How to open the rear seat. When the rear seats are removed

Car seats Not only provide a comfortable ride, but also responsible for the safety of the driver and passengers. When there is a breakdown of the design of the rear seats VAZ 2110 or the need for their cleaning, it is not necessary to spend money on a trip to the car service to remove them. You can do it with your own hands.

When the rear seats are removed

Over the years, all elements of the cabin are wearing the operation of the car. Seats have a tissue upholstery, so periodically need cleaning from dust and dirt.It is best to do it after their dismantling, in this case the cleaning will be really high quality and efficient.

Rear seats can also be required for repair in the following situations:

• after an accident;
• when breakdown the backing mechanism;
• when faulty armrests;
• to pull up the mechanisms of fastening.

Step-by-step dismantling instructions

Before starting work, prepare required tools. To remove the seats, we need:

• flat and cross dusting;
• key on 10;
• pliers;
• remkomplekt (in terms of situation).

It is better to work in gloves to inadvertently do not hurt your hand on sharp metal angles.

Procedure Next:

Video: How to remove the rear seats on the VAZ 2110

Is it possible to remove the backs separately

It is easy to do this, it is also necessary to pull a loop behind the headrest, and then discharge the upholstery and remove the back from the lower mounts. Many motorists complain that the locks are made of low-quality materials, and after several decrees, the latches cease to keep the details normally. Therefore, if there is no extreme necessity, it is recommended to remove the backs along with the bottom pillow. This will increase the lifespan of the seats.

In the model VAZ 2110 fastening the seats are pretty simple. To dismantle these designs requires tools that will have every car enthusiast.

The rear seats on cars VAZ 2110, 2111 and 2112 are slightly different in their construction design, so there will also be different removal procedures. On the this example It will be considered exactly 2110, since at hand I was this car.

So, first of all, you need to remove the bottom of the "sofa". To do this, both with one and on the other hand, it is necessary to remove the special lever to the side and shift the seat.

The end result on the one hand is shown in the photo below:

On the other hand, everything is done similarly, so it makes no sense separately to consider everything.

Regarding the back is also quite simple. First of all, you need to pull the loop up to open the lock:

And at the same time we assign a back forward, as clearly shown below.

And in order to finally remove the back, lifting it up a bit up, thereby removing from the lower loops:

The second half of the back is removed similarly.

Now it remains to remove only the armrest, which is attached separately from the back. To do this, you need to unscrew one by one screw fastening to the brackets from below, both from one and on the other side:

And remove it:

It should not be installed with the installation problems, since everything is performed in the reverse sequence.

Remember MUST! When installed rear backs The seats, watch the loops (for which we pulled at the beginning to unlock) always dropped outside, otherwise it becomes extremely inconvenient to get them to unlock the locks.

If for any reason you need to replace the rear visions on the VAZ 2110, then it is worth saying about the cost of details. The price of the new set of seats is about 5000 rubles - this is a rear row assembly.

Before removing the rear seats on the VAZ-2110, you will need to clarify the details of the work, as there are some nuances, although it is simple.

To start performing work, you will need to weaken the upholstery in the back row.

1. It is attached using the buttons that are located in the trunk.

   Remove the upholstery from the back of the seat.

2. Then you need to take the pillow lock knob and lift the seat.

   Looking down the latch of the back, pulling the loop.

3. Such procedures are to spend on the right and left.

   To remove the back, you need to withdraw the hooks from the body bracket.

4. Then you will need to remove the pillow and take it forward.

   The pillow holds on the clamps, press them and lift the pillow.

5. Half work has already been done.
6. Then removed from the clamps of the head restraints.
7. Next dismantled upholstery.
8. With the hinge, remove the lock lock lock. It is located behind the back of the back.
9. The back is raised, its fasteners from the locks are displayed.
10. It must be done with the left and right side of the back.
11. Then the armrests are shot. To do this, you can use the key to "10".
12. If required, the seat belts are removed. Installation is carried out in reverse sequence.

Removing the back separate

Experts say that the backs can be removed separately, if you pull the lock, which is located behind the seat.

If you press this hook from the trunk, the back should be thrown back.

But there are many complaints about the fact that clamps are made of low-quality material. And therefore can often break. Because to avoid such troubles, then the backrest is recommended only with the pillow. This increases the service life of the chairs.

conclusions

As can be seen, the work can be done quite simple. To do this, you need to know her nuances. Such a procedure may be required at any time, and therefore it is necessary to be ready to eliminate breakdowns yourself.