How to open the hood on Ford Focus. How to open the hood by the Ford Focus car? How to open the hood Ford
To the same topic you can attribute several other questions that I ask: "How to open the hood without a key", "Open the Hood Ford Focus 1", "How to Open Hood ford Mondeo."," How to open the hood "and TD on Ford. I'll show you on the example of your focus 2 ...
How to open the hood ff2
Ford Focus 2 hood opens ignition key. There is no cable here, and it's not possible to open it from the salon (at least in this configuration).
To begin with, we will understand how the Castle of the Ford Focus Castle works, in particular - the Castle of the Ford Focus 1 and the Ford Focus Castle 2.
How to open the hood Ford
Castle Hood Ford
As we can see in the photo above, you need to insert the hood ignition key into the lock cell under the Ford branded icon on the radiator grille to rotate up-left. After inserting the key, as indicated on the instructions (in the photo it can be seen), we turn it first counterclockwise (left) to the floor of the turnover, while pulling the hood up, and immediately turn the key to half a turn clockwise (right) - the hood is open.
Castle Hood Ford Focus 1
We look at the photo above. As the radiator grille is far from the hood lock itself, while we are twist the key, we turn this (red arrow) craving, which, in fact, opens the castle. As a rule, the larva of the hood castle breaks. People tend to immediately run with a cry - broke the hood lock, buy the castle of the hood Ford Focus! But, breaking, neither the castle, nor the traction is broken, this thrust (in the photo above) just jumps out of the groove.
But do not worry! The hood can be opened manually by inserting craving into place and tugging this traction from the bottom of the car, prevailing the engine prevailing (see two photos below)
Castle Hood Ford Focus 2
How to open the hood Ford
Or ... Clean the long flat screwdriver through the radiator grille and turn it the same way as the key is done.
How to open the hood Ford focus outside
Replacing the larvae of the hood lock
And the hood is open! As a rule, the locking mustache of the cardanchik's socket, which you see in the photo above are broken or breaking. And the cardanchik already jumps out of his place at every turn of the key and attempt to open the hood. To do this, change the larva of the castle, or insert the cardanchik in place and wrap the tape, and even better - to solder the cardan and the larch.
How to open a hood Ford Focus 2: 8 comments
Is it possible to remove the protection of the crankcase and the bumper from the bottom to get to the castle?
Sure. It is from below, she is removed
the protection is possible and the bumper and the bottom, and on top you need to unscrew because you need to remove the headlights. Nikolai Vasilyevich.
Hello, broke a mustache jack where the cardanchik is inserted - what to do? Thank you.
Hello, are you talking about the larvae or hood castle?
Hello! I have the same trouble, just like that Fugnushka, which you called "traction" I have a slightly different, it is not plastic, but in the form of a cable (rubber on top, in the middle of the iron sting). Somewhere half a year ago, the first case happened to this "opening". Then I found info how to open with a scolder, I put it on top of this cable and put it hard (on a white core), and Comrade at that moment turned the key. Happened! The hood opened, the mechanism collected, everything worked ... until recently. Again the same story, only now the dumping does not help: he has suffered, friends too - everything is not going. I found the topic as a peasant with a split screwdriver, the same white core is delivered and then this turnover serves as a key. Only no one says as before this I took off this cable (traction), which would then go there right in the center.
I pulled this cable on the nerves, he sorted into two halves: the upper rubber part remains from the key side, and from the motor side - iron middle. In short, I do not know what to do next, I would like to try to "please", but I don't know how to remove this cable, can someone tell me?
In the picture, where the inserted screwdriver is shown, a protective plastic grille is clearly visible. This grill can be bare hands and without damage to partially pull out of its fastening grooves, and then, traveled to the reduction of the slot between the case of the machine and this grid, to turn the hand or hand and insert the cardan in the groove. And you can, inserting into one groove, pull out from the larva, scroll into one and the other side, and voila, the hood is unlocked.
Thank you! Today saved the girl - stalled right in front of the big theater.
Look interesting video According to this topic
The content of the article:
How to open a hood Ford Focus. Ford Fokus has a locking hood lock, which is not so easy to open without initial information.
How to open a hood Ford. As we can see in the photo above, you need to insert the hood ignition key into the lock cell under the Ford branded icon on the radiator grille to rotate up-left. Ford Focus. history.
Curious!In all his history, the company's logo varied 8 times, while the name of the Ford never disappeared from the emblem.
The Ford Focus car is equipped with a locking on the castle hood. The opening procedure in some way is original and in the absence of initial information is difficult.
Heat the scum over the flame and try to drown a hot tip in a plastic latch. Or rusted, or just did it fall off, although it can and something else. Home Consultation with the author. Next, you need to perform the following: one of the most common faults of this mechanism on Ford Focus is the situation when the thrust pops out from the groove.
How to open the hood for Ford Focus 2
There is no cable here, and it is not possible to open it from the salon at least in this configuration. After inserting the key, as indicated on the instructions in the photo can be seen, we turn it first counterclockwise to the left to the floor of the turn, while pulling the hood up, and immediately turn the key to half a turn clockwise to the right - the hood is open.
Since the radiator grille is far from the hood lock itself, while we twist the key, we turn this red craving arrow, which, in fact, opens the lock. As a rule, the larva of the hood castle breaks. People tend to immediately run with a cry - broke the hood lock, buy the castle of the hood Ford Focus! But, breaking, neither the castle, nor the traction is broken, this pull in the photo above just jumps out of the groove. As a rule, the locking mustache of the cardanchik's socket, which you see in the photo above are broken or breaking.
And the cardanchik already jumps out of his place at every turn of the key and attempt to open the hood. To do this, change the larva of the castle, or insert the cardanchik in place and wrap the tape, and even better - to solder the cardan and the larch.
Then I found info how to open with a scolder, put it on top of this cable and pressed it hard on a white core, and Comrade at that moment turned the key. The hood opened, the mechanism collected, everything worked ... until recently. Again the same story, only now the dumping does not help: he has suffered, friends too - everything is not going. I found the topic as a peasant with a split screwdriver, the same white core is delivered and then this turnover serves as a key. Only no one says how before this I shot this cable craving, that would then go there right in the center.
I pulled this cable on the nerves, he sorted into two halves: the upper rubber part remains from the key side, and from the motor side - iron middle. As the author came across the kardanchik, who had jumped out of the groove, and to his surprise, he found an even easier way to break the hood without a key. In the picture, where the inserted screwdriver is shown, a protective plastic grille is clearly visible.
This grill can be bare hands and without damage to partially pull out of its fastening grooves, and then, traveled to the reduction of the slot between the case of the machine and this grid, to turn the hand or hand and insert the cardan in the groove. And you can, inserting into one groove, pull out from the larva, scroll into one and the other side, and voila, the hood is unlocked.
Home Consultation with the author. Repair of the castle of the trunk Renault Sandero. How to open a jamble castle. Removal and replacement of spark plugs. Is it possible to remove the protection of the crankcase and the bumper from the bottom to get to the castle? Add Comment Cancel reply. The site works on WordPress.
How to open Ford focus and not getting behind the grille
I drive Focus
Kharkiv region, Energodar
How to open the hood for Ford Focus 2
There is a bla-blah blah about the second generation of focus, and then I will go to the main question: how does the hood offer at Focus 2?!
As you already know, the hood lock from Ford Focus 2 is located under the icon on the grille and open it from the cabin. This is not a normal solution and it sometimes appears. The drift of the hood lock is weak and periodically pops up, so it will not be possible to open the key and will be needed.
What did you think when the hood did not open? The larva broke down? Perhaps, it seems to me that it just flew or jammed the lock bracket.
First look like just to open the hood focus 2
Rotated the key to the floor of the turn left, lifted the cover, and then clockwise right. Just? But you had to notice the absence of a key. Yes, they made it without a key)
How to open the hood if the lock bracket is placed on Ford Focus 2
In order to open the hood without a key, you will need to prepare a special fit or a long flat screwdriver.
We insert it through the grid of the radiator in the groove of attachment of thrust and repeat the usual opening of the lock.
On the video below, it shows how to do it.
If the fastener does not look like this, then a little more hemorrhoids, but everything is very simple.
Turn on louder music. We will be loud and more than once.
Pull the cable as shown in the photo:
Insert a screwdriver and click just above the cable.
It was this place that I was looking for from half an hour.
After clicking on the right place you will hear a click. After clicking, do not remove the screwdriver from this place, as you need to quickly scroll the key first to the left, and then right. I have to emphasize when you find proper position Screwdrivers and the right amount of pressure, the hood suddenly jump out on the left turn of the key, and then it will open on the right, it is important not too redeemed and stopped with a screwdriver. If you do this, then you will lose touch and you will have to start all at first.
How to open the hood for Ford Focus 2
There is a bla-blah blah about the second generation of focus, and then I will go to the main question: how does the hood offer at Focus 2?!
As you already know, the hood lock from Ford Focus 2 is located under the icon on the grille and open it from the cabin. This is not a normal solution and it sometimes appears. The drift of the hood lock is weak and periodically pops up, so it will not be possible to open the key and will be needed.
What did you think when the hood did not open? The larva broke down? Perhaps, it seems to me that it just flew or jammed the lock bracket.
First look like just to open the hood focus 2
Rotated the key to the floor of the turn left, lifted the cover, and then clockwise right. Just? But you had to notice the absence of a key. Yes, they made it without a key)
How to open the hood if the lock bracket is placed on Ford Focus 2
In order to open the hood without a key, you will need to prepare a special fit or a long flat screwdriver.
We insert it through the grid of the radiator in the groove of attachment of thrust and repeat the usual opening of the lock.
On the video below, it shows how to do it.
If the fastener does not look like this, then a little more hemorrhoids, but everything is very simple.
Turn on louder music. We will be loud and more than once.
Pull the cable as shown in the photo:
Insert a screwdriver and click just above the cable.
It was this place that I was looking for from half an hour.
After clicking on the right place you will hear a click. After clicking, do not remove the screwdriver from this place, as you need to quickly scroll the key first to the left, and then right. I have to emphasize when you find the correct position of the screwdriver and the desired amount of pressure, the hood suddenly jump out on the left turn of the key, and then it will open on the right, it is important not too rejected and stopped with a screwdriver. If you do this, then you will lose touch and you will have to start all at first.
Plastic - the enemy of reliability. Perfectly understanding, car manufacturers stubbornly continue to use it in loaded nodes. On Ford Focus of the second generation plastic parts are also found quite often, and in the most unexpected places. For example, the hood lock. The locking mechanism itself is made of metal, but the drive is plastic. How to open the hood for Ford Focus 2 If the castle broke, we will think together.
On the second generation of focus, the drive of the hood latch is not designed as on most cars.
We are accustomed to the fact that the latch of the lock is driven by a cable laid under the hood. It can end the hood opening handle, and the manual mechanism can be duplicated by the terminals of the central lock. On the second focus of the hood lock can be unlocked only from the street and the key - Move the blue oval on the grille, insert the key to the larva of the lock, turn the key to the half-turn counterclockwise, we raise the hood, turn the key to the half-turn clockwise and only after that the hood can be opened.
The Ford Focus Castle Castle Castle Mechanism contains several plastic thrust.
The mechanism, to put it mildly, is not the most perfect, but there is nowhere to go, you have to live with him.
Another feature of the Ford Castle on the focus is the presence of several plastic thrust that do not differ.
According to the reviews of the owners, often the thrust that goes from the larvae to the latch of the castle, it is simply wearing and comes out of the engagement with the groove. As a result, we rotate the key, but nothing happens, the castle is blocked.
Broke the castle, what to do?
There are several options for opening the hood lock if it does not want to open the key. The castle, as a rule, nothing to do with it, because it is metallic and encourages extremely rarely. It's all about plastic traction and plastic elements of the design of the larva. If a broke or worn herself, you can try to install it in place from under the machine.
One of the reasons for the failure of the hood lock is plastic traction.
To do this, remove the engine protection and get access to the lock. At least, you can see what is happening with the mechanism, leaving the flashlight. From the bottom you can and sketch in place and open the hood, and after that it is already diagnosed. The problem is that the thrust is not sold separately, only complete with the lock. But since the castle itself breaks rarely, it is practically no not happening on sale, it is possible to find a lock in parts only on disassembly, and it is worth a new castle assembly at least 3 thousand rubles.
Required instruments for opening the castle.
The second option is more barbaric, but if there is no other way out, and you need to open the hood, we will use it. To open the castle we will need a long (300-400 mm) with a flat slot, flashlight, gas burner (or any other source of fire or high temperature).
Open the hood lock using a long screwdriver.
We do this:
- We light the flashlight towards the lock through the grille, we understand the design and visually find the central plastic heel of the lock, to which the traction should be taken from the larva.
- He warming up the gas burner sting a dyeing and gently insert it between the ribs of the grille.
- We press hot scuffers on the castle plastic heel so as to pay the groove. At the same time, we press the scum as stronger as possible and try to get into the center of the plastic part.
- Hold scrolls in this position for a few seconds when the dumping cools, take it out.
- As soon as the screwdriver cools, again I get sting in a new groove, which we have just paid, and turn the castle as well as the key - counterclock, lift the hood, clockwise, we open the hood completely.
After opening the hood, you can replace the lock or stretch the cable into the car interior.
We opened the hood, now you can either further use the screwdriver instead of the key, or stretch the cable into the salon and open the lock from there in the future. Yet again, there is always the opportunity to buy either a new one, or used lock for focus on disassembly. Successful all work and lubricate the locks often!
Video How to open the hood and change the larva on Ford Focus 2
