Original dashboard tuning. Tuning automotive dashboard electronic tuning car dashboard do it yourself

How do you change the design dashboard? Some time, labor, and everything is ready! Consider how such tuning can be done on the example of a car. Hyundai Accent.. Here is a list of what we need to work:

• small pliers;
• sandpaper;
• double sided tape;
• screwdrivers of different sizes;
• photographic paper Lomond Satin, matte, with a density of 280
• scissors.

Stage 1. Disassembly.

We proceed to disassembling the panel. At the top unscrewing two screws. Then disconnect the three connectors and now you can comfortably get at the table and unscrew the devices.

Stage 2. Remove the arrows.

Use for this 2 screwdrivers and a hairdryer.

Watch that tachometers do not suffer.

3 stage. Processing a plastic substrate.

We take sandpaper and sanding the substrate.

4 stage. Intermediate.

As a result of your manipulations on the table there must be the following:

• opaque part of the scale (1);
• old scale (2);
• prints New outside Scale (3);
• substrate scale (4);
• tachometer (5);
• arrow.

5 stage. Prints.

Gently cut out the printout with sharp scissors.

6 stage. Fastening.

Attach the substrate to the scale. Two-sided scotch tape is fed by an opaque part of the scale. If, with temperature amplitudes, the glue does not force the paper, Tol can use it.

Here is an opaque part in the already glued form. For its manufacture, a photographic paper with black fill is used. You can use another opaque and thin material.

7 stage. Collection of design.

We try on the scale using the lumen. The cutters are indicated by numbers 1 and 2. This is a tape, visible through the photo paper. This can be corrected if you make a plastic substrate.

All crepary on regular cogs.

Build panel. The arrow calibration is to car.

8 stage. Calibration.

We warmly warm the machine, in the middle position, fastened the arrow t-ry chilled fluid. We make a rationale - put the tachometer arrow on idling. Most likely, it is not wrong, it can either not move at all or moving jerks. Remove and install it again until it moves as it should! We roll out gasoline and put a "fuel level" arrow in the zero position until the warning lamp lights up.

First, we ride the arrow in the "Polbak" position, after which it starts to move, downstairs or at the top reaching the limiter. Here it must be removed and quickly put in place and secure "on zero". Next, we measure the speed, follow which direction and how much, there will be an error, after which we remove the panel and the device itself. The inner rotating part is that in the rear of the device, we press a screwdriver, and then scroll the arrow.

An important element to which serious functions is entrusted is - it displays some of the characteristics of the car while driving. The driver thanks to her follows the control and measuring devices, looks at the state of light alarm, notifying the normal performance of the majority of most important components and systems. Attractive appearance The cabin can give an additional tuning of the dashboard, which will fit into the overall interior. However, the design should be decorated in such a way that it does not interfere with transportation and corresponding to the minimum requirements passive security. On all factory cars, an ordinary dashboard is always installed, there are several options. modern tuningwhich can be done with your own hands.

Where to start tuning?

In order not to decide to do a car enthusiast, he needs to pre-prepare tools that will be needed during operation:

• hair dryer used in construction;
• ordinary stationery knife or in extreme cases new blade;
• wiring and controls;
• soldering iron.

Most likely, other materials will be needed, which will depend on the preferences of the car owner. It is better to prepare in advance and prepare the tools that will be needed to disassemble the panel, removing the trim and unscrewing the elements in need.

Unscrew the old dashboard

Qualified specialists usually conduct tuning dashboard in a dry ventilated room, it is important that there are no dust in it. Despite such a simple condition, the success of a creative idea depends on it. Dust does not allow exactly sticking the film that changes the color of the backlight of the instruments, and high humidity, in turn, is able to spoil the wiring. To do everything neatly, do not hurry. The trim is best to shoot, this will allow the car to get to the "organs" of the car, following its control and condition. Some motorists change the instrument scale, for this you need to gently remove the arrows as much as possible. An ordinary marker will help in this case, they can mark the point of the arrows connecting. The solder arrows should be removed using a soldering iron, the heated tin will free them from the coil. Performing all the work, you need to be extremely attentive to install the arrows back correctly after improvements. If the connection points are not affixed, you need to calibrate that only employees of the service center will be able to hold.

All sorts of improvements

After full removal and disassembly of the dashboard, you must once again stop and thinking out in detail all operations that are planned. It is necessary to do everything in thought so that the modifications did not affect negatively on the performance of the machine. To date, it is possible to decorate a car by several hundreds of ways, if we talk about the dashboard tuning, then it is worth considering several of the most interesting options.

Complete replacement of the device

Most often, the attractive appearance of the salon car enthusiasts are trying to give a replacement of the scales on the instruments. In this case, the former scale is painted, and a new drawing is applied to its place using a stencil or a specialized film with an existing dial. Production film will help get a better result.

However, the master drivers can independently make a similar film: in the graphics editor, the layout layout is drawn and printed on a special film in the printing house. You can additionally change color gamut Arrows and other elements located on the scale, paint the desired area of \u200b\u200bpaint. An extraordinarily interesting effect of the glow will help create a fluorescent paint, luminous after connecting the LED to the backlight.

Replacing highlighting

The backlight of the dashboard is created by adding LEDs of certain devices. To replace the standard factory backlight on the LED, you should prepare in advance, as this process is quite complex. Remove the old wiring and backlight lamps are not easy, moreover, too many LEDs cannot be installed. It is best to proceed from the calculation of 1-2 LEDs on the device. Such a number will allow to provide a bright backlight, thanks to which, even at dusk, good visibility will be ensured, while it will not act on the eye as an irritating factor.

Sometimes car manufacturers create such devices that are glowing from the inside, and the scale is made absolutely transparent. It is possible to decorate such elements by adding a larger number of LEDs, however, it should be placed so that the direct light comes from them does not interfere with the passengers and the driver, do not blind.

Adjusting the brightness of the backlight

The backlight of the dashboard needs mandatory brightness adjustment. You can adjust it by the device itself, if the light is too bright or, on the contrary, dull, the device will have to re-disassemble and configure. Save time will allow several well-thought-out actions: the backlight can be connected using an alternating record, which edits the intensity of the incident light for several twisted. For accuracy, three times - in the afternoon, in the evening and at night, this will allow you to check for easy access to the appliances.

Complex tuning

Naturally, the comprehensive dashboard tuning will improve its appearance at a time. Updated devices with interesting backlight will provide her new stylish look. If the motorist will decide to improve everything, you will need full set Pre-prepared patterns for scales and LEDs of the same color. If there is no possibility to purchase LEDs of the desired color, ordinary white LEDs should be installed, and required sites Pack the translucent film preferred color. Due to this, the light filter will be created, which will not be worse than light From the LEDs of the desired color.

Conclusion

Complete the process of installing all the removed devices and the full assembly of the panel. It is necessary to do this only after the car owner made sure the correctness of his actions, checked the performance of the system and remained satisfied with the result. You should look at the meals and the fastening status of the trim. The time-consuming process may tire the owner. However, it will be rewarded with a dashboard made by hand. Such a procedure in the service center will cost a large amount, besides, if something is done not as I want, it is unlikely to redo it is hardly possible.

The dashboard is one of the most important components of the car's interior parts, the driver during the movement constantly draws attention to it. The appearance of this part of the internal decoration of the car is always striking. But as it turned out, many motorists do not know the car with their own hands.

By upgrading the design of this part of the cabin, it is important that it is in the end harmoniously combined with a common design and answered all safety requirements.

If you are disgusting your instrument panel and you can no longer look at it, then you will come to the rescue, which you can make your own hands quickly and cheap

Decorative dashboard tuning

This method is to add to the existing external elements Decor. For example, tosing a leather or leather panel, stickers for decorative linings, the use of bright colors for the instrument scale.

To change the appearance and style of the instrument console, you will have to disassemble it.

Devices scale

To replace the instrument scales, you need to measure the old and make the workpiece for a new one. So that everything happens on summitYou can use a special computer program for drawing numbers and divisions. You can play with fonts and experiment with the size, after which it is possible to print and attach to the workpiece, which, in turn, can be made from plastic or self-adhesive film, photographic paper or to an extreme case of color tape.

If you decide the speedometer with your own hands, before installing the new scale, do not forget to remove the shooter and put it back after completion.

Tight salon material

Usually think about a drawing of plastic dashboard, if its coating has lost initial View And obvious defects appeared.

It is possible to perform a qualitatively tightness, only removing the panel. Try not to imagine with dimensions to prevent errors during the cutting. Otherwise, the dermatin will be collected in the folds or stretch.

It is advisable to make the pattern and already cut the material to see how accurate parts are combined into one. When the preparatory procedures are completed, sew all components and fix on the dashboard using thermoclause and self-tapping screws.

Important! , Consider its functional parameters. Not always liked the material looks harmoniously with the salon. He can be glad when sun hits him, allocate unpleasant odors Or, in general, losing the initial species under the influence of high temperature.

Improving console

Under such changes it is understood to improve the functionality of the console. The tuning tuning may be in increasing standard forms and sizes, increasing the brightness by replacing incandescent lamps on the LEDs and installation of additional buttons.

Icons

The replacement of icons can also be part of a general upgrade, but it is necessary to clearly know the panel scheme and represent that as a result you want to get.

To the instrument panel with the replacement of the buttons, you need to remove the shield and remove the factory cartridges and incandescent bulbs. Then decide on the location of the LEDs that will be installed. Try to refer to the choice of shade lED lamps from special attentionSince some at night are tired, and the clarity of the instrument readings can decrease. The shade must be not very bright, but at the same time noticeable.

Glue stickers

Tuning the instrument panel can be done using special stickers. To do this, disassemble the instrument panel and get a substrate with numbers. Do not forget that for each car model, there are options for replacement stickers. Before sticking, try on the native panel, is suitable in size and by location of fasteners, nothing prevents whether to stick it.

When all preparatory actions are completed, degrease the surface and stick a new background for the console.

Full replacement

If all these types of tuning do not taste, you want something more normally, you can replace the dashboard to a new one, the options are a huge amount for each model, but do not forget to be attentive when choosing, since they are all very different and not the fact that Specifically for your car. Now the consoles with a large display are particularly popular, of course, this pleasure is not cheap, but it looks serious.

Of course, we brought in the article only the most instrument panels, with your car you can do anything, for which only enough fantasy.

What you think specifically you will - will be your chicken.

Probably, every motorist, which is the owner of the car of the VAZ family, wants to upgrade its dashboard. On modern foreign cars, the dial of devices from the inside is highlighted, which looks very attractive, as if the numbers shine and the devices itself. But the instrument panels VAZ cars It is highlighted by conventional lamps that emit light on the dial from the arrows from the outside. At the same time, the brightness is low, and the detail of this backlight is little effective. That is why most owners of such cars very often improve the instrument panel using the backlight. In addition, it is quite easy to make it yourself.

To independently make a tuning backlight on VAZ models cars, you do not need to have special skills, but in a specialized company this procedure will cost anything expensive. You can try to make the dashboard backlight from the inside, as on modern cars.

To work, you will need a light-up standard pad for the dashboard. Dashboard S. vehicle It is necessary to remove and disassemble. Do not forget also to dismantle the old lining and arrows of the appliances. So that the backlight light falls from the inside to the lining, the special cuts should be made under the overlay with a heated knife or soldering iron.

Then go directly to the backlight. It will be organized using LED tape. It is necessary to choose a tape that can be easily cut into small parts, three diodes. Regarding the uniformity of the glow, then it is made from the usual foil using the reflector. For the speedometer and the tachometer we take three parts of the tape, and for pointers of the fuel level and the coolant temperature, one by one.

The standard highlighting of the VAZ should be saved, as its task will be the backlight of the arrows on the instrument scale. If you wish, it can also be upgraded if it is possible to glue lED ribbon.. So that the highlighting is not too bright, you can toned it a little. Toning is carried out using a tint film or a black marker. The regular light filter is better left, then the backlight will be soft and uniform with a bluish tint.

Connect all follows to the contacts on the plate lamp plate, pre-determining their polarity. In order to stabilize the current, it is advisable to use the driver to power the LEDs.

Illumination of the instrument panel VAZ 2114

First you need to remove the main lighting lamps together with the cartridges. Next, very carefully remove the arrows, going on with something thin. You can simply turn them around the restrictions and slow down from the axis. At this time, there are a lot of varieties of panels. On one of their part, the arrow drive is attached on the main board, and on the other - on the basis of the plexiglass.

After that, it is necessary to gently remove the insert from the plexiglass. Wear it from the edge and just tear off. The sticky layer should not be contaminated or erased. Insert needs to flip and put on a clean surface. With the help of a blade we erase green spraying, which is noticeable in the area of \u200b\u200bnumbers. Now you can collect plexiglas and insert.

How to change the color of the scale of instruments from the car VAZ

It is necessary to take a piece of plastics and scissors. Cut out the contours in such a way that the plastic will fit into the bulk. Also cut out space for arrows drives. Next, we apply marking for LEDs. For fuel you need three LEDs, for temperature - four. Then set the instrument panel for each scale.

Now, guided by markups, make holes for LEDs and resistance. This can be done by a hot seer or a small drill. The top of the LED should be drowning, as the lens is mounted for the focus of the beam. It is important not to damage the light element itself. LEDs should be soldered in parallel with each other and consistently with resistance.

How to install LEDs instead of incandescent lamps on the car panel VAZ

First, the base of the LEDs must be inserted into the housing and display the connection wires. Next, we make an insert from the plexiglass with the body. Plexiglas should be inserted tightly. From the opposite side, we screw in four screws. Then install the fee. Carefully, the pins of the wires from the arrows should not be brought. Next, we fasten with self-draws or screws. Now we solder to the power supply of any regular lamp power LEDs. We put on the arrows and exhibit them on zero.

How to make the backlight of the arrows of the instruments on the car VAZ

To do this, you will need:

1. Fluorescent marker.
2. Super glue or glue moment.
3. Not power wires.
4. Ultraviolet light bulb.
5. Insert in the instrument panel of the desired model.
6. Soldering iron.

The plastic and the dashboard must be removed, then disassemble it, remove the black plastic and glass, then carefully remove the arrows, then the standard insert. We make holes if there are no them in the new insert. So that the arrows did not stick, it is advisable to make holes a little more than they were in the factory insert. Now you can take out the regular backlight and board with light bulbs.

The neon lamp should be glued on the panel from above, replace the standard backlight and take plastic protection from above. At the top should be attached to the control unit of the neon lamp. Observing polarity, connect the lamp in the place of the standard backlight.

Now mount two lamps on the device. All wires connect and stretch inside partitions. Connect to the point of food and put the lamp. Wires carefully fastened to plastic. Arrows paint the marker several times. Next, we collect and install the instrument panel.

To highlight your car from the gray mass, many car owners make tuning. However, today to produce tuning - this means not only to improve the appearance of the car, but also improve the interior in its salon. One of the options for improving the cabin is the dashboard tuning. You can learn more about this procedure for this procedure, as well as modification options, you can learn from the above material.

[Hide]

Decorative tuning method

If you decide to produce, then you need to ensure the optimal combination of the device with the salon interior. In addition, ultimately the dashboard must in any case answer all the requirements of passive safety.

So, the decorative improvement process itself consists in adding external elements to the existing control panel, for example:

• you can use leatherette for tight material with a panel;
• you can make a procedure for sticker special linings on the scale;
• tuning tuning can also be supposed to provide a brighter device glow.

Consider - to produce tuning yourself, you in any case will have to either partially or completely dismantle the tidy. Next, briefly tell about each of the methods.

Tight tidy

The procedure of PP is relevant in the event that the device has lost its original form, and there are defects on its surface. You can use leathesums, dermatin or other materials as material for the tank. But it must be borne in mind that some materials after a tug can create glare in the sun, as well as highlight nasty smell. Therefore, to the issue of the selection of the material should be approached.

For example, if you decide to use Dermatin to take care, then it should be done on the basis of it, while considering the sizes of PP, as well as its shape. This is done so that the dermatin does not stretch and not going to the fold, so it always needs to dismantle tidy. In this case, you can make more accurate and even seams and joints, and a regular cardboard can be used for cutting. All components of the cutting components are stitched into one unit, while all the seams need to be hidden inside. The material for the plating can be fixed on the glue either the self-tapping screw (author of the video about the drawing - channel Puls Avto).

In order not to spend time and strength on a drawing, you can proceed easier - a special cape on the instrument panel is bought and simply installed on top. Such a pad must be chosen according to the car model.

Color solutions

The tuning of the instrument panel can be convened in the change of color solutions.

The procedure consists of such steps:

1. First of all, you need to remove the sizes with PP.
2. Further, a blank of a new scale is carried out - all the necessary divisions and numbers should be applied to it (there are many options on the network, you can download it ready). Also in stores selling already ready-made decorative dashboards, so if your budget allows you to buy a full-fledged brand device.
3. After that, the template you did or downloaded should be attached to the material that will be used on the new scale. Alternatively, a fine plastic, photo paper, etc. can be used as a material.
4. If you decide to install chrome-plated rings into the dashboard on a tachometer or speedometer or simply put a new scale, then for better fixing the instrument arrows should be removed. Chrome rings can also be bought in the store or internet. Of course, subsequently it will need to be installed in place.

Photo Gallery "Tuning Options"

Installing LEDs

LED panel with their own hands - also quite simple and one of the most common versions of tuning.

Such a procedure is as follows:

1. First, the PP must be dismantled, all regular light bulbs should be removed.
2. Next, it is necessary to determine the place where you mouncent the diode lighting sources - of course, for better visibility, they should be placed around the perimeter.
3. Decide with the color of diodes - it should provide comfortable conditions while driving, while not to interfere with the driver.
4. Further, there are two options - either just replace the bulbs on the diodes, buying the appropriate in the store, so that they come up for regular cartridges, or make the installation of diodes into new places. To do this, you will need to drill holes on the PP, where the lighting source will be installed. Of course, the first option is simpler, there is nothing complicated in its implementation, but we will look at the second method.
5. After the holes are drilled, the lighting sources should be connected to each other with a soldering - you can take a flexible wire for the connection, its thickness should be small.
6. So that you can adjust the lighting brightness, you can add a variable resistor to the circuit. Depending on the model, for this purpose it can be applied in the production of auto a car.
7. If you use white light sources, then in order to provide another shade, you can paint the light bulb with varnish or special paper.
8. Diode elements should be soldered to the power chain, after which it is important to combine them on PP, while it is important to observe polarity.
9. Then diagnoses the performance of the control panel and its further installation on the car (the author of the video is Lesha Master).

Painting tidy

Another option is to paint the instrument panel, or rather, the scales themselves - the tachometer, speedometer, you can also paint the temperature sensors, the volume of fuel, etc. If you set into the shield diode lighting sources, then PP painting (required by luminescent paint) will allow you to give a brighter and modern view device. It is necessary to paint carefully so as not to spray the paint on the shield, otherwise it will be not only the scales, but also traces from the paint, and it will look not aesthetically.