How to change the fuel filter on Chery Tiggo. How to change the fuel filter on Chery Tiggo change the fuel filter on Cherie Tigo

In accordance with the recommendations of the manufacturer fuel filter Replace after 2 years of operation or 20 thousand km of mileage. However, taking into account the experience of the operation of cars in russian conditions We recommend replacing it every 15 thousand km of mileage. Rods when moving a car with a high probability indicate a clogging of the filter.

The fuel filter is located near the front right part of the fuel tank and is fixed on the base of the body, so it is more convenient to work on the car installed on the lift or observation ditch.
1. Reduce the pressure in the fuel supply system (see).

2. Squeeze the locks and disconnect the tip of the discharge fuel line from the filter.

3. Similarly, disconnect the tip of the supply fuel line on the other side of the filter.

4. Disconnect the wire shoe from the fuel filter.

5. Press the spring fastener spring ...

6 .... And remove the fuel filter.

7. Install the new fuel filter in the reverse order, so that the arrow on the cylindrical part of the filter housing coincides with the direction of the fuel flow.
The tips of the fuel hoses connect to the filter by the movement along the fittings before snapping the clamps.
A warning.
After installing the fuel filter, you must check the fuel filter connections with fuel lines using the gasoline leakage. If necessary, repeat the operation of connecting fuel lines to their reliable fixation. If the leaks from the compounds are not eliminated, replace the sealing rubber rings of the tips of the fuel lines or fuels assembly.

On the cotor Chery. Kimo (Chery Kimo) The manufacturer recommends changing the fuel filter every 20,000 km of run or after 2 years of operation. But, given the quality of our gasoline, the Council change fuel filter every 10,000 km run (at one time C) will not be erroneous. Since the contaminated fuel filter will not bring anything good to the car. Some problems are the loss of engine power, an increase in fuel consumption, heavy engine launch ... And at the same time the cost of the filter itself is not large, the process of its replacement is not complicated (everything can be done independently). Does it make sense to save and pull the filter replacement time? I think no. But, you decide. You can disagree with me, say that ten thousand is not serious. Why so early? I will not persecute. But, exceed the recommended twenty thousand, I would definitely advise you.

Spare parts. Catalogue number Fuel filter car Chery Kimo. (Chery Kimo) - B14-1117110.

Tool. First of all, we think about the place of work. As to replace the fuel filter on Cherie Kimo You will need an observation pit, an overpack or a lift. From the ground to replace the filter will not work. After reading the article to the end, you will understand why it will not work. Further, a few words about the instrument that will be needed to perform the task. And so, to quickly and successfully replace the gasoline (fuel) filter, you will need: gasoline collection capacity, short cross screwdriver (flexible screwdriver, too, option), simple or sliding passage. Also, I advise you to purchase or make the Passatii itself to compress the fixtors of the fuel tubes (an example of homemade passas in photo 1). In theory, these clamps can be squeezed with fingers and pull the tube from the filter. But, in practice, these clamps often have resistance. Therefore, the presence of two mechanical / metal "fingers" - welcome.

The procedure for replacing the fuel (gasoline) filter by car Chery Kimo (Cheri Kimo):
We begin to work on replacing the fuel filter from the pressure discharge in the fuel supply system. We drive cars to the observation pit, the wasting engine. In the fuse box located in motor compartment Near the battery, we find the fuel pump relay (photo 2). Pull out it and run the engine. After a few seconds, the engine will stall. And this is good, since the pressure in the system will be reset that when working with fuel tubes, it will avoid the gasoline soul.

Next, you should find the filter itself. Thus, answer the question - " Where is the fuel filter on Chery Kimo? "By car Chery Kimo, he is located near the gas tank, with right sideAnd attached to the gas tank with the help of a clamp. This is where the most interesting part of the work begins. If, on your car, Chinese workers claw to the gas tank at humanity, you will not have problems. Since access to the self-squeezes, compressing the clamp, will be free. And you can unscrew the screws quickly and comfortably. Otherwise, the clamp is fixed as in the photos 3 and 4, have to tinker. And remember the Chinese collector not an evil, warm word ... If a short crosswinter, the head is a cross, the flexible cavity did not help, then there will be a sliding passage in the case. The main thing is to grab the horses of the self-building (photo 5). Fully unscrew the self-sufficiency will not work, but you can weaken the tighten.

After the filter in the clamp began to move (photo 6), you can be taken for fuel tubes. Squeeze the clamps (photo 7) and pulls the tube. Not completely. We also do the same with the second tube. We substitute the tank and turn off the tube from the fuel filter completely (photo 8).

Then it remains only to pull out the old filter (photo 9 and 10). And install it new filterThe arrow on the filter should be directed to the front axle of the car (photo 11).

Tighten the self-tapping screw (passage to help). We connect fuel tubes (Photo 12). When boarding the tube, a click must be heard, which will indicate that the clamps stood in place. After that, trying the tube from the filter. If the tube remains in place, then everything is OK, the tubes are properly fixed on the filter.

It remains only to download the filter and check the tightness of the connections. Turn the key in the ignition lock (until the starter turn on), we give time the pump to download fuel into the filter and create the necessary pressure in the system. After that, turn off the ignition and run the engine engine. We make a control inspection of the fuel filter and tubes that are connected to it.
Is everything dry? Fuel leakage traces not found? If so, you can congratulate you - replacing the fuel filter on the beloved Chery Kimo passed successfully!

When using an article or photographs an active direct hyperlink to the website www.!

For injector engines - namely, this is installed in - it is very important that the fuel used is clean. In this case, the nozzles will not be clogged with mud and gradually collapse and ensure uniform injection of the combustible mixture, and the engine will function in optimal mode and long delight the owner of the car by uninterrupted operation.

To clean gasoline as much as possible and applied. It is performed thin cleaningUnlike the mesh installed in the fuel module at the inlet of the fuel pump, which produces coarse filtering.

What does not mean that the filter is time to change

Do not forget to do it in a timely manner. Otherwise, it will be forced to pump fuel through the scored filter, and therefore it will have to work with an increased load, which, of course, will not benefit him. If the groove is coming from the gas tank, perhaps this is exactly the case. Although pollution can be in other places of the system. First of all, check the mesh rough Cleaningwhich is located in the fuel module along with the pump.

Too early clogging of the fuel filter may indicate the presence of garbage in. In this case, it must be washed.

Some changes in the behavior of the machine can suggest a likely clogging of the fuel filter. Power loss, interruptions in the operation of the motor, car jerking first will be noticeable mainly when accelerating or driving at high speed. Gradually, such symptoms are increasingly will occur at a slower movement.

How it is arranged and where is the fuel filter in Chery Tiggo

On the opposite bases of the cylinder there are intake and exhaust fittings through which the fuel output is carried out. In addition, there is a terminal for connecting the grounding wire (mass).

Since the filter has an unbalanced design, it is impossible to repair it. Consequently, it is necessary to simply replace the new one.

In cars chery brands Tiggo fuel The filter is mounted on the base of the body in the gas tank area to the right of it. Because of this location, you can only get to the filter below. To work with it it was convenient, you can use the lift or observation pit. If there is no possibility, you can simply lie on the rug.

Independent fuel filter replacement in Chery Tiggo

To reset the pressure in the engine power system, you need to start the motor with a disconnected fuel pump And wait until gasoline remains in the fuel ramp.

Turn off the gas station in two ways.

The 1st way is to extract the relay responsible for the pump start. It is in the fuse box under the hood on the right side of the car

The 2nd method is to disconnect the connector with the feed wires in the fuel module. To get to it, you need to throw back backseat And raise the upholstery of the floor. Under it, detect the lidh cover under which the fuel module is located.

After removing the chip with the wires, you thereby devent the fuel pump.

Before disconnecting the chip, do not forget to remove the minus wire with the battery.

Now put the gearbox lever on the neutral and use parking brake. Run the motor. After a while, when the fuel remained in the system, it will stall.

Turn on the starter for a couple of seconds to equalize the pressure in the pipeline, return to the relay place (or connect the chip) and you can proceed to dismantling the fuel filter.

1. Squeezing the retainer, remove the tip of the fuel line from the outlet. The latch can have a serious resistance, then use the appropriate tool, such as a screwdriver. If the tip fails to shift the wrench as a lever.

2. Do the same on the opposite side of the filter.

3. Disconnect the ground wire from the housing.

If you want to replace ground wire, unscrew the head bolt to 10, which it is attached to the body.

4. Pull the device from the holder. To do this, you need to break the spring retainer.

5. Memontize new element in reverse order. In order not to make a mistake when installing, focus on the arrow on the device case, which indicates the direction of fuel flow.

Sometimes the arrow can show an incorrect direction. To find out exactly where the entrance is where the outlet is inserted into the hole of the fitting a long thin object, for example, a nail or a piece of wire. In the outlet, it will stumble on a rigid obstacle. There will be no such obstacle at the entrance.

Hose tips wear up clicks.

Check the tightness of the connection when the engine is running. If you notice the leakage of gasoline, try connecting the fuel lines again. If it does not help, change the seals in the tips or completely hoses assembly. Keep in mind that hoses that are used in the engine power system are manufactured by special technology from materials resistant to lubricant and gasoline. Avoid using random tubes that are simply turned up. This can cause problems with the functioning of the fuel system, and sometimes even lead to a fire.

Do not chase for cheap

But manufacturers of cheap fakes are saved not only on the case. In the filter element, they use thin, fragile paper, which poorly cleans gasoline, passing a lot of dirt into the fuel ramp. It happens that it is simply rhat, and then almost no fuel is served on the nozzles. The nozzles scored by mud will immediately affect the stability of the functioning of the power unit.

Want to avoid similar problems - purchase devices made by a reliable manufacturer.

If you want to extend the operating resource of the filter

Avoid using old gasoline storage cans. There may be a rust on their inner walls, which will eventually fall into your gas tank.

Do not be lazy from time to time to get from the gas tank

I decided to replace the fuel filter on my Chery Tigo, but I estimated that there is no store with spare parts for China. There are still shops designed for foreign cars, but everything concerns the Chinese have even consumables order and wait for a week.

I went to a regular auto parts store, that is, calculated for domestic auto industry. And here is not a filter than no worse and the more no longer differ in constructively.

The replacement of the fuel filter on Chery Tigo easily can be produced in garage conditions. Replacement takes no more than 20 minutes. Question price: ~ 200 rubles.

Replacing the fuel filter

1. Install a car on the lifting box (or call on the observation hole);
2. Find a filter. By car, Chery Tigo, he is located in the Renobook area (in front of him on the right side) and is attached to a plastic clamp;
3. Turn off the tube from it and using screwdrivers to dismantle the filter;
4. Install a new one, given the direction of the shooter on the filter with respect to the tubes;
5. Scroll the car key until the fuel injection. It is necessary that the filter starts to function. Repeat the procedure 3-5 times and after already start the engine.

Symptoms of worn filter

1. Jerks when driving at high speed (more than 90 km / h);
2. Caressing the engine;
3. Insufficient power and "aggression" of the car while pressed on the accelerator pedal.