Car backlight LED ribbon. Two ways to independently install LED lighting interior in the car background lighting cabin in the car

According to pDD requirementsAny changes in the configuration of the external lighting devices of the car are a direct impairment and entail penalties or administrative sanctions (P 3.1). However, the additional lighting of the cabin with the rules is not directly prohibited, which makes it possible to decorate the car, improve comfort, give the opportunity to consider the map or without tension to read the text in the guidebook. The most popular type of lamps are LED -LAPs, durable and non-discharge battery even with long use. There are several options for mounting backlight in the cabin, which should be considered more.

Default in the ceiling plates of most passenger cars W5W halogen lamps. To increase the brightness of the glow, LED lamps are usually made. RGB panels appeared on the market, allowing you to change the color of the backlight using the control panel. Installation of such panels is easy - it is necessary to do the following operations:

• remove a transparent cap from the slap;
• remove the stock halogen lamp from the nest;
• insert a special adapter with a plug instead;
• attach the LED panel;
• attach the panel to the bottom of the ceiling with two-way tape;
• close the plander.

Interesting!An option with the RGB panel is convenient because no soldering or other connection is required, all the work is to disassemble and assembling the plafoons themselves. The cost of the kit is small, and the decorative effect is very expressive and varied - some models can create 12 color options and brightness.

Highlighting legs in the car

The illumination of the lower tier of the car interior was first produced only on premium cars. However, quite soon, this option began to be used on simpler models, and some motorists began to set the foot illumination with their own hands. There are special sets that simplify the installation of this type of light design to a minimum. They are a set of 4 lamps and control panel. For nutrition, a plug from the cigarette lighter is used, and the fixation of the elements is performed using pieces of two-way tape. The wires are stacked under the edges of the floor mats so that no one accidentally tear them away. There are less complex kits consisting only of lamps of a simpler design, without a remote. They give a smaller effect, but cost much cheaper. Of the most complex models, you can select kits with the ability to control via a Wi-Fi module.

Read also Middle Lights for Niva Chevrolet: instructions for choosing and replacing

Contour lighting machine

The contour illumination is one of the most expensive options when buying a new car. Lighting of this type pursues exclusively decorative effect. The appearance of the front panel, dashboard and other elements of the cabin, highlighted along the ribs and plane transitions, is very attractive, it advantageously emphasizes the interior decoration. Luminous lines divide the salon on the zones, separate areas dashboard, door trim, speed switching unit and other departments.

There are sets that can be installed in the car of any brand. They are produced in the countries of Southeast Asia, so the price of them is available to any car owner. The standard set consists of the following components:

• powerful LED;
• power Driver;
• connecting wires kit;
• lightwater.

The LED is inserted into the end of the fiber, which is stacked in the interface of the dashboard panels or other elements of the cabin cladding. Drivers are powered by overall lights. The installation of a special complexity does not represent. In addition, you can choose the most preferred color of the LEDs, all of them are about 10 options. The cost of the kit depends on the length of the fiber (2-5 m), the presence of a wireless console and other design features. In any case, independent tuning will cost several times cheaper than a regular option that the car is equipped at the factory.

Illuminated instrument panel

The dashboard is equipped with backlight, but for lovers to install additional light elements in the car salon, this is not enough. The owners increase the brightness of the backlight, change the color of each instrument, make the area of \u200b\u200bthe speedometer in the zone of large values \u200b\u200bof red, etc. This issue has a large scope for fantasy, especially since the installation of the lamps is no problem. It is only necessary to purchase a set of 40 multi-colored LED lamps that have the same base, like stock bulbs. From the user you only need to replace the "native" devices to diode lamps, picking up the color for each element to your taste. The procedure is extremely simple and does not require the use of the soldering iron or other tools. It is only necessary to check the performance of the LEDs before installing.

Make your car individual help different methods. Someone independently pulls the salon, someone seeks to attract attention homemade spoilers. But most often the surrounding impressions of the interior backlight will produce an unforgettable impression.

The lights can burn static or blinking in the tact of playing in the salon music. You can experiment in different ways, the main thing is to apply the necessary durable materials. Then it will not be necessary to redo the diagram or its individual nodes.

When the car's interior lighting is made and mounted, you can select the ways to activate it. As an automatic power on / off, contacts are used from the door opening sensor. You can also use the remote control to include it in necessary driver moment.

Light bands put along the perimeter of the opened door, under the feet of passengers, at the places of standard lighting devices, along the instrument panel, inside the trunk, as well as in the rest of the most likelled salon zones.

Applied materials

The high-quality lighting of the car's salon is distinguished by the competent and relevant use of lighting materials. The most popular sources of light are LED and neon lights. We will analyze the characteristics of both light sources.

LEDs:

• often apply due to their simplicity when installing;
• most of the procurement materials are subject to fixation using the built-in sticky strip;
• each LED takes very little space and can harmoniously fit into the internal zone of standard lighting;
• the mounting tape with LEDs is made of durable material;
• lEDs have a long service life;
• a quick reaction at startup allows you to apply them as light music.

You need to know that before installing the additional backlight of any type, you must disable the battery from the network.

Neon lamps:

• neon lamps have bright unusual light;
• for properly operation service life may be more than LEDs;
• adapted for use in static conditions, without fast on / off cycles;
• sensitive to mechanical impacts;
• mounting takes longer than the LEDs.

Registration of neon backlight

Beautiful illumination in the cabin of the car with your own hands will be using combined elements. For example, the lower part of the interior is made using neon lamps, and the side and upper decorate LEDs. However, no need to abuse such an element of design. It is necessary to arrange everything so that harmony is created.

You need to know that the excess and a large number of motley lights look short.

For the installation of both types of pre-session, we will select materials. You can start from the bottom of the cabin, where they put neon illuminators. For installation you will need:

• set of several neon lamps;
• mounting corner of aluminum;
• plastic clamps;
• self-tapping screws.

In the standard-selling set of neon backlights for the car, the plug is often mounted for connecting the voltage through the cigarette lighter socket. For this operation, it will not be required, so you can pick up a set without it or cut off this plug as unnecessary, and the ends of the wire are cleaned to connect in the scheme.

We measure the length of the aluminum corner for mounting it under the torpedo, we spawn on the desired length and screw in the bottom. Usually mounted first under the glove compartment. On the clamps fix the lamp, directing the future radiation in the desired side. We repeat the operation in the driver's zone and on the rear passenger seats.

Behind the corner must be placed in such a way as to protect the lamp from shocks and random attachments. For this, the corner is fixed with a free edge up.

The ends of the wires are increasing, isolated in places of connection, hide under the upholstery and bring to the torpedo to connect into the circuit. Most simple option It is considered to connect to the door opening sensor or under the overall illumination. It is worthwhile to enter a separate switch for additional lighting.

Dopitive designs from LEDs

Illumination of the cabin using LED begins with the preparation of materials. Most often use two types of RGB or SMD tapes. The second option will be a little more expensive, but it is easier to work with it. Additionally, you can choose single LEDs for the dedicated zones, but more painting car owners are already working with them.

LED counterparts are suitable for replacement of standard lamps with the same constructions of the base. In the other places spends tape. Before installing, you need to extinct the required strip length and cut off the desired piece of tape at fixed points. In the tape, there are usually tight places for breaking the chain. It is for them that needs to be divided. If you cut not according to the specified labels, then there will be no contacts to which the wires are soldered for further wiring.

The ribbon is usually distributed over the torpedo, on the entire perimeter of the roof and descend on the stands of doorways. The fixation is carried out using bilateral tape attached to the LED highway on the reverse side and a closed protective strip. It wept and fix the LED ribbon.

You need to know that when working with LEDs it is necessary to strictly observe the polarity, otherwise they can be spoiled.

To the open ends of the LED ribbon soldering the wires and close the connection with a shrink film. Warming up the soldered closed film place with an industrial or household hair dryer, close from the oxidation of contacts. Next, we output the ends of the wires in the same way as with neon connection.

When using RGB ribbons, you can assemble the circuit with the RGB controller.

Conclusion

Installing a polite illumination in the car does not take much time. If you have all tools and materials, you can spend several hours on the installation. As a result, the car will become more attractive and will receive individual traits.

Among the ways to highlight the car from the mass of the same and make it a more spectacular special place occupies the lighting of the machine's interior. Modernization of this kind is ideal for both foreign cars and for domestic cars. Which of the backlight is better and how to perform tuning with your own hands?

1 Select backlight for car salon

What is the interior backlight? The devices can be turned on when the door is opened or controlled by a driver using a special console. But the best option is to combine instruments. If you work with the mind, we will get neon lighting of the floor, turning on when opening the door and the diode backlight of the rest of the cabin, running from the switch block.

In the domestic market there are 2 options for upgrading the lighting of the car's interior. The first is the purchase and installation of the LED tape. The main advantage of the diode illumination is the ease of installation with their own hands. In addition, it does not require special fasteners, and for mounting it is enough to glue the ribbon coming in the kit. The standard LED lamp has very small sizes, so that it can be fixed anywhere. It is ideal for illumination of the cigarette lighter and other small parts of the car. Another plus diode tape is excellent impact resistance and tightness. Due to this, its operating time is much longer than other lighting devices. LED tape lights up instantly, which makes it possible to use it to achieve various light effects.

You can also make neon lighting of the cabin. It is characterized by very bright light, which allows you to illuminate a large space. But neon lamps are quite complex in installation and capricious in operation. In addition, neon backlight often blows up with frequent turning on-shutdown and practically does not make the slightest mechanical damage.

2 Installation of neon backlighting in the cabin car

As we mentioned above, it is best to make a combined interior backlight. Next, consider the installation of neon lamps and diode illumination with your own hands.

Start the best installation of neon, which must be located at the bottom of the auto cabin. To work, we will need:

• clamps from Capron;
• a corner of durable aluminum;
• neon lamps;
• set of screws.

Most neon lamps have a cigarette lighter connectors. It is not necessary for us, so it is necessary to cut this part and carefully clean the ends. Next, it will be necessary to sprinkle the corner so that its size coincides with the lamp size, after which it is screwed to the lamp under the mains of the cabin. After that, secure the lamp to the corner using the Kapron Clamps. Thus, the space under the feet of the driver will be highlighted.

The same operation must be done everywhere, wherever you like to illuminate the space of the cabin. One nuance - in the area rear seats Corner must be screwed up to the edge to the top to at least protect the element from damage.

All existing wires must be carefully put under the mats and stretch them to the torpedo driver's seat. Connection locations need to be carefully isolate. Next, connect the wires to the door opening sensor and the interior lighting switch. Also, neon lamp wires can be connected to the battery. Before that, you need to remove the wipers, and at the end of work it is possible to place.

One of the wires of the LED backlight should be connected to. This device will notify about the availability of the installed lighting every time you will reflash the engine computer ECU. So neon backlight will remain a whole and does not exceed the chip tuning process.

Now, when you open the door, neon lamp will work. The resulting effect will affect not only you, but also passersby.

3 Mounting LED Ribbons

Mount the diode backlight with your own hands according to the standard scheme. We will need a set of wires, a shrink tube and a LED tape.

Both individual diodes and LED ribbon can be bought in any automata. It is best to purchase the factory model of the tape, since the inefficient option will have to refine.

Start working from the car instrument panel. You need to pull out all the full-time shield lighting devices, then set the diodes on their location. They have the same grounds as regular lamps, so there will be no problems with the installation.

Next, you need to determine the optimal location of the diode backlight. In most cases, it is installed on the entire perimeter of the ceiling parallel to the car body racks. Apply the LED tape in the same way and measure the desired length. The rest can be trimmed. Places for cutting is easy to identify even a newcomer, as they are marked on the tape with special membranes. After cutting, you need to clean the ends and solder parts of the LED tape to each other. At the site of the connection it is necessary to wear sleeve and heat them with an ordinary household hairdryer.

Connect the diode backlight we received as well as neon lamps. Be careful and do not confuse polarity. They are indicated on the ribbons in the slicing places.

As we have convinced, the modernization of the interior of the car does not take away a lot of time and does not require special skills. The only nuance is to be careful and work without a rush.

In almost every car, the manufacturer has provided a backlight that is turned on manually (when turning a special toggle) or automatically (when opening one of the doors). But this is not enough. I want not only to give functionality to the salon, but also to make it brighter and unusual.

So, B. last years The installation of LED backlight in the cabin is becoming increasingly popular. Why not? One side, original tuning Improves interior lighting, and on the other - the car's salon acquires a more solid and interesting view. At the same time, the installation of the LED tape will not cause you any difficulty. How to fulfill this work correctly, we will look at the article.

Mounting backlighting: step by step

The main thing is not to be afraid of such alterations. You yourself make sure there is nothing complicated. Moreover, such tyunig will bring great pleasure, because you transform your favorite car with your own hands. So let's go:

1. Decide on the installation site (this work should be made before buying a tape). Here a lot depends on the design and features of your car. Carefully inspect the boost space, a plot under the glove compartment, an air duct nozzle. You must clearly plan, where a new backlight will be installed and fixed. For example, one of better options Is the ribbon salary directly under the seats. In this case, the space under the legs will be greatly covered.
2. Decide how lighting will be included. Option three - using the button (toggle), when opening one of the doors ( luggage compartment) or when the ignition is turned on. Optimal option - Turning on the LED backlight from the button. In this case, you can use the capabilities of the tape only in the dark, which is allowed to save the resource of LEDs.

1. Decide on the preferred color of the bulbs. Here are already focusing on the color palette of your salon. If the covers are made in blue color, then the LEDs can be bought similar luminescence. After you have decided on all the nuances listed above, you can go further.
2. Buy (prepare) the desired material. Here you will need pliers, an ordinary soldering iron (60-100 W), rosin and tin (it is logical), terminal block (it will be fastened with wires), acute knife, contact groups (will be required to connect a button with wires). In addition, buy a button (you can a regular toggle switch), a degreaser, a small piece of cable (preferably dwelling with black insulation), "moment" adhesive, multimeter (necessarily with the possibility of transversals), indicator, insulating tape, special heat shrink and LED tape.

1. Cut the tape with pieces of the required length. To do this, measure the sections where sticking will be made. Please note that there are special marks in the form of ovals or circles on the LED ribbon. This is done in order to correctly cut and not damage the wholeness of the device.
2. With the help of a soldering iron, tin and rosifers, pay the prepared wires to the contacts of each side of the LED tape. Be sure to check the strength of the contact compound and process it with a tape (better than a heat shrink). Immediately put on the wires on the other hand special terminal blocks (you prudently purchased them in the store). Connects, taking into account colors: black - "minus", red - "plus".
3. Process the degreaser location where the LED tape will be glued. This is very important momentIf, of course, you do not want to flood newly installed legs with legs in a few days. After processing, give the surface of the well-selected place. Similarly, glipe all other pieces of ribbons.

1. Take the wires from one and another tape to the armrest and connect them in parallel with the terminals. Connecting, taking into account colors: Combine red and black wires.
2. Connect the cable wires to the tape contacts connected parallel to the (colors) and pull it under the floor to the installation site of the button. The scheme itself is very simple. Plus from the fuse block goes to the backlight button. Next, the wire goes to LED ribbons (red wires), united in parallel. "Black" wires of LED ribbons Sadim on the housing ("minus").

1. Find a multimeter contacts that will close when the button is pressed. To do this, translate the instrument switch to the call position (diode), click on the button and look for the necessary conclusions. Now sweep the wires to the button. As we said, on the one hand, there must be a "plus" (comes from the terminal block), and on the other hand, the red wire, which came from the LED tapes.
2. Connect the black wire from the LED tapes to "minus", and the red wire from the button to the "plus" pads. Which fuse is to connect to solve yourself (for example, you can sit on the output of the cigarette lighter fuse). To make sure that the exit has the food you need, use the indicator. On the one hand, connect it to the "case", and on the other to the output of the fuse. Now turn on the ignition. If there is food, everything is fine.

Special attention is paid to the connection of the "positive" wire to the output of the fuse. There are two options here: the first - pull the already connected wire, to wind it together with our wire from the button and return to the place, and the second is to bite the already connected wire slightly lower from the clamp and connect to the wire through the terminal.

That's all. Now, when you turn on the ignition and press the button, the bottom of the cabin will be highlighted with bright light. For all the work you will have no more than 1-2 hours.

Output

Do not be afraid to make changes to your car and make tuning with your own hands. Try once and make sure how easy it is interesting. Good luck.

One of the most common types of vehicle modifications is an additional backlight. With it, you can create a unique, fully individual image that will undoubtedly attract the attention of others.

Of course, you can choose a lot of finished options, or resort to help professionals. However, in the presence of certain skills, the independent creation of additional lighting in the car will cost much less, besides, it will allow you to do everything exactly how you want. Therefore, we will talk about creating the backlight in the cabin of the car do it yourself.

Types of backlighting for salon

The backlight in the car's cabin should begin with the choice of lamps. Each of these options have their advantages and disadvantages, but today the LEDs are used more and more. And this is explained by the following advantages:

• Safer in comparison with neon lamps - can not cause fire during damage, stronger, do not contain mercury;
• Less consumption of electricity;
• More convenient to install and further use;
• Light can be sent in the right direction.
• In addition, diode tapes are becoming cheaper every year, which also contributes to their popularization.

Backlight Planning for Auto Salon

Before starting to implement the backlight in the cabin of the machine with your own hands,it should at least approximately estimate the installation scheme of additional lighting. This is one of the main advantages of creating a backlight for the machine with your own hands - the ability to do everything on the basis of individual wishes. Think about where you would like to create additional backlight, as you plan to hold power for it, etc.

Most often, the illumination is placed in the following places:

• Under the glove compartment at the front passenger;
• Near the driver's torpedo;
• In the luggage compartment;
• Near the rear seats of the cabin.

LED backlight can be powered even from the cigarette lighter, and of course you can connect it directly to the battery.

It is important enough to remember that in such things the main thing is to respect certain caution in order not to overdo the intensity of light. Creating a beautiful and "polite" interior illumination with your own hands requires a good feeling of taste and moderation.

In addition, it is necessary to consider ways to switch on the backlight of the car. The following three options are the most popular:

• Inclusion from the button;
• Inclusion when opening doors or trunk;
• Activation of backlight when the ignition is turned on.

What do you need to set the interior backlight with your own hands?

After you have chosen the location of the LED tapes, they chose their color, it is necessary to ensure all tools and materials that will be needed to create a backlight in the car with your own hands, namely:

• Passatia;
• 220V soldering iron;
• Rosin and tin;
• Stationery knife;
• LEDs;
• Glue for fixing the tape;
• Means for degreasing surfaces;
• Indicator;
• Multimeter;
• Cable;
• Switch;
• Screwdriver Set;
• Terminal blocks for fixing wires;
• Tubes, heat shrinking, tape for cable insulation.

Setting the interior backlight with your own hands

To begin with, you need to measure the desired amount of LED tape and cut it on special tags. Next, you need to solder diodes, to the wires of the desired length, the resulting contacts need to be insulated and place the terminals on them. For additional protection of wires, it makes sense to put them in flexible tubes.

The next step in creating a polite interior backlight will be the installation of LED ribbons in the right places. To do this, you first need to degrease the surface to which you will stick the diodes after applying fluid for degreasing you need to wait from three to five minutes. Most LED ribbons have a sticky basis, but it is best to additionally use glue.

During the installation of LED tapes, it is extremely important to ensure that the light will be sent. The lighting should not beat the driver into the eyes, besides, the resulting result will depend on the direction of light. Therefore, before gluing it, it makes sense to experiment with the location of diode tapes.

Wires must be laid under the floor of the car. For standard wiring, you can connect in different places, such a place may be a fuse block. In addition, the dwelling for LEDs can be laid with the help of existing lights, etc. In addition to connecting to a car battery to ensure power, it is necessary to connect the backlight to the "Earth", that is, solder one of the wires to the car body (but only to clean metal without dirt, rust, paints).

In any case, when installing the interior of the car, you must first take into account the features of the internal wiring of your car.