Lifan Solano. / 620. Check and adjust wheel installation angles

Verification and adjustment of wheel installation angles are necessary to ensure good stability and car handling, as well as uniform wear of tires during its operation. Verification and adjustment of wheel installation angles are performed on special stands according to instructions for their operation.

The inconsistency of the actual values \u200b\u200bmeasured by car, the control values \u200b\u200bspecified in the specifications due to the wear and deformation of the parts of the suspension, the deformation of the body.

A warning

Replacing or repairing the parts of the suspension can entail a change in the angles of the wheel installation, so checking the angles of the wheel installation after these works are required.

The angles of the installation of the front wheels:

the angle of the longitudinal tilt axis of the wheel turn

cross-tilt angle wheel axis: Look in the vehicle specifications

the corner of the collapse : Look in the vehicle specifications

convergence : Look in the vehicle specifications

Rear wheel installation angles:

the corner of the collapse : Look in the vehicle specifications

convergence : Look in the vehicle specifications

Wheel installation angles Check on a car with a ballast weighing 70 kg on each front seat, with half-fuel tank filled with half-fuel, normal tire pressure, in the absence of excessive wells in the suspension nodes.

After installing the car onto the stand, immediately before checking the angles, the "Lodge" suspension of the car, applying two to three times the force directed from top to bottom, first rear Bumper.and then to the front. The wheels of the car must be located parallel to the longitudinal axis of the car.

Checking the angle of installation of the front wheels, first determine the corners of the longitudinal and transverse tilt axis axis of the wheel, then the angle of the collapse of the wheels and the last turn of the wheel alignment.

The angle of the longitudinal tilt axis front wheel educated vertical on the side of the side and line passing through the middle of the top support of the telescopic rack and the center of the sphere of the ball support attached on the lower lever.

Cross-tilt angle of the axis of the turn of the front wheeleducated vertical on the sight of the front and line passing through the middle of the top support of the telescopic rack and the center of the sphere of the ball support attached on the lower lever.

The angle of the bells of the front wheelsit is characterized by the deviation of the middle plane of rotation of the front wheel from the vertical.

Note

Adjusting the angles of the longitudinal and transverse tilt axis of the axis of rotation, as well as the angle of the columns of the front wheels is not provided for by the design of the car. With the deviation of these angles from the nominal values, replace damaged and deformed parts.

The convergence of the front wheels is the angle between the plane of rotation of the front wheel and the longitudinal axis of the car. The forward wheel alignment is regulated by changing the length of the steering.

Rear wheel installation angles can be adjusted during operation.

The angle of collapse of the rear wheels is characterized by the deviation of the middle plane of rotation of the rear wheel from the vertical. The angle of the rear wheel column is regulated by the rotation of the adjusting bolts of the upper transverse lever to the body bracket and to the rear transverse beam.

The rear wheel alignment is the angle between the rear wheel rotation plane and the longitudinal axis of the car. The rear wheel alignment is regulated by the rotation of the adjusting bolt located with inner Control lever.

To install the glass on the front door of the car Lifan Solano, it is necessary to pre-remove the door trim. In this photo report, it will be shown how to disassemble the door panel and the glass installation with your own hands.

To begin with, we remove the speaker - the squeezer: it is removed easily, in the upper corner we insert a flat screwdriver and turn it as if you turn off the bolt and clip scores perfectly, then we pull out and pull out at the top

Attention! Screw the tape with the tape in order not to damage the LCP.

Carefully pull for wiring, there will be a chip, disconnect it, but you can not disconnect and put on the torpedo

Attention! Self-tapping screws are different, so do not confuse them when assembling.

Pay attention to how the plug opens. It opens only on the one hand, on the other hand, you do not need to go there and remains.

Next, you need to dismantle the armrest, on the other side that closer to the hinges are slowly inserting a screwdriver and turn to jumped out a little, then I pull further up and at the end after 2 clicks you can still raise it and pull it towards the loop

After that, I pull in the direction of the loop and withdraw the armrest, then pull out the cable

Approximately so

Further remove the trim, where the tape is there clips, we take the same screwdriver and in these places we sweep up, beginning from the bottom, after all the clips are smaller, it will be possible to raise a little on the bottom.
There is no clips along the glass, the lining just sits in the groove.

After the removal will be like this

Then we unscrew the armrest holder, the screws are all different not confused! There will be so

Further remove the door opening handle, I drag on myself from the side of the cables a little further pushing into a dol door to the side of the cables (to remove all the cables do not need them at all better not touch you just need to make a little more hole in the cellophane

Then, remove the cellophane along with some shine or dust collector, well, if you can, you can shoot separately, then you can smoke 2 third-party scotch

Now, unscrew the glass here

Here on such clips the glass is holding

Now we insert the glass from the top to the bottom, then a little, as if on the break, turn its edge, the one that is thinner at the bottom, omit and insert the glass into the guides. If the glass has been broken, then clean the guides, since there remains fragments and glass does not climb. You can also lubricate the slider. After put the glass in place, screw it up. To easier to fasten the glass through the hole, make such a trick.

Removing and adjusting headlights, substitution of a lamp of close and distant light

In fact, at least some car needs permanent maintenance. It concerns this and headlight adjustments, also disassemble them. This approval is fair for all cars, including Lifan Solano.which has become popular with us in our country.

Removal of fleece head lighting

In order to remove Lights head lighting Lifan Solano, you need to perform several standard actions on this method, which we currently see. Situations in which it may be necessary to remove the headlights for the purpose of its disassembly or detecting a malfunction:

To begin with, it is necessary to dismantle the decorative grille of the radiator, which will allow us to get to the fastener mechanism. After which you need remove the inner part of the front wing panel from the other side with which it should be removed headlight. Next comes ceremony front bumperwhich also needs dismantling.

We carry out dismantling of design elements

Now you can proceed to the direct removal of the entire headlight headlamp with a solid block. In order to do this, you will need to unscrew the three mounting screws, two of which are located on the top of the headlight, and one on the bottom, from the wing side. Next, we carefully disconnect the bracket, for which a small effort may be needed. Also, you do not need to forget about electrical connectors that feed on the lighting appliances. After their neat shutdown, you can proceed to the residual dismantling of the headlights.

After dismantling the elements of the body, you can proceed to the dismantling of the headlight itself

Despite the fact that, almost everything, work has already been made, there are cases that it is necessary to get to the label to replace it. Replace the nearest lamps and far Light Lifan Solano is a fairly simple task. To do this, it will be necessary to remove the sealing cover from the headlight block by defining it throughout the perimeter. Next, there comes the queue of the spring retainer, after dismantling which it will be possible to reach the very light bulb of the near light. Its immediate replacement is no different from the replacement of a regular lamp, so that this action does not make sense.

If you are faced with the task of replacing the standard optics by Biksenon, then study the material: we install Bixenon in the headlight with your own hands.

If you are faced with the task of replacing a long-lit lamp, then it will be necessary, after pre-removing the sealing cover, the same remove Spring locking mechanism, which will allow us to get to the lamp. Its replacement occurs on the same principle.

Also, sometimes it is necessary to remove the light bulb that indicates the rotation of the car. Her dismantling is no different from the above-mentioned actions to replace the rest of the lamps. After that, it will be necessary to collect the entire design back and install the headlight block in place.

Adjust headlight headlamp

Depending on the operating conditions, as well as for natural reasons, it may be necessary to adjust the front headlights. For this, it will be necessary to prepare a car with the help of appropriate cargo, as well as finding a suitable place for this with a smooth surface. As a rule, adjustment is best on special stands that allow you to easily implement this difficult task. However, you can perform adjustment at home.

Lifan Solan's headlights

We restore the transparency of the head Lifan Solana.

Replacing Middle Lights on Lifan X60

Description.

only specialized equipment will allow adjustment in the best possible way.

Preparation

The first point can be considered the direct preparation of the car. This set of actions includes an inspection of the body and headlights themselves for the presence of curvature, which could arise after shocks or any other deformation effects. It is desirable that fuel tank It was completely filled with a flammable, in order to ensure optimal "waving" cars.

Also, the manufacturer advises check the oil level and, if necessary, add it to the full level. The same, you will need to do with liquid in the cooling system. After that, check the tires for the subject right level Pressure. The whole set of equipment for car service, including a jack, a spare wheel and tools that you take with you constantly, should be in your place in the trunk. But all other items from the trunk will need to be removed, so as not to create an excessive load that is not characteristic of the normal state of the car. Also, you will need to ask a person to sit on driver chair. If there is no such possibility, then you can replace a person with a suitable weight.

Now it has come to the cerebral preparation to all further actions. They include the supply of cars in a sufficiently dark place so that the Light Light Light is clearly visible, and was at a suitable level, namely on the boundary of the world. It is located in the place where the light is visible under the line, and there is no.

you can use the garage door or the house wall

Remember that the car must be in a completely equal position. It is about the central axis of the machine to be located 90 degrees in relation to the wall, on which the level of lighting will be performed. The distance to this wall should be exactly three meters. To accurately check the correctness of the machine, it will be necessary to shift it up and down so that the suspension does not change its position in the future. Also, prepare a pure white sheet of paper with a size of 2 * 4 meters. It is necessary to create a light screen.

Vertically, in the center of the screen, draw the line exactly in the middle. It is necessary to make this line in the center of the axis of the car. Also, we draw a horizontal line, above which the central part of the light should not rise. In addition, there should be two vertical lines on the screen, which will indicate on the central axis of headlight headlights, relative to the left and right edge. The intersection with the horizontal line should occur in the place where the central part of the headlight is located.

Direct adjustment

Adjust Lifan Solano headlights are not difficult. To begin with, you need to know that checking the headlights can be very difficult at the same time. Therefore, it is necessary to do this alternately, simply disconnecting the power of the headlight, which is currently not checked. However, it is possible to use this and a simple cloth, which is covered inactive headlight. Nevertheless, it must be remembered that a special vinyl plastic is used as a material for the manufacture of headlights, which cannot withstand high temperatures longer than a few minutes. And since the headlight lamps can produce quite a lot of heat, then you can keep them with no more than three minutes in a row. After a few minutes of cooling when the light is turned off, the operation can be repeated.

The second point in the list of our actions on adjustment will be the launch of the motor with maintaining the number of revolutions at the level of one and a half thousand per minute. Now you can turn off the headlights of the headlight to check the boundaries of light, which should surely go into the boundary specified on the sheet. If you have noticed small deviations from the desired level, then you need to adjust. Its essence lies in a simple turn of the adjusting screws. One of them responds to the vertical axis, and the other is behind the horizontal. In the case of turning the first of them clockwise, the light will be raised a little, counterclockwise - a little lowered. If you need to adjust the horizontal axis, then for this you will need to scroll the screw clockwise, which will lead to the removal of the light beam to the left. After scrolling counterclockwise, the ray will be shifted to the right. For all these operations, an ordinary screwdriver is used.

Thus, adjusting the headlight light Lifan Solano. It may be quite an easy task for most owners of this car.

Rule Repair Repair for Lifan Solano

Lifan Solano is recognized as one of the most high-quality cars. He has good appearance, and comfortable and wide seats, both for the driver and for passengers, allow you to feel very comfortable in the cabin. This car is ideal for reasonable people who have to often be driving because it is intended for more or less suspended and safe driving.

Steering Rake by lifan car Solano, like all other details, is not eternal and has a shelf life, so after a while there may be certain problems. Leaks, etc., and this directly affects the quality of driving.

Steering rake. one of the most important parts of the machine responsible for the ergonomic power transmission from steering column on the wheels of the car.

Symptoms of problems

Steering rake. One of the most important parts of the machine responsible for the ergonomic transmission of power from the steering column on the vehicle wheels.

Read the same:

Signs of the malfunction of the steering rail can be various noises in the pump of the hydraulic amplifier, cutting the thread, "feed" on steering wheel, bad steering wheel control. It takes much more effort to rotate compared to a working mechanism, as well as increase the gap (backlash).

In all of the above situations steering Reika Must be repaired or replaced. Of course, in this case best option will be full replacement steering rack, but it will cost quite expensive, because because of high cost This part most of the owners of this car prefer to resort to repair.

Lifan Solana Replacing the steering rack

Repairs steering rack on the Lifan Solano..Repairs steering rack on Lifan in St. Petersburg. Our service centers provide services.

Read the same:

Repair of the steering rail Lifan Solano. Repair of the steering rail Lifan Solano in St. Petersburg.

site where the seals for reques Salted steering shaft top 19355.5 (100 rub) Two sidelines.

Errors and repair

The steering rail, as well as on other cars, is a power element of the steering mechanism, which evenly distributes the power coming from the steering column to the wheels. That is, the driver's force controlling the steering wheel is transferred from the steering column steering, and then through the steering thrust on the rotary mechanisms that are controlled directly by the front wheels of the machine.

Leakage of the steering rack.

Often leakage in the steering rack is detected when the car costs some time in the parking lot or elsewhere, and after the car has been turned off, there is a puddle of the leaked oil. With a similar problem, the driver arises a feeling of "heavy wheels".

The most common causes of rail damage in this case are damage to integrity or simply an inefficient installation of anthers, which entails the occurrence of corrosion processes, damage in the form of small and large scratches due to dirt, dust, water and other garbage on the outer surface of the steering shaft of the rail.

Read the same:

In such unpleasant situations, you may need: replacement or additional seal of the anther, the installation of new sealing rings, bushings or seals.

Exterior view of the gap. Clearance of the steering rack.

In this case, the defect can be determined visually. A visible gap is formed on the steering wheel. This problem requires a thorough test check. steering rack, implying its disassembly and diagnosis, as this may indicate not only on the formation of the clearance of the rail itself, but also for a malfunction of the steering column. Repair mainly consists in replacing faulty and worn-out components, followed by checking and, if necessary, their additional adjustment.

Pressing, giving a roll.

The driver in such a situation is experiencing a feeling of return on the steering wheel. This is most often caused by various mechanical damage or wear of the steering rack components (clamping mechanism, sliding sleeves, etc.). This defect is eliminated by replacing worn items to new ones.

In case of any failures, it is best to contact the specialists who know the causes and methods of eliminating the car steering rack.