Brake fluid Hyundai Solaris: What type and when to change? Replacing the brake fluid Procedure for replacing the brake fluid on Solaris

the main / Repair and care

The brake system on Hyundai Solaris has two contours, they are completely isolated from each other and are divided into parking and working. Such their uses on auto provides increased security of the car. The duty of each driver is charged to monitor their technical condition and spend the liquid on time. How to replace the brake fluid (TZH) on Hyundai Solaris will show in a visual photo of instructions.

When to change the brake fluid Hyundai Solaris

It should be remembered - hydroscopic, which causes an increased absorption of moisture from the air. This becomes the cause of corrosion of the components of the system elements, lowers the boiling point of the TJ and, as a result, the failure of the brakes with heavy loads.

It should also be proceeded to replace the brake fluid if:

changed the color to the darker or noticeable sediment in the tank;
there was a repair of the brake pipeline or a brake cylinder failed;
increase / reduction of pedal stroke, as a result, air appearance in the system.

What and how much mourning brake fluid in solaris

The manufacturer of the car recommends using only certified TJ corresponding to all quality parameters and specifications. For Hyundai Solaris, DOT-3 or DOT-4 FMVSS116 standards is suitable. The original "Brake Fluid" Hyundai / Kia 0110000110 Dot 4 is poured from the factory for filling into the system 0.7-0.8 liters. But if with full pumping and simultaneous replacement in the clutch cylinder, then you just need to take a standard liter bottle.

The level of TZH in the tank must be between the risks of "min" and "max" applied to the sidewall of the tank.

As the car is used, the level will fall. As for the topping of the brake fluid to the level, then there is a couple of nuances. It is forbidden to top up the old TZHSince it is already contaminated by impurities, filled with air, moisture.

The liquid should be addicted to the same brand and the specification, which was filled into the system.

In that case, if the need to attach the EXPLAY, should contact the Hyundai service center for troubleshooting.

Required tools and materials to replace brake fluid on solaris

Tools and consumables required for replacement of the DJ:

new brake fluid;
rag;
key size "on 10";
transparent hose and capacitance.

To quickly and successfully replace the TW and pumping the brakes, it is necessary to attract an assistant, and replacement actions to carry out on the observation pit or the overpass.

The order of replacement of the brake fluid in the system is as follows:

right rear;
left front;
left back;
right fore.

Catalog numbers of consumables for oil replacement:

Original brake fluid Hyundai / Kia 0110000110 Dot 4, "Brake Fluid", 1l bottle, costs 1450 rubles. You can use substitutes from other manufacturers of Fenox SBF4010 "SBRAKE"; Hella-Pagid 8DF355360021 "BRAKE FLUID". The price will be within 200-300 rubles per 1 liter.

Prices are valid for autumn 2017 for Moscow and the region.

We carry out the replacement of the brake fluid on Hyundai Solaris. We unscrew the lid on the brake fluid tank.

Using a screwdriver, remove the mesh from the tank.

Pump the syringe through the spent liquid from the tank.

Install the mesh in place.

Fill a new fresh DJ in the tank to the Max.

We produce a replacement of the TW according to the scheme, starting pumping from the rear right wheel.

We remove the rubber protective case.

Dress up a pumping hose for draining liquid in advance.

Replacing the brake fluid in Solaris - a mandatory procedure, which is performed every 2 years of operation of the vehicle or by reaching 30 thousand mileage kilometers. This recommendation is indicated in the maintenance manual, which is mandatory for users and service centers.

Causes of replacement

The need to replace the brake fluid (TZH) is due to several reasons. If a leakage occurred due to the depressurization of the brake system, then before replenishing the volume to the required level, should accurately determine the cause and eliminate it.

The leakage occurs in most cases due to the destruction of rubber seals of the pistons of brake cylinders or mechanical damage of pipelines.

Technical fluid, filled into the brake system, resistant to low temperatures. It also has a high boiling point that exceeds the 200 C mark. When braking, the node is heated. Because of this, the temperature of the fluid rises, so its quality will deteriorate significantly with time. In addition, technical fluid is very hygroscopic. This is the main reasons why the brake fluid is replaced on Hyundai Solaris and other cars.

With elevated moisture content (more than 2%), the boiling point of the AUT is reduced by 40 s °. This is not critical for the operation of the brake system, but it may cause the process of corrosion process on metal parts in contact with liquid.

To measure the percentage of moisture in the brake fluid at professional maintenance stations, a special device is used - a reflectometer. It indicates exactly when changing the brake fluid. In most cases, in unlicensed car maintenance stations, such a study is not produced. Therefore, the traditional recommendation from specialists - replacement within the prescribed period.

An important question, what brake fluid in Hyundai Solaris? In the brake system of cars that have come down from the conveyor, the technical fluid with the name DOT-4 is poured. It has a Marking Hyundai / Kia 01100-00110 Brake Fluid. This type must be used when tagged or fully replaced.

Procedure for replacement

The process of replacement of the TW is a painstaking procedure that requires compliance with the exact sequence. It can be performed using the compressor. In this case, the forced removal of fluid from the system occurs. This will require an assistant. If it is planned to replace yourself, it is better that the fluid flows free from the system.

From special accessories, a volumetric syringe will be required by no less than 150 ml and transparent hoses with an inner diameter that consistent in the size of the brake fittings. In order to change the brake fluid on Hyundai Solaris, you need to install the car on a flat area and remove the wheels. The order of work is next.

It is important that in the expansion tank there was a constant abnormal volume of the brake fluid DOT-4. Otherwise, the brake system will be delivered. If this happened, a mandatory air removal procedure is required from the system. Due to the air of the brakes can be seized at the very end when the pedal is pressed or disappeared.

Before starting work, you need to know how much brake fluid is needed to replace. Usually 1 liter DOT-4 is enough. If it is planned to replace another brand or on DOT-5.1, then acquire an additional 0.5 liter of fluid, it will be quite enough.

Brake fluid, like other lubricants, requires periodic replacement. This is due to loss of qualities, during operation is lost. So, the process of replacing the brake fluid on Hyundai Solaris is quite simple.

Videos

The video will tell how to quickly and correctly change the brake fluid in the car, and also tells about the nuances and tricks of the process

Replacement process

The brake system on Hyundai Solaris has two contours, they are completely isolated from each other and are divided into parking and working. Such their uses on auto provides increased security of the car. The responsibility of each driver is charged to monitor their technical condition and in time to carry out the regulatory and change the liquid. How to replace the brake fluid (TZH) on Hyundai Solaris will show in a visual photo of instructions.

We carry out the replacement of the brake fluid on Hyundai Solaris. We unscrew the lid on the brake fluid tank.

Tools and consumables required for replacement of the DJ:

new brake fluid;
rag;
key size "on 10";
transparent hose and capacitance.

To quickly and successfully replace the TW and pumping the brakes, it is necessary to attract an assistant, and replacement actions to carry out on the observation pit or the overpass.

So, the change of fluid also provides for pumping the brake system, so we will consider at once two questions in one topic. The sequence of actions aimed at replacing the brake fluid in Hyundai Solaris regardless of the year of release and body model:

For any "fireman", it is recommended to dismantle a minus terminal from the battery.
Using a screwdriver, remove the mesh from the tank.
With the help of pears, we pump out the old liquid from the tank.
Pump the syringe through the spent liquid from the tank.
After that, we pour a new liquid into the tank, and proceed to pumping the brake system.
Install the mesh in place.
Since the contours of the brake system are diagonally, the pumping scheme is as follows: Rear left - front right - rear right - front left.
Fill a new fresh DJ in the tank to the Max.
Now, it is necessary to clean the fitting for pumping the brake system from dirt and other unwanted items. And then, dismantle the rubber protective cap of the fitting.
We produce a replacement of the TW according to the scheme, starting pumping from the rear right wheel.
Take the key to 10 and weaken the tightening of the fitting.
We remove the rubber protective case.
We put on the fitting the tube, and the other end we send to the container where the old brake fluid will flow.
Then remove the hose and wear a protective cap.
Swing the brake pedal 3-4 times with an interval of 1-2 seconds. At the same time, the air can go with the liquid. After pumping, we drag the fitting and then let go. We do so several times until the old liquid comes out from the contour.
Then the assistant presses the pedal 3-4 times the last time until it stops. We take the key to "10", weakening the tightening of the fitting on ½-¾ turnover. It should be waited until the brake fluid is solved into the container. We drain the spent brake fluid together with air bubbles in a pre-prepared bottle. When merging, we pay attention to the color and descend until the net brake fluid goes. Thus, pump all the wheels. Then remove the hose and wear a protective cap. Take the liquid to the MAX mark.
After the work, it is necessary to spin the fitting and put on the rubber protective cap.

Liquid selection

The manufacturer of the car recommends using only certified TJ corresponding to all quality parameters and specifications. For Hyundai Solaris, DOT-3 or DOT-4 FMVSS116 standards is suitable. From the factory, the original "Brake Fluid" Hyundai / Kia 0110000110 Dot 4 is poured to the fill to be needed 0.7-0.8 liters. But if with full pumping and simultaneous replacement in the clutch cylinder, then you just need to take a standard liter bottle.

The level of TZH in the tank must be between the risks of "min" and "max" applied to the sidewall of the tank.

As the car is used, the level will fall. As for the topping of the brake fluid to the level, then there is a couple of nuances. It is forbidden to top up the old TZH, as it is already contaminated with impurities, filled with air, moisture.

Output

Replace the brake fluid in Hyundai Solaris on one side simply, especially those who have already conducted such a process. A newcomer This procedure may seem quite complicated for understanding, and even more so for execution, so in this case it is recommended to contact the car service.

Brake fluid - the required component of absolutely any braking system. Hyundai Solaris is no exception. However, the car owner should understand that it can fully work out all its limit and will have to be changed to a new one. However, not every car enthusiast is ready to give money to the service and seeks to repair everything alone. So, how is the brake fluid replacement?

Required tools

To replace you need:

Syringe or pear to pump brake fluid from the tank;
Rag;
Metal brush;
Pair of liters of water;
A thin hose that will be dressed for draining liquid from fittings;
Capacity, the volume of which is 300-500ml;
Brake fluid about 1 liter;
The key is caped for unscrewing fittings on brake cylinders;
partner who will help.

Hyundai Solaris brake fluid is recommended to change every 2 years or every 45000km run, as it is a hydroscopic and when moisture, the boiling point of the liquid decreases, and with intensive braking, the system mechanisms are very hot, which can cause brake fluid booster and reduce brake efficiency. . Also, the moisture causes corrosion of the internal surfaces of the brake mechanisms, which will further lead to leakage, jam, breakage and replacing these nodes. Replace the brake fluid without problems with your own hands.

We recommend using the Dot 5 brand, as it meets more severe requirements, and the price of it is completely slightly different from Dot 4. The market is pissed by different manufacturers, on what to stop the choice to solve you.

Step-by-step replacement instructions

We visit the viewing pit (if it is missing, you will have to unscrew and shoot each wheel, which will take extra time).
Open the hood and the tank cover.

We take a pear or a big syringe and empty a tank.
Fill fresh liquid in the tank to the mark "Maximum".

Clean the fitting on working cylinders from dirt.

We take a precipitant key and turn into ¼- ½ turnout fitting on the rear right wheel.
We dress on it a hose and omit in the container.
The assistant is sitting in the car and begins to press the brake pedal to repeatedly, while the old tube is on the tube will begin to flow into the container.

Control the process before the fresh brake fluid appearance from the tube.
Spin slightly key fitting.
We ask a partner 2-5 times to press the brake pedal and leave it squeezed.
Reconcile the fitting.
The fluid flows from the tube, and the pedal will fall.
When she stops running under pressure tighten.
We repeat the procedure for pumping 3-5 times.
We remove the hose and wear a protective cap.
We wipe and pour water with water surface.
Take the liquid to the MAX mark.
Replacing the brake fluid on the right rear wheel is completed.
Similarly, change it on the remaining working cylinders by controlling the level in the tank.
We twist the lid and close the hood.
We write the car mileage and the replacement date.
Replacement completed.
Check the brakes on the road. If effectiveness fell - pumping the system again.

This is completed on this. The main thing is to comply with compliance, if more precisely, you need to know which fluid to pour, and monitor so that the restrictive volume is not overcome.

Manufacturers always write in service books on the terms of operation of a particular fluid. TORROSUCHUCH for Solaris can serve only 40 thousand kilometers or, in other words, two from a small year with the average use of the car. Many drivers mistakenly believe that if this substance is in a closed circuit, nothing happens to it. But it is not.

It is worth noting that, in fact, there are hydraulic holes in the expansion tank, through which the liquid, so to speak, is in contact with the outside world. From here and follows one of the most important flaws of such a fluid - it is quite simply absorbing moisture, which is in the air. The longer such contact occurs, the worse the brakesuha works. It is based on this, the manufacturer and calculated the operating framework, it is not advised to leave.

Pack key of a straight line 10mm

The brake fluid is very hygroscopic, absorbs moisture out of air, which, in addition to the emergence of corrosion of the parts of the brake system, reduces the boiling point of the fluid itself, and this may lead to the failure of the brakes with frequent intensive braking. According to the recommendation of the manufacturer's plant, replacing the brake fluid follows after 2 years of operation.

Priority of fluid replacement in brake mechanisms:

Use brake fluids corresponding to the DOT-4 class.

Do not use a merged liquid again: it is dirty, saturated with air and moisture. Always fill in the system only a new liquid of the brand that was filled before.

The brake fluid is hygroscopic (absorbs moisture from the ambient air), so it cannot be stored in an open container.

Protect the environment! Do not drain the brake fluid used into the soil or sewer system.

1. Pump the old brake fluid from the main brake cylinder tank.

2. Follow in a tank clean brake fluid to the lower edge of the bulk neck.

3. Clean the air outlet valves from dirt and remove the protective caps of the brake mechanisms of the front wheels.

For convenience, you can remove the wheel.

4. Clean the air outlet valves from dirt and remove the protective caps of the valves of the operating cylinders of the rear wheels.

Air outlet valves on cars with disk rear brakes are located on the caliper.

5. Put on the hose on the air release valve of the working cylinder of the brake mechanism and immerse the end of the hose into a clean transparent vessel with brake fluid.

6. The assistant must sharply press the brake pedal four to five times (with an interval between pressing 1-2 c), and then hold the pedal pressed.

7. Unscrew the air outlet valve at 1/2-3 / 4. From the hose will begin to flow out the old (dirty) brake fluid.

Brake pedal at this time should go to the stop smoothly. Once the liquid stops flowing, wrap the air outlet valve.

Constantly follow the level of fluid in the tank, not allowing it to reduce it below the MIN tag on the wall of the tank. As the level decreases, tighten the new brake fluid to prevent air from entering the hydraulic engine. Thus, the gradual displacement of the old liquid is new without drying the hydraulic system.

8. Repeat operations 6 and 7 until the fluid is completely replaced (a clean liquid without air bubbles should flow out of the hose).

9. In this way, replace the brake fluid first in the operating cylinder of the right rear wheel, then the left front.

10. Then replace the brake fluid in the second loop (first in the operating cylinder of the left rear wheel brake mechanism, then right front)

11. After replacing the brake fluid, be sure to wear the protective caps on air outlet valves. Damaged caps replace.

12. Check the quality of the work performed: press the brake pedal several times - the pedal stroke and the force on it should be the same with each press. If it is not, go back to the execution of operations 5-10.

13. Follow the brake fluid to the MAX label level on the main brake cylinder tank. Close the tank with a lid.

Photo of tool
Stock Foto Details and consumables

Watch an interesting video on this topic.