink tube and a LED tape.

Both individual diodes and LED ribbon can be bought in any automata. It is best to purchase the factory model of the tape, since the inefficient option will have to refine.

Start working from the car instrument panel. You need to pull out all the full-time shield lighting devices, then set the diodes on their location. They have the same grounds as regular lamps, so there will be no problems with the installation.

Next, you need to determine the optimal location of the diode backlight. In most cases, it is installed on the entire perimeter of the ceiling parallel to the car body racks. Apply the LED tape in the same way and measure the desired length. The rest can be trimmed. Places for cutting is easy to identify even a newcomer, as they are marked on the tape with special membranes. After cutting, you need to clean the ends and solder parts of the LED tape to each other. At the site of the connection it is necessary to wear sleeve and heat them with an ordinary household hairdryer.

Connect the diode backlight we received as well as neon lamps. Be careful and do not confuse polarity. They are indicated on the ribbons in the slicing places.

As we have convinced, the modernization of the interior of the car does not take away a lot of time and does not require special skills. The only nuance is to be careful and work without a rush.

Each driver who spends a lot of time behind the wheel will not refuse to improve the cabin lighting of his car. However, it is not always time to go for this in the car service. Especially since the beautiful light in the cabin is possible. A high-quality interior backlight will be at all no worse than the service.

LED backlighting car interior

First you need to decide on the backlight site. You do not stand here, aesthetics above all. Select better classic option and highlight the floor under the front seats and under the dashboard.

Also, it is also necessary to determine which light is a monophonic or multi-colored, with the ability to change the color using the control panel. Consider possible options separately.

Option number 1. Multicolor illumination that is fed from the cigarette lighter.

The method of producing electricity from ordinary is the easiest. With this option, it is not necessary to interfere with the electrical chain of your car.

The video shows how the car light illumination looks like:

What will be needed for this type of connection:

• rGB LED ribbon for 4 contacts;
• the controller of such a tape with the control panel, it is using these devices;
• the wire for 4 colors, stranded, about 5 meters long. It is better that the postings in it had the chromaticity of the same as on the controller;
• 4 connector (terminal clamp);
• soldering iron and soldering material, such as solder and rosin;
• silicone transparent sealant.

Before you purchase everything you need for installation, you need to carefully make measurements where the LED tape will be attached, as well as the entire perimeter by which the wires will pass. At first, Merim is the distance under the dashboard, from the side and passenger, where the ribbon will be mounted, then the distance under the front seats. After that, you measure the perimeter, according to which the stranded wire will pass, ranging from the glove box, then through the right passenger seat to the driver's seat and, finally, to the pedals of the car. Leave a little about the reserve.

As a result, 4 segments of the tape and 7 segments of the wire should be obtained. The lighting circuit of the lighting both on the left side and with the right, starting from the glove box, will look like this: tape - wire - connector - wire - connector - wire - tape. Between itself, such a chain is connected by a wire passing between the upper connector. The upper pair of terminal clips is located under the instrument panel, the bottom - under the seats.

The video shows a multi-colored LED interior lighting:

By buying a diode tape, you need to remember that it is possible to cut it into parts only in certain places, strictly along the line coming between metal flat contacts. It should also be remembered that the controller can withstand no more than 12 watts, so it is necessary to pre-calculate the total power of all tape bulbs and, if necessary, reduce its length .

When everything you need purchased:

• cut the tape and the wire to the segments we need;
• cutting the wires from both sides of the plastic by about 1 cm;
• the desired cut is soldered to the tape, each posting to a separate contact;
• then, insulating the place of soldering with silicone glue, so that the wires do not cut off and did not touch.

Ribbon with wires secure on its place with the help of bilateral tape or other material. We start in place under the glove compartment. We skip the wires through the terminal clamp, we attach the controller to it, watches each wire to match the color on the controller. We finish the installation of lighting under the pedals of the machine.

All wires are trying to hide under the trim ,. It remains to connect the controller to the cigarette lighter. Use the usual car charging for a mobile phone. We disassemble it and let the wires along the way, bypassing the voltage stabilizer, it is necessary in order to raise the voltage in charge from 4 to 12 watts. One wire is soldered to the fuse, the other to the leg of the right metal ear bypassing the stabilizer, i.e. to "minus". And stick it to the plug into the controller, and the charger in the cigarette lighter. Learning how to connect the LED, it remains only to master the control panel and enjoy light music.

Using this option of connecting light in the cabin, you need to remember that the backlight will be lit only when the ignition key is turned or when the machine is installed.

Option 2. LED backlight, fed from the battery.

To install, you will need:

• lED tape for 2 contacts;
• the wire consisting of two lives, such as red and black colors, is about 5 meters long;
• soldering iron and material for soldering;
• sealant;
• the toggle switch with the "enabled" and "off" position.

Cut the tape and wires as in the 1st version. Wires solder to the contacts of the tape, each to its pool specified near the contact. We solder the red wire to the positive contact of the tape, and black to the minus contact. Terminal clamps can be used, but you can do without them. How to use them, we already know. It is better to install them, since in the future it will be easier to replace the sections of the sections, and not change the whole tape.

Then the black wire must be reached, stretching it under the rug and the trim. Connect it to the battery. The red wire connect to the bed and further pull it to the plus terminal of the battery and connect it to it. Tumbler placed in a convenient place where it is easy to reach it.
This illumination will work as long as the toggle switch is in the "Included" position.

According to the requirements of traffic rules, any changes in the configuration of the external lighting devices of the car are a direct impairment and entail penalties or administrative sanctions (P 3.1). However, the additional lighting of the cabin with the rules is not directly prohibited, which makes it possible to decorate the car, improve comfort, give the opportunity to consider the map or without tension to read the text in the guidebook. The most popular type of lamps are LED -LAPs, durable and non-discharge battery even with long use. There are several options for mounting backlight in the cabin, which should be considered more.

By default, most passenger cars are halogen lamps of W5W in the ceiling plaffones. To increase the brightness of the glow, LED lamps are usually made. RGB panels appeared on the market, allowing you to change the color of the backlight using the control panel. Installation of such panels is easy - it is necessary to do the following operations:

• remove a transparent cap from the slap;
• remove the stock halogen lamp from the nest;
• insert a special adapter with a plug instead;
• attach the LED panel;
• attach the panel to the bottom of the ceiling with two-way tape;
• close the plander.

Interesting!An option with the RGB panel is convenient because no soldering or other connection is required, all the work is to disassemble and assembling the plafoons themselves. The cost of the kit is small, and the decorative effect is very expressive and varied - some models can create 12 color options and brightness.

Highlighting legs in the car

The illumination of the lower tier of the car interior was first produced only on premium cars. However, quite soon, this option began to be used on simpler models, and some motorists began to set the foot illumination with their own hands. There are special sets that simplify the installation of this type of light design to a minimum. They are a set of 4 lamps and control panel. For nutrition, a plug from the cigarette lighter is used, and the fixation of the elements is performed using pieces of two-way tape. The wires are stacked under the edges of the floor mats so that no one accidentally tear them away. There are less complex kits consisting only of lamps of a simpler design, without a remote. They give a smaller effect, but cost much cheaper. Of the most complex models, you can select kits with the ability to control via a Wi-Fi module.

Read also All about Middle Lights for Gazelle

Contour lighting machine

The contour illumination is one of the most expensive options when buying a new car. Lighting of this type pursues exclusively decorative effect. The appearance of the front panel, dashboard and other elements of the cabin, highlighted along the ribs and plane transitions, is very attractive, it advantageously emphasizes the interior decoration. Luminous lines divide the salon on the zones, separate the dashboard sections, the sheel of the doors, the speed switching unit and other departments.

There are sets that can be installed in the car of any brand. They are produced in the countries of Southeast Asia, so the price of them is available to any car owner. The standard set consists of the following components:

• powerful LED;
• power Driver;
• connecting wires kit;
• lightwater.

The LED is inserted into the end of the fiber, which is stacked in the interface of the dashboard panels or other elements of the cabin cladding. Drivers are powered by overall lights. The installation of a special complexity does not represent. In addition, you can choose the most preferred color of the LEDs, all of them are about 10 options. The cost of the kit depends on the length of the fiber (2-5 m), the presence of a wireless console and other design features. In any case, independent tuning will cost several times cheaper than a regular option that the car is equipped at the factory.

Illuminated instrument panel

The dashboard is equipped with backlight, but for lovers to install additional light elements in the car salon, this is not enough. The owners increase the brightness of the backlight, change the color of each instrument, make the area of \u200b\u200bthe speedometer in the zone of large values \u200b\u200bof red, etc. This issue has a large scope for fantasy, especially since the installation of the lamps is no problem. It is only necessary to purchase a set of 40 multi-colored LED lamps that have the same base, like stock bulbs. From the user you only need to replace the "native" devices to diode lamps, picking up the color for each element to your taste. The procedure is extremely simple and does not require the use of the soldering iron or other tools. It is only necessary to check the performance of the LEDs before installing.

The LED backlight of the car disk is exclusively decorative tuning, which will not bring the car to the owner any use other than aesthetic pleasure from contemplating his car and ride on it. Naturally, the LED backlight, like any other type of car tuning, can be produced in its own garage and not necessarily turn the car into tuning salon, where for such works with you will be taken quite a lot of money.

What highlighting make a car

Let's start with the types of highlighting for a car more than enough. It may be quite simple in the performance of the cabin or feet of the driver and passengers and a more complicated highlighting of the car discs and space under the car. What kind of these types of backlight choose and proceed to its embodiment - the case is exclusively of your taste, because there is no special complexity and a special difference between the installation of the backlight on the door of the car and there are no discs. The main thing is to understand the basic principles and carefully do all the stages of work and then you can get backlighting for the car much cheaper than could do it in the car dealership.

White backlight under the bottom of a white car and a brief instruction on its installation

We will look at the general principles of organizing the backlight for the car and the features of the backlight setting for each element of the car, if there is a need. Otherwise, you can easily use the same techniques and methods that are described below to organize the backlight absolutely any part of the car.


What we need to work:

• LED ribbons themselves
• Wire (four)
• Controller for LED ribbon with remote control
• Silicone glue or silicone gun
• Corrugated thin tube
• Soldering iron, solder, rosin

Read more about materials and tools

LED tapes recently sold more and more. Naturally, the cost of LED tape may have great importance for you, but we strongly recommend that you buy cheap LED ribbons, as they not only often fail and burn out, but do not give the intensity of the glow that is needed for high-quality car backlight . In the event that you still have not decided on the color of the future backlight, we advise you to buy RGB ribbon, which will give you the ability to switch the color of the LED backlight when you want to change the color. It is for this that you will need a controller with a remote control.

There are no special requirements for the wire, as they all perform the same task, and the wire itself will most likely hide either under the upholstery of the cabin, if you make the backlight of the doors or legs, or will be hiding and wasol in the corrugated pipe if you You will make the backlight of the bottom of the car, the number or its disks. In this case, you protect your electronics from water and corrosion on the platform soldering and in those places where the factory braid wires could be spoiled.

In addition, you may need connectors. These may also be the usual "crocodiles" for the test illumination and constant connectors, which are screwed down using a screwdriver and provide reliable contact in the entire system. They are needed not only for convenience when connecting the backlight, but even then, when you need to replace some part of the wiring in case of damage, or part of the LED tape for repair. If you use the connectors, you do not have to fully change the backlight wiring, and you can only replace the damaged section of the chain.

Any work on the improvement of the car should begin with the project. Naturally, at this stage you need to decide on where we will set the backlight and can say exactly how much the wires, LED tape and connectors need to be needed for this. We make an exemplary plan for the location of objects inside your car and celebrate the place where we will conduct wiring. It is simple enough, since most of the wiring can be hidden either under the cabin trim, or to start it under the bottom of the car. However, in this case, it is necessary to purchase and use the corrugated tube to isolate the wire. Let's look at the illumination circuit for the interior of the car and in its example will deal with the process.

Now it is worth viewing your car in those places where you will fix the LED tape itself. The ideal version of the LED backlight is the case when the light source is not visible and only the bright backlight of the car is visible. Moreover, if you set the backlight in a hard-to-reach place, it is less likely that the tape will be damaged while driving or transporting people.
Accurate measurements and cutting LED tape


In the event that you have not yet armed with a tape measure and not measured exactly the length of those objects to which the LED ribbons will be attached, it's time to do it. After that, take in the hands of the ribbon and cut it, but we do it very carefully. The fact is that the LED tape cannot be cut anywhere. For this there are special places located every 3 LEDs. And remember that it is better to make a ribbon slightly shorter than you need, since if the tape is fixed not exactly, but with savings, the intensity of the backlight will be uneven, and this is not worth it.

Soldering and testing

Arming with a soldering iron and solder to the lights of the LED tape ends of a four-core wire. Try to comply with the color of the wires in all places of connection so that you feel easier to navigate when repairing or when errors are detected. We recommend that you insulate the soldering place, check the glow as shown in the figure.
If everything is in order, you can repeat this operation for the remaining segments of the LED tape. Prepare the desired number of connectors in order to connect the resulting LED tapes without any problems at the installation site and also observe the color of the wires.

If you are sure that the segments of the LED tape work as needed and you have not allowed an error anywhere, it's time to take the usual silicone glue or a gun that melts silicone, and pour them platforms. This will not only protect the LED tape from moisture from entering or accidentally closing contacts in spike places, but also help you compact the connection site.
This is quite enough for reliable fixation, so that you can refuse to use the insulating tape.

Glue LED ribbon

Everything is ready to install and connect the backlight in the cabin of your car. To the surface you chose. You can use either several drops of silicone glue, or to attach the tape with the help of plastic screeds - it does not matter. Both options are quite reliable and durable.

If you glue the backlight is not possible, as it often happens when the backlight is installed on the discs, it is worth using a mounted frame from a thin profile on which we will be placed with a tape with plastic screeds, but a little later.

Connect backlight through connectors

With accuracy, observing the color of the wires and connecting the wiring according to our plan, it is worth paying attention to how you will hide the wires. If you have the opportunity to let them under the cabin trim, try to make it as soon as possible so that the wire does not shine. And in the event that you will be wiring under the bottom of the car, first put on the wires insulating corrugated tubes, the ends of which it is necessary to either also pour silicone or wrap the tape. Connectors are best hidden in the same place where the LED tape itself is located, because in this case you will have access at any time.


After all the elements of the backlight of your car will be connected and you hide the wiring, connect the wires according to the controller scheme and you can move to the backlighting organization.

Nutrition for highlighting cars

Putting the backlight in different ways. Someone uses the door panel for this, and in this case the backlight will not only be a decorative element, but also a reminder that the door is not closed, because it will be on the opening of the door. However, this method is not suitable for cases of discs and the bottom of the car, because there the backlight should always burn when we want it.

What kind of powered way to choose

The easiest way to connect the power for the car is the cigarette lighter. It just gives 12 V, so that power is enough for us to connect the entire backlight of our car. To do this, you can only remake the charger for a mobile phone and connect the wires to the chain to the stabilizer that lowers the voltage to 4 V. To do this, it is enough to disassemble the charger for a mobile phone that works from the cigarette lighter and solder one wire to the "land", and the second - Before the stabilizer. This will be enough to ensure the operation of the backlight, and if necessary, the charger is simply pulling out of the cigarette lighter.


However, the most correct option will still connect the power backlight to the battery brace of fuses. In addition, this option will allow you not to disturb the integrity of the factory wiring of the car, which is extremely important.

Check and test

Take into the hands of the remote and turn on the backlight. If you are all done correctly, you can enjoy the ability to change the color modes and even the shades of the glow, and you can even even configure programs for smooth overflows and shifting the color of the glow.

That's what should happen as a result, if you do everything right:

Features of setting backlight on disks and on the bottom of the car

Note that the car backlight is a system that should be constantly connected to a power source, because otherwise it will not work. If you want to make the backlight of the bottom or car disks, the basic principles of work do not change, but an additional stage is added.

If you do the backlight of the disks, the wheel will definitely be removed, and the discs themselves are cleaned from dirt and rust. After that, from an aluminum profile, it will be necessary to collect the design of the desired diameter to place the backlight on it. This design is tightly fixed on the fixed part and connects to the wires with the help of a connector, which in this case will also need to be either isolate or taken into the interior of the car.

Note that the wires and the tape itself should be securely glued or attracted to the design attached to the car disk.
In the case of the illumination of the bottom of the car, everything is somewhat simpler, but it can happen and so that the LED tape will simply have simply. In this case, we can also use a small metal profile that you will not need to fasten to the car body from the inside and glue the LED tape on it. The only difficulty in this process is that the LED ribbon for disks and for the bottom of the car needs to be selected either hermetic, or to seal with silicone or other transparent materials, otherwise, in case of moisture, it simply burns.

Assembly and first departure on a highlighted car.

If you have a backlight of the disks, return the wheels into place and make sure that the wires do not interfere with the rotation of the wheel, and during the rotation the LED tape remains stationary. In case you worked in the cabin and made the backlight of the legs or doors of the car, fuel the wires and put the remote control at a convenient place. Check again if the backlight works and you can prepare for the first leaving to the city.

Before the first trip by car with a new interior illumination, many experienced drivers advise sit in the cabin for a few minutes with the backlit enabled so that your eyes are adapted. The first time the backlight can distract from the control of the car, but over time you will get used, and you will only enjoy bright colors in the cabin or on the disks of your car!