House on wheels from the trailer, the old bus or Gazelle: how to make it yourself? How to make a bus on wheels from the bus

Perhaps there are very few people who would not want to travel and at the same time spend the night at home without using the services of hotels or hotels. Many will say that it is impossible and any trip is accompanied by a hotel room. However, the solution is - an autod or a house on the wheels. You probably saw such mobile structures in foreign films. And it is not strange, because I will say in America, according to the statistics of each 3 inhabitant there is a house on wheels.

Such a house is not only convenient and comfortable, but also significantly saves cashSince the question of searching for housing disappears. On the advantages of the Avtomom can be told for a long time, and there are really many of them. However, one minus is - the car-house on wheels is not from cheap pleasures. But if you have patience and hard work, there is a way out - build a mobile home on wheels with your own hands.

The main need for such a house is traveling, which can be easily sent with family and even small children. Autodom is useful for business trips, you will not have to search for hotels, book rooms, collect luggage and wear it with you.

The main thing is that the driver is experienced, with good driving experience and of course, with a positive attitude towards this type of transport.

House on wheels: What you need for comfort

Although the house will be in the form of mobile housing, but this does not mean that it should not be comfortable and satisfy the minimum needs of the owners.

Lighting at home

To supply light to the mobile home, it will be necessary:

• battery battery type;
• device charger;
• wire system for subsequent electrical wiring;
• panel for controlling electricity supply.

Heating for home

For housing heating, several types of heaters can be used, it may be an autonomous view and gas cylinder. Preferably the use of gas, since in addition to heat, it will provide the possibility of cooking.

If you have chosen heating with gas, then you will have to seek help from a specialist. Of course, to build everything with your own hands from beginning to end commendable, but you should remember the safety of passengers.

Air (ventilation) for home

Very important point is ventilation, especially when using gas. In this case, the holes must be several, and one of them will be as low as possible.

For comfort: water, bathroom, kitchen

No accommodation will be comfortable if it is missing elementary amenities. Well think about exactly where the kitchen will be portable to the size of the "mini" and shower. Also do not forget about tanks with water and pumps for it.

Water that will merge, better send to a large bucket located under the body. To do this, you can use a special hose to be paved in the floor.

Furniture for auto farm

With furniture can occur certain difficulties, because it should be as compact as possible. For such housing, a folding furniture is used, it is fixed on the walls. Purchase such furniture in most cases is possible only to order, which is sufficiently expensive. But if you can make it yourself, it will significantly save funds.

Optional: Doors, windows

As for windows, it is better to do at least 2, so you can save energy and do not include light in the afternoon.

It is necessary to take into account the fact that if the house is constructed from the trailer, the width and height of course should not exceed the dimensions of the car.

Build an autode from Gazelle

If you are the owner of a domestic minibus, which has not liked it for a long time, it can be safely used as the main material for mobile housing. At first, it is necessary to carefully clean it, remove unnecessary seats, the jet is upholstery, get rid of all too much. After clearing, you can proceed to the need for the necessary holes (for windows, ventilation, wires).

The metal part, which is inside, is well covered with a primer mixture to protect against moisture and rust. Next, you can proceed to the flooring of the floor and wall material for thermal insulation. Watch that the material itself is laid smoothly and tight. After you can proceed to finishing the inside of the house plywood you go to another coating.

It is very important to pay attention to the quality of thermal insulation and subsequent coating. All materials must be high quality and respond to all standards. That is how your gazelle and part-time the house on the wheels will last long.

The next important stage will be the conduct of electricity and gas. When these two points are successfully completed, you can start installing tanks with water, bathroom and furniture.

On this, it can be said that the trailer - the house on the wheels is ready. Now you can safely be poisoned on a trip with amenities and comfort.

Build a house on the wheels from the trailer

We will not deny that build an autode from the trailer is not more difficult than from Gazelle. The main difficulty is that walls and ceiling need to be built from scratch, unlike a minibus.

The first step will be the cleaning of the trailer, chassis, paint covering, preventing the appearance of corrosion. After that cover the frame with a dense layer of plywood. Drills holes: frame, timber, plywood and crepim with bolts.

The original design of houses capable of moving was developed at the dawn of the last century. Due to its functionality, the idea of \u200b\u200bequipping housing on wheels has moved to domestic expanses.

Housing device on wheels

If you stick to the installed standards, the mobile home on the wheels should provide the bedrooms of eight people and have a compact kitchen. The remaining benefits of civilization provided for in traditional housing vary depending on the selected model. Most designs include:

• sink and gas stove;
• shelves and lockers;
• oven.

Adherents of comfortable living conditions offer luxury housing models on wheels, equipped:

• grill and microwave;
• bathroom made on the basis of the dry lad;
• washbasin and shower.

With sufficient design area, the tail part is equipped with a separate room with a P-shaped furnishing.

Note! Places for the driver and passenger in the house on the wheels are mobile, it provides an extra area during the parking lot.

The progenitors of non-traditional mobile housing are vans, whose design has been subordinate to the needs of the cattle breeders, the mass production of houses on wheels began since 1938.

Classification of auto houses

Before proceeding with the implementation of the plan to make a house on wheels with your own hands, you should study their gradation and choose the optimal design that happens:

• van;
• trailed;
• houses combined with a driver's cabin.

The duration or frequency of operation also play a role. What is the purpose of becoming a holder of a mobile home:

• the ability to travel without resorting to the services of hotels;
• have an original accommodation for permanent or long-term accommodation.

Prolonged stay in a mobile house determines the need to bother about increased comfortable conditions, which is not required in short travel.

The classification of mobile homes, based on the degree of integration, includes the following categories:

• The A-class value is assigned to fully integrated designs. Appearance such mobile homes resembles a traditional bus, they are characterized high levels Comfort and represent the elite category of housing on wheels. Reasonable attributes of a mobile home belonging to Category A: Big windshield, stationary driver's seat, the presence of retractable partitions, allowing you to competently divide the inner space of the mobile home wheels. Provide autonomous existence allow the generator, gas cylinders and compact containers with a sufficient water reserve.
• Category B has a significantly simplified design. A distinctive feature from the most elementary housing models on wheels is a stationary sleeping place installed in the tail part of the transport. Most often to operate mobile homes of the middle category on the American continent, young couples are resorted.
• C-class represent small-sized houses, providing residential areas of owners during short travels. Often they are construed from SUVs, get a double bed in them by transformation of the driver's and passenger seat.

There are combined houses on wheels, which are difficult to attribute to a certain category, among them:

• Hybrid trailers equipped with exterior tents outside. They allow you to organize short-term rest on removable sites.
• Small-sized trailers of the drop-shaped form provide the possibility of moving a mini home on the wheels by means of a motor transport.
• Trailer whose size is more standard housing on wheels, got the name FIVSVIL trailer. Its transport is carried out by a car with the mandatory presence of a special coupling mechanism.

Re-equipment of the car

Complete task to do homemade house Thorough preparation is preceded on wheels. You will need a large arsenal tools and equipment, the reserves of forces and time.

Important ! Previously studying the legislative framework will avoid unpleasant situations upon completion of construction. Type of transport, housing sizes on wheels must comply with applicable standards.

At the initial stage, the number of tenants is determined for which the mobile construction of the house will be intended. Stripping from this number, transport and interior decoration is selected. You can create a detailed plan on paper. Specialized computer programs will help to simplify the implementation of the project at home on wheels.

Then go directly to the vehicle, most often for mobile housing, the body of a truck is used, it is less common to re-equip the bus. So:

• From the body all foreign objects are removed, dents are rich, the peeling paint is cleaned.
• The design of housing on wheels is impossible to imagine without windows, so at the initial absence of them, the openings for lighting and air ventilation are prepared in the housing.
• If mobile design is planned for long-term housing, do not do without gas valves and ventilation holes.
• The bare parts of metal structures are processed by primer, it will prevent premature corrosion of housing on wheels as a result of aggressive impacts of the surrounding atmosphere.
• Thermal insulation of the house on the wheels is an important point of construction. With this feature, mineral wool, plywood or fenophole will be perfectly cope. In addition to insulation, they will prevent the formation of condensate in mobile housing.

When purchasing metal fasteners, fumble so that they are made of a material similar to the body vehicle. This will create an additional barrier to corrosion processes.

Create a cozy atmosphere in the design of housing on wheels is designed to interior decoration. In addition to moisture-resistant plywood, for these purposes, carpeting is used.

For the side walls of the mobile home, thickened panels are prepared, equipped with straps for fixing furniture. Experts that have experience in equipment design equipment on wheels, are recommended before mounting work with side surfaces to do the ceiling alignment.

After decoration of the walls, they go to the installation in the furniture house.

Having completed the arrangement of housing the place of rest, you can switch to technical equipment Designs at home on wheels. For water supply, you will need to install under the sink of small pumps, supplemented with water cannors. If you wish to equip housing on wheels with high comfort, large containers will be required to take the soul.

Attention ! Water supply at home on wheels is inextricably linked with wastewater, so get comfortable about the presence of an additional reservoir. A traditional garden construction is suitable for the toilet arrangement.

Heat the design of mobile housing and create conditions for cooking will help gas propane. The container with it is fixed at the bottom of the vehicle, there is also equipped with an additional ventilation opening. This will protect the house on wheels from an accident during leakage, since the weight of propane exceeds the weight of the air. The optimal option for the power supply of housing design on wheels is the powerful battery for which the equipped exterior exit during recharging is required.

The process of re-equipment of the trailer

Having decided to become the owner of a mobile home on wheels, you can buy a trailer trailer, which will cost about half a million rubles. Having a desire to travel without overnight stays in the roadside hotels and possessing the skills of assembly work on a tree, it is quite feasible to re-equip an ordinary car trailer, receiving a comfortable house on wheels at the exit. To do this, you will need:

• trailer with a strong chassis;
• wooden lining, rails and bars;
• metal-friendly roof arrangement;
• plywood sheets;
• accessories for finishing;
• tools for woodwork and metal.

Such a trailer on the wheels for housing is not distinguished by a luxurious atmosphere, but a compact bunk bed for night sleep is present. The design is installed in the rear of the house, optimally construct it to the entire width of the trailer, connecting the side walls. This will increase the rigidity of the entire design of housing on wheels. The door is performed from two halves, the window is preferable to make an ercket and a little later.

The whole process of creating a housing trailer includes the following steps:

• The old design is versed for stripping the chassis and coating their anti-corrosion paint. Rama is performed from pine boards, the backups are prepared in the right places.
• For the frame, 2x2 cm rails will be required, additional strengthening of the future house on wheels provide oak rails with a cross section of 3x3 cm fixed on the sides. From above, the frame design is tied with a rake horizontally.
• Installation of the side walls of the future housing on the wheels are made of 6 mm thick classes, for the front and rear walls it is recommended to use a 19 mm thick material.

  Tip! Increase the thermal insulation of mobile housing will allow laying of material with two layers.

• For installation work on equipment in the house on the wheels of the floor, plywood sheets are used.
• Poplar bars are suitable as a roof design for mobile housing. They are fixed with an interval of 30 cm. Then the bars are alternately covered with plywood, waterproofing material and a small cross section.
• The hull of the house on the wheels is equipped with a single window that is located in the back above the bed. Specialists recommend performing the window opening in the form of Erker.
• For convenience and additional light flux, the door of the mobile home is equipped with a compact slad window. The lock is located at the bottom, if desired, the design contains two locks.
• The lower space of the bed of mobile housing is used in two versions: you can equip a retractable table under it or make an extra bed.

We build a cellar with your own hands

If you decide to make a car with your own hands, you will need some basic knowledge, tools, a lot of patience and even more free time. And, of course, a reliable vehicle to create a camper.

This article presents some photos of the house on wheels built by your own hands on the basis car Volkswagen.. Most of the Soviets can also be used during the construction of motorways on the basis of other cars.

Before you start it very important to read the next item!

IMPORTANT! Before the beginning of the creation of a camper with their own hands, it is necessary to legalize the implementation of such a procedure. In this case, you can prevent various difficulties of a legal nature. The rules differ depending on the country, so we cannot publish uniform recommendations on this occasion.

The first steps

Building a house on wheels with their own hands consists of the following steps:

• Outdoor work
• Internal work
• Work on water supply
• Gas and electricity
• Furniture
• Other

If the van is operated only by two people, there will be a lot of space. If you plan to travel 3 or more people, you need to consider the number of places. Remember that places should be equipped with appropriate safety belts.

How many places to sleep do you need? One option is to arrange a bunk bed for children. If you have a reserve of place under the roof, you can make a "drop-down" bed.

At this stage, you must have a clear plan for further action. Of course, you can improvise, but much easier to have a thoughtful plan on paper.

Outdoor work

The first thing to be done in the preparation of the basic vehicle is a thorough cleaning of the inner part of the car.

At this stage, it is also necessary to consider the form of the body as a whole. It is time to deal with body damage, rust. Local or full painting Auto.

As a rule, vans have no windows, so you can think about their installation. They are needed to provide the influx of fresh air and entering sunlight inside the autodoma. The windows are of different shapes and sizes, the choice depends on your preferences and body features.

During the construction of the house on wheels, there will have several holes in the car body. We are talking about holes for ventilation, gas output (in case of leakage), exhaust gases Heaters, filling gorlovin for water, etc. Some of them can be made later, but it is much easier to solve the issue now, if you know exactly where they will.

Do not forget to apply primer in all places where naked metal appears to prevent corrosion.

Build your own autod right!

Internal work

Most likely, the wagon will be partition behind the front seats. Some partitions are attached to screws, others weld to the body. Solve the problem will help "Bulgarian".

Remember the need to use protective products. Sparks can leave unpleasant stains on the glasses, from which it is impossible to get rid of.

Begins the most interesting. The insulating layer is very important because it will protect your camper from external noise and temperature. There are many materials that can be used. The choice depends only on you.

In this case, was used material Armaflex. It should be cut into pieces and glue. The main point is the protection against moisture. If the insulating material does not protect the moisture from entering, it is not worth using it.

It is necessary to prepare insulating material, lightweight and moisture-proof, as well as a soft and flexible carpet.

For side covers, a thicker phaneer should be used, as Furniture will be installed on them.

Use glue or sealant with a large temperature range for the insulation and carpet coating on the side walls. Because the van will be exposed to both the minus temperature and the hot summer sun. Also will affect the work of heating. In the case of the use of poor-quality glue, it is necessary to redo it again after a while.

Where to begin? Start sowing an autode, ranging from the roof and ending with the floor. First, mount the insulation and facing layers on the ceiling, then go to the side panels.

Use wooden planks on the floor to equip sufficient space for isolation. Reiki are attached to the floor with the help of the appropriate sealant. Then the layer of insulation is stacked, after which it should be covered with plywood. Plywood is fastened with sealant or screws.

Remember the water supply, as well as the need for laying electrical cables and gas tubes. Wires and hoses can be paved through isolation or under plywood lids, if you already know where all the devices will be installed.

Work on water supply

The house on the wheels should have the supply of cold running water. For this, two canisters with water are installed under the sink. Submersible pump Provides water supply to the crane.

If you need warm water, extra sink or shower, the system will be more complex. You can install large water tanks in another place, for example, under the van. Support hoses to combine the entire system.

When you make an autode yourself, only fantasy limits you.

Do not forget about wastewater. You can set the appropriate tank under the car or pave the hose through the floor to merge water into the portable tank or the usual bucket.

Remember that the water used will terribly smell like in the summer and freezes in winter. Therefore, it is necessary to get rid of it as soon as possible, so the bucket can become an ideal solution.

What about the toilet? You can set one of the comfortable portable toilets.

Gas and electricity

IMPORTANT! Gas supply hoses and electrical wiring must be installed only by qualified specialists! In case of incorrect installation, they may be of serious danger. Make an autode on your own, but do not expose other people at risk.

Propane In Cepers can be used for cooking, heating, as well as refrigerator connections. You can do without it, using electric stove and refrigerator, as well as a stand-alone Webasto heater.

The gas cylinder must be stored in a separate location with holes at the bottom. Why is the hole be undeporting? Because propane is heavier than air, so it will always go down.

You can even make a valve to connect the gas stove outside the car to cook food outside the van in the future.

Again, build a camper right for your own security!

Electricity Need to launch all devices designed for 12V. The system consists of a battery, charger / converter, control panel and a plurality of wires.

Do not forget about the external connector, for charging the autodoma battery from the usual power grid (110V or 220V). You can also use it at home, charging acb during winter storage.

In order to determine which battery capacity you need, easy calculations will have to perform. Let's say you will use the following:

• Halogen lamps: 2 × 20W 2 hours a day \u003d 80 WT⋅ch
• Refrigerator: 45W 12 hours a day \u003d 540 VT⋅

The total power consumption is 620 VT). Now divide the 620 VT⋅ch by 12V and you will receive 52Ah. This is your daily power consumption. As a rule, the battery per 100Ah is enough for about two days of autonomous work.

Calculate, taking into account energy consumers you use. This will help you get the average power digits of electricity consumption.

Gas and electricity are very important issues that need to be considered during the construction of a camper. If you plan to send an auto toward travel away from civilization, autonomy should be maximum. Do not hurry, we carefully think over and calculate.

Furniture

In this question, nothing limits you. You can boldly realize your dreams. Make and install furniture in different ways.

Sometimes quite suitable furniture occurs on various disassembly, we advise you to search. Non-good offers sometimes appear on the Internet auctions, and the furniture is sometimes sold at quite an affordable price.

You can also design everything from scratch. Some firms sell ready-to-install parts, veneer coating. You will only have to apply lacquer (if necessary) and install furniture. You can also contact a professional who will help you in this matter.

Make a person's personnel - not too complicated task for an experienced master. But the dates of such construction can be strongly delayed due to the continuous improvement of the design. In order not to get into such a situation, you should think in advance the interior, refusing obviously unnecessary elements. This is especially important when equipped small carsFor example, when creating a house on wheels from gazelles with your own hands.

The mobile home has indisputable advantages - comfort, comfort and mobility. Moscow is a noisy city, from which you want to sometimes leave. The owners of trailers do not have to look for a place for overnight stay, and travels become very economical. If you used to use this original housing, it was not possible to get an opportunity, you should first get acquainted with their classification.

Types of auto houses and their classification

Choosing the type of future mobile housing, one can be guided by its division by:

• kind - there are trailed, van or combined with a car at the wheels;
• class - distinguish three classes of autodomas comfort;
• trailer type - exist trailers trailers, hybrid and fifth-wheel trailers.

If everything is clear with the trailed view of the mobile house, then the difference between the van and combined auto-bodies is not immediately visible. In the first version, the residential premises is located in the car van and separated from the driver's seat.

Such an option is suitable when traveling together, when no one remains in the "house" at the time of relocation. Thanks to this design, it is possible to enter more functional furniture using a deaf front wall.

Converted from Gazelles or minibuses of the Avtomom is just combined.

Comfort class can be called conditional. So, to homes on the wheels of class A "include spacious trailers made on the chassis big trucks. Outwardly, they resemble a bus, may have folding structures, and inside the functionality they do not differ from a small apartment.

It should be borne in mind that the driver should have the right category "C" to manage this transport.

The spaces in it are much smaller, but still traveling in them convenient. What is important - it is possible to manage such a car with the rights of category B if the weight of the car or the total weight of the car with the trailer does not exceed 3.5 tons.

The class "C" indicates the most simple autoomom. It may be a small trailer or converted to a minibus. There is no separate sleeping place here - its function is performed by folding sofas or chairs. But equipping such a mini camper with a trunk-tent, folding canopy and a set of furniture for camping, you can get a comfortable stay with a minimum cost.

Similar trailers designers are also called hybrid to distinguish them from simple trailers. Separately, it is necessary to note the FIVSVIL trailers, the form of which is designed for use in conjunction with pickups. Due to this, it is possible to reduce the length of the entire caravan, because part of the trailer hangs over the body of the car.

Errors in the construction of houses on wheels do it yourself

Prices for mobile homes are noticeably "biting". Not surprisingly, the desire of the mace of the heads of families to save the budget and do it all. It is important to be wise and learn from other errors:

• it is not necessary to do all of the girlfriend - the house will have to live at least a week and you want to stay with comfort;





• it will require serious refinement of the body, the heating systems, wiring - without the skills of the car mechanic, do not do;



• if the shower and the toilet still managed to enter, do not forget about the tank for a drain - pour out dirty water on asphalt or the lawn is extremely unethical;
• it is better not to forget to make a connector for connecting 220V on camping parking, well, and the converter for 12V from the car battery.

Production of trailer with its own forces

If the difficulties are not frightened, and the desire to action is not strangular, you can try your strength in the construction of the house. And to redo the gazelle or build from zero trailer trailer - the choice is strictly individual!

House on wheels from Gazelle do it yourself

You will need a Bulgarian, a welding machine, a hand saw on a tree and a lot of patience. Phased the modernization of the car looks like this:

1. The seats from the cabin are taken, the old sheathing is removed. All metal parts are processed by a special solution that prevents the appearance of rust. Walls and ceiling are insulated with foam polyethylene, plywood sheets are laid on the floor. The entire wiring passes under the sheaving of the floor and walls, it should be thought out in advance.



2. Right in the bodies are welded frame for furniture. If you set a smooth car, you can not use a pipe as a level, overlooking the ends into the bottom edge of the window openings. After a draft welding, the frame is removed and everything is welded, it is cleaned and reappeared inside.



3. Window openings are punishable by carpet. Ceiling panels are also installed. After the interior is completed, it is possible to mount the racks under the mezzanine and mount furniture frames.



4. For the front seats, you can make a swivel mechanism. To do this, you will need anterior hub, for example, from VAZ and part of the rotary rack. The scheme is quite simple.





5. The final stage is to install furniture on the frame, the connection of the lighting, the installation of the pump for the kitchen service, the trimming of the antlesole and minor improvements in the interior. For cooking, you can put a small gas stove per single burner.



6. Instead of welding the furniture frame, you can use ready-made headsets, reinforcing them from the inside with corners and additional screws. Bold the kitchen is also needed to everything - the floor, sofa, wall. This is done to protect the furniture from the breaking during the movement along the bumpy roads.

We should not forget that such a remission of the car requires registration in REO. To do this, you need to write a statement and get a resolution from the Tehotel of the State Training of the FAI and the Protocol of an authorized organization.

Stylish plywood trailer

If there is a carbon car, sin does not take advantage of the situation and do not make a pretty trailer "drop" for overnight stays outside the city. For this:

1. Side walls of the future van are cut and attached to the base. All holes under the doors and windows, as well as to relieve the frame, should be cut in advance, so it's better to think about the drawing.



2. Shelves are collected from the furniture shield and are installed on the base. The same shelves will perform the functions of the front and rear walls of the van.



3. On the shape of the van above the shelves on both sides, a plywood sheet bent, the power frame of the bar is fixed above. One side is made lifting, opening access to the kitchen.





4. The top hatch and the roof window is cut. The entire frame is insulating, the wiring is stacked.



5. On top everything is stuck with veneer sheets. When door and window openings are cut, you can proceed to the outer painting and varnishing.





6. Installed doors, top hatch and supply and exhaust ventilation. After fixing all the accessories, overall lights and wings for the wheels, you can safely go on the journey!

And the video shows the detailed assembly of the autooma with the installation of solar panels:

A car on the wheels, and even equipped with your own hands, is the dream of many lovers of auto travel and outdoor activities in nature. It provides its owner an amazing freedom when traveling, freeing from the need to search and book a hotel, acquire tickets, pack the suitcases, etc. In addition, its own car can easily travel even a large family, including pets - for this it is necessary to use appropriate furniture , as a rule, transforming.

When for the first time appeared on the road an auto trailer on wheels to answer rather difficult. The first such experience was implemented by Jennings in the 38th year of the last century, although homemade samples of highways appeared much earlier. All autoomom on wheels can be equipped with almost all the necessary attributes of the usual and comfortable life - Bathroom, shower, gas stove, full-fledged sleeping placethat are present even in the smallest auto-volumes that budget Gazelle is often taken as the basis of which in Russia.

Depending on what kind of motor belongs to the wheel on wheels, it can be:

• trailed;
• van;
• combined.

A fairly common practice is currently the personnel re-equipment of suitable transport, the same domestic gazelle, in comfortable auto-volume for travel. But before making an autode on wheels with their own hands, it is necessary to determine the main goal of re-equipment - long or short-term accommodation in the auto house, as well as pick up or make appropriate furniture.

Classes of houses on wheels

According to the generally accepted classification, all autooms on wheels are divided into three main classes:

Attention! Any autod class "A", made on the basis of a bus or truck, according to the transport classification requires the rights of the category "C" by the driver.

Speaking about the classification of the "Wheel House", the following concepts should be highlighted:

Tent trailer

The homemade autode on wheels does not necessarily have to be expensive and complex in the manufacture, especially if it is used relatively rarely and for a small number of people. Some types of highways do not even require the installation of furniture, and are used as a bed. In order to independently make an autode trailer, you will need to make certain efforts and a sufficient amount of time.

The main "power" element of such a car - frame, can be purchased at a finished form, or to assemble it yourself, for which the skill and certain technical knowledge will be required. With independent manufacture, special attention should be paid to the anti-corrosion processing of all steel elements of the future autodoma.

The frame, mounted on the chassis prepared for the autodoma, can be both steel and wooden. The focus on its creation should be given to the quality of the compounds of parts, since when such a trailer-autodoma is moved, the entire design will be subjected to serious dynamic and vibration loads. Inside such an autodoma, you can position a sufficiently convenient bed, and at the time of stops on vacation, the construction of the autoomom is unfolded, and the tent is quickly installed on top. Such an autode on the wheels, the photos of which is presented below, is optimal for short trips and easy-to-go outdoors.

Another option of such a trailer can be viewed on the video:

How to make an autode on wheels do it yourself

In order to make an autode on wheels with their own hands, you can use any minibus, freight car or even a bus. In order to create it, you will need to make a lot of effort, time, and be prepared for quite serious material investments, which subsequently pay upon comfort when traveling in its own auto farm.

The process of turning the standard Gazelles in an autode on wheels will necessarily be accompanied by a number of works that are mandatory:

In the case when the trailer house on wheels is created with the goal of long journeys, it is advisable to provide for a good audio video system and satellite TV. If financial capabilities allow, it will be good option Installing solar panels that will extend the operation of the generator.

Attention! In most cases, the re-equipment of the vehicle in the trailer Avtodom requires to pre-bind all the "alterations" to avoid legal problems in the future.

Internal work

Many lovers travel comfortably interested in the question - how much is authod on wheels in Russia, but learning the cost ready option Prefer to engage in the creation of the autodoma with their own hands. And this is not deprived of meaning, because to make a car on wheels from Gazelle with their own hands by any person, ready to attach a certain amount of effort and spend its time.

The first thing that will be needed to be made inside the cabin of the future autodoma on wheels is to dismantle the partition located for passenger seats. If it is attached by bolts, there will be no problems if the welded connection is used, the Bulgarian will be required. After dismantling, you should completely free the interior from the interior decoration. In parallel, it is worth checking the metal parts for the presence of corrosion foci. Take measures to eliminate them to disassemble ready car It will be much more difficult.

Before proceeding with the insulation and interior of the autodoma, it is necessary to thoroughly consider the water and power supply system, Since all pipes and electrical cables are better hidden under the trim - it will avoid their accidental damage. After that, an autode on wheels on the basis of Gazelle requires serious insulation. In addition to special materials with vibration insulating characteristics, basalt mineral wool or extruded polystyrene foam can be used for auto far.

An important moment in the autodoma finish on wheels inside and outside is the protective processing of the material used. So, additional metal elements outside the autodoma must have high-quality anticorrosion processing. The elements of the internal object are performed, as a rule, from wood. To process them, it is recommended to use a special flame-protected impregnation, which will prevent the spread of the flame, will not allow the fungus to form, to get rid of which it can be simply impossible.

Certain ideas for creating your own project can be "borrow" from manufacturers of such houses, looking at the following video:

Gas and electric equipment

Any car on wheels - Mercedes or Gazelle requires a special relationship in terms of electricity supply. It is not necessary to naively believe that, without having an appropriate formation, you can qualitatively perform electrical wiring and install the appropriate equipment in the autode. The same applies to gas equipment.

For example, few people know that for a gas cylinder in any auto house, it is necessary to "highlight" a separate closed zone, at the bottom of which the holes communicate with the outer atmosphere should be present. This is allowed to allow propane, which is heavier than air, when leakage from the balloon "leave" an autode on wheels, and not cause poisoning or fire in the cabin.

An important point For autodoma is the correct calculation of the battery power. To ensure maximum autonomy, you should summarize the daily power consumption of all devices present in the autodomome. The resulting value in watts will be required to divide by 12 (V), resulting in a value in amps-hours (AH) - it is precisely it is indicated on the battery and allows you to judge its power. So, When energy consumption in an auto-volume 50-60 AH / day, optimally acquire a battery in 120-150 AH. Such a car machine on wheels will be able to function offline two days. It is advisable to provide an external socket to recharging the autodoma battery in the parking lots.

Furniture

Despite the fact that it will not be a problem in the purchase of finished furniture for autoomom, according to reviews, it is not able to satisfy all the requests of the car owners, especially creating an authome on wheels on their own drawings. therefore optimal option It becomes either its independent production, or an individual order on furniture production.

In most cases, an independent manufacture of furniture is more optimal. Since for a small car, for example, on the basis of standard Gazelle or UAZ, furniture will not need much, and it is not different, and it is not different, at this stage of work you can save. For a proper level of comfort in the auto house, as a rule, the following furniture structures are manufactured:

• dining table, to save space in a small auto house, it is better to use a foldable option;
• kitchen table with washing and working surface;
• open shelves or boxes located under the Ceiling of Avtomoma;
• in the presence of a toilet in the autodomy on the wheels, it will be necessary to make a partition with a door.

When a KAMAZ or bus is taken as a base for auto-volume, the number of furniture listed above increases. Made by an autode on wheels with their own hands, to facilitate the task of determining the type and number of furniture, you can use special computer programs, or draw a detailed plan for the future planning of the Avtomom on paper, where it is clear not only the type of furniture, but also its location.

How can the most expensive house on wheels can be done in the photo - perfectly visible how exquisite and comfortable can be interior decoration.

Construction house on wheels do it yourself, it is worth paying attention to the quality of materials. So for furniture It is advisable to use moisture-resistant materials resistant to household chemicalsBecause cleaning in any type of autoomom - from the bus, trailer or gazelles, often often.