How to make handwriters with your own hands? 3 step-by-step method

the main / Tuning

The use of broad-circular tires put the question "How to make the wheel arches expanders with their own hands" in the category of actual cars and SUVs, where they are installed. This wheel tuning not only changes the exterior of the car. It is usually accompanied by a rather strong pollution of body surfaces, and for cleanliness lovers is a significant minus.

How to make handwriters with their own handsWe will allow us to neutralize such unpleasant moments? You can come to the conceived target in various ways. There are several ways to manufacture and install fenders or wheeled arches in motorists. Consider more.

What does it give?

Well, first, why do you need? What benefits do your car from such a procedure gets? The most important advantage is purely technical. Wheel arches maintain the coating of wings, and doors, from all sorts of mechanical damage to sand and stones emitted from under wide wheels (although here can help).

The following advantages are also important - purity and beauty. Fanders are better protected from dirt, perfectly cleaned, besides - add "pumped" appearance to your favorite.

From foamflast

This procedure can be done yourself, if you are friends with tools and have some technical skill. Fundamentals for fenders can be made from different material. And the feneder itself is usually from fiberglass. A good basis is the expanded polystyrene (in a simple, foam).

Here is a step-by-step instruction of the work of these works.

First, it is necessary to stick to the selected body surfaces of the body of the foam of the desired size (it is better to do Makroflex "Ohm). Pre-surface should be cleaned and expecting at hand;
Then, after the glue dries, the foam is processed by e-mail. Progressive movements are made, rough grinding of parts. A more filigree grinding should be performed using coarse stacker.
Processed foam coating with a layer of a special resin. Let's wait until we dry;
Then the surface is covered with fiber. Make sure that the fiber pieces fit together as a mustache, but neat. It is also important at the right moment to remove air bubbles if they appear in the process of work. We are waiting for, as usual, complete drying;
Then the fiberglass is applied to the layer with a coarse layer. When driving - equal to the surface of the sandpaper. Then use the finish putty.

If it turned out uneven or not as much as you would like, you can repeat the procedure: fiberglass, putty, grinding.

If everything suits, you can proceed to the primer under painting And, in fact, to the painting of self-made details.

Sculptural plasticine

As a basis, you can try to use this beautiful, well-formatted material. The main advantage of such work with it is an opportunity to easily correct the shortcomings in the formed forms of the arches. Below we give step-by-step instructions for these works.

Body working plane Close Scotchpie (better from all kinds - take the greasy);
Plasticine, special, sculpture (sold in stores and in the markets) smear the layer on the wings. Initially rub it into a rapid tape rather thin layer. After - large slices - create a profile volume of parts;
We attach the symmetry of the forms. This is a process that requires a good charming and patience from the motorist, which thus decided to tremble. Nothing if it does not work first time. Excellent material for the basis gives an advantage in correcting errors;
Next - I will apply epoxy and fiberglass. It is necessary to produce in several layers (more than three). We are waiting until it dries;
After drying, we remove the resulting matrices together with sculpture plasticine. And the inner surface of the fender-homemade is cleared of it;
The obtained details are adjusted and fixed on the ground with the help of self-tapping and sealant;
Further, according to plan, finishing work so that everything looks beautiful: putty, grinding, primer, painting.

With the help of mounting foam

As the basis for homemade parts, it is also possible to use an easily accessible and relatively inexpensive foam for installation work. It is only necessary to remember that such a mixture, hidden, increases in volumes. On this occasion, it is necessary to always make some measurement adjustment.

From the universal soldiers sold, the arches from plastic we make shape and fasten them to the wing with self-draws;
The assembly is applied both inside the arches and outside. Expect to complete the hardening of the foam (time is usually indicated on the balloon itself);
When everything comes well, with the help of an ordinary stationery, we give the desired geometry to the fenedoms. Grinding sandpaper;
Reinforce the structure by strength with resin and fiberglass (several layers);
Next, after complete drying, as usual, we produce finishing work.

Now you know how to make the wheel arches expanders with them in several ways. Choose any you most affordable, and you can work.

Editor's Choice