Tuning car salon do it yourself: species, materials and procedures for performing work. Exclusive car interior with your own hands with tuning how to make a car cozy

the main / Battery

For the transformation of the car's interior there are many ways. And this is done primarily not to make originality, uniqueness and individuality of the car, not to stand out from the crowd, but to provide additional convenience and comfort on the trip.

It is for this that there is an internal tuning. Specialized centers are engaged in the modernization of the cabin: replacing finishing, painting, hauling, as well as installation additional equipment. But it can pour out in a round sum, and not every driver can afford it. If you wish, you can improve the interior with your own hands if you follow some rules.

Before proceeding with the work, you need to decide which elements of the cabin require refinement, and what results do you expect from modernization. Scripping trimming, vibrating torpedo, insufficient lighting - all this strains, interferes and causes additional negative emotions from the driver and passengers. For trips to bring only pleasure, and not irritation, proceed to the interior transformation.

Where to begin?

To modernize the interior decoration, it will take some free time, financial resources, perseverance and desire for a positive result. Next, it is necessary to dismantle the seats and the ceiling trim, remove the upholstery of the doors and torpedo, i.e. Maximum free interior. If you can, then you can insulate the wiring in the car, so that it is damaged.

Noise insulation

Foreign noise arising from the operation of the engine or suspension, interfere with the driver and adversely affect the concentration of attention. There are many sound insulation materials for the car on the market, but we need not only to reduce the noise level, but also to eliminate the vibration. Therefore, it will have to buy not only noise insulating material, but also vibroplast. An alternative can be the purchase of a universal more expensive material 3 in 1, which combines the necessary qualities. This stamp material throughout the cabin, and also pay attention to the floor, partition between motor compartment, wheel arches. The application of the mounting hair dryer will make it easier for you. When work on noise isolation is over, you can think about music. It's time to improve the quality of the speaker system if you have any complaints. It is necessary to do it before changing the trim, because then it will be quite problematic.

Salon covering

Cozy and comfortable salon - this is the secret of the popularity of representative class cars. Once inside such a car, you forget everything in the world, dissolve in the ocean of bliss. You can admire the brilliance of the parts and the interior trim. Materials are so pleasant to the touch, that you want to constantly touch them. Want such comfort? It is quite real, and it is not necessary to buy a premium car at all, it is enough to simply change the lounge of the cabin. Even the most broken interior will be transformed and becomes again attractive and cozy. The touch of the cabin gives stunning results, especially if it is leather, Alcantara or Suede. Alcantara is a new popular synthetic material, very interesting, looks at the touch resembling suede. In addition, this material is much cheaper suede and skin, but in quality absolutely it is not inferior. Denim, velor, velvet, silk, but they are not very practical to use them to be used to leave them very practical for the skimming, are considered very beautiful and high-quality materials.

The presence of foreign squeaks on the side of the skin can be a consequence of the gap between the trim and the metal case. This can be easily eliminated by placing a layer of foam rubber in five millimeters. The same can be done when installing a torpedo, the main thing is to clearly fix and clamp all the mounts.

Modernizing the chairs

It's easier and cheaper than just change covers. If the means allow, you can completely change their upholstery, it will increase their wear resistance and give them the style and originality. The most expensive pleasure will be full replacement on more prestigious chairs.

Lighting in the salon

The problem of many cars is insufficient interior lighting. And this is a lack of not only cars of medium and economy class, but also some expensive models. But do not get upset! This is fixable. If you are "friends" with soldering supplies, you can easily change the lighting: regular lamps are replaced by LED. And in the dark day in the cabin will be much lighter!

Often drivers do not like and lighting dashboardIt can also be replaced by LEDs. The work is not difficult, on the shoulder and nonprofessional, but will require concentration and special care. Choosing lED lightening, Think, what color will it be? Of course, I want to be bright and light in the cabin, but in the dark, the person's eyes are very sensitive to bright colors. Therefore, try to avoid especially bright shades, experts are recommended to look at green or dark red.

Modernization of the salon - of course, not the first need, but, you agree, it is much more pleasant to ride comfortably. Especially if you spend a large amount of time on the road. And my own masterfully, the separated salon allows him to be proud of himself and its car. Comfort, comfort and pleasure, not stress and tension must accompany you on the way. After improving the cabin you will feel at home. Some effort, dedication and these tips will help transform your car inside, and the result will justify all the funds spent.

The machine for many people is not only transport, but also a means of expression. The tuning of the cabin suggests a number of works aimed at improving comfort. Among other factors affecting a person who is in a car is the condition of the surfaces of the chairs, panels and other elements. An unusual coating of interior details makes it attractive for visual perception and tactile contact.

Classic is considered to be tuning the car's salon with skin of a thin selection, which is extremely pleasant to the touch and look. This material is widely used to finish the instrument panel, steering and gear lever, as well as doors upholstery. Such a car is comfortable during long trips in all weather conditions: hot summer or frosty winter day.

The specified type of tuning salon is one of the most expensive, due to high prices for natural skin. To work with it, special skills and special preparation are needed, but also the result is worth it. The car literally is transformed and goes into a higher class. At the same time, there are other ways of tuning salon, which are becoming increasingly distributed in the Australian Environment.

Main types of tuning car salon

One of the main reasons that encourages the driver with their own hands to pump a car and is the possibility of its maximum individualization. Main types of tuning car salon:

Taking surfaces using natural and synthetic materials.
Sewing covers for chairs and car sofas (tuning of the seat of the car).
Installing additional equipment to ensure the comfort of the driver and passengers.
Installing backlighting in the car.
Tuning steering wheel.
Noise insulation of the cabin and so on.

Hauling cabin can be both complete and partial. In the latter case, the work is carried out on separate items and elements: steering wheel, seats, door panels, consoles, handles and CAT lever cover. The tuning of the seat of the car is one of the most common types of tuning, especially among the owners of the car with a light salon, since it quickly fits dull, shakes and every spot in sight.

Great importance are high-quality and original accessories for tuning car salon, they are used to emphasize the profitability of changes. Each device and item is carefully selected in accordance with the selected stylistics. Tuning a standard car interior requires fancy and ideas about the properties of the materials used. It is important to achieve the correct combination of the textures of conjugate surfaces.

Materials and accessories for tuning car

Standard interior even business-class machines decorated with expensive skin is still deprived of individuality. Modern materials for tuning car salon make it difficult to make it even more comfortable, but also personify it. The nomenclature includes coatings of various colors, such as cost. A decorative fabric is widely used for car ceiling hawk, which includes the following types:

floss;
alcantar (artificial suede);
carpet;
jacquard;
velours.

Selection of material for self-tuning car Salon It is carried out on the basis of the financial capabilities and personal preferences of the owner. Velvet artificial suede, natural car leather or tissue must match the overall style of texture and coloring.

In the interior decoration, the carbon is often used for the machine from it, the original inserts are made to cover the details. Material is distinguished by ease and strength of a piece of metal. For the manufacture of parts, high-quality tools and work skills will be required. During tuning carbon, a variety of decorative designs are made.

However, because of his high cost and fast fading, many motorists prefer to use carbon imitation, for example, vinyl film under carbon. Below in the figure you can see the mirror attached "pseudo-carbon".

Some motorists prefer such a method of finishing internal surfaces as flocking that gives high quality coating. The spread of technology promotes simplicity and cost economy.

Flocking car interior with your own hands: order of work and tools

Flock is a chemically treated textile, a flocked surface velvety to the touch. Such a coating is obtained by "stacking" fiber flock into glue. Flocator electromagnetic field charges particles and they, having received an electrical charge, perpendicularly stick to the prepared area. Flock is resistant to wet cleaning, does not fade and has a noise insulating effect.

Flocking technology can be performed in a garage or domestic workshop. Flocking the car's salon with your own hands complete or individual elements is carried out using the following tools:

painting brush;
primer automotive;
glue special composition;
koler and Flock;
electric machine for applying material.

Sequence of floccovation work with their own parts of the interior details Next:

It is performed degreasing an element and applying several layers of primer. After drying, it is processed by shallow emery paper.
The item is lubricated with glue with a wide painting brush. You need to apply glue without skips and if possible evenly.
Flock surface finish. To implement this process, it is necessary to use a flocator capable of covering a large area of \u200b\u200ba complex configuration in a short time.
The coating is applied without a break and, not paying attention to the fact that individual porks do not fall on the place intended for them.
The excess flock is blown away using an industrial dryer with a cold air flow.

At the end of work, the surface is dried at a temperature of 20 -22 ° C for several hours. Flock application allows you to update the interior of any car, including with big mileage. Make an attractive salon will help such a procedure as a hauling with artificial or natural material. Flock coating work can be performed without attracting specialists at home.

Tightening the ceiling car lounge with your own hands

In machines with a large mileage, many elements come into disrepair from time. Self-drying of the car ceiling opens the ability to change damaged or severely contaminated upholstery. At the same time, accuracy and thorough followed by step by step leadership.

Tightening the ceiling of the car car is carried out in an electrified garage box and provides the following steps:

Dismantling of an old coating, which is used as a template for performing material marking.
Removing the remnants of glue from the ceiling with a solvent and brush, grinding the surface by sandpaper with zero.
Pattern composite elements and the connection of them between themselves so that the joints are invisible.
The covered ceiling is fixed along the place using standard locks.
Flocking if desired.

This process for a person who has the skills of such a kind, does not take much time. It is possible to cover the flock of the newly formed surface obtained as a result of the ceiling tightness. Only the operation is performed directly in the cabin, the coating cannot be flexing to avoid cracks. The ceiling, which has a flock coating, looks great and is characterized by good performance.

What smells in the car's cabin? Gasoline, upholstery or other flavors. What can smell? Flowers, sea and exotic fruits. How is it possible? Use the flavor to the car and change the idea of \u200b\u200bthe "life on wheels". Of course, everyone has its own opinion on the need to use automotive accessories. However, the manufacturer worried about creating a cozy atmosphere in each car. Smells can be not only synthetic, but also natural. Stylishly packaged dried herbs or shrubs leaves will greatly cope with their task.

Main destinies

The flavors not only eliminate smells, but also affect the nervous system, and they can even delight the eye with their exquisite or non-standard form. In addition, they are different types:

cardboard is available in different animals, plants or geometric shapes. Their layers are impregnated with aromatic substances that fill the cabin auto with pleasant smells within two weeks. Convenient because they can be changed often, especially since the mount is very simple;
plastic jars and bags are used for filling with fragrant gel or dry granules, powder, salt. The aroma of uniform portions is served in the cab. Gel will serve until two months, since they have the ability to evaporate, and the chalk will give the mood much longer;
decorative puffs with granules (briquette flavors) make the most unique smells, will serve quite a long time. Inside there can be natural spices, grains or impregnated with aromasted pads. Their price is quite high;
flakes with smelling liquid filler, equipped with a special valve, which allows you to adjust the fragrance intensity. This makes it possible not only to choose the most appropriate air refreshment mode, but also economically spend the substance;
fragravized toys that please the eyes, but may distract attention.

In order for the smell to be a secret, models on velcro, which are attached to the seat or in another convenient and imperceptible place. Among the special design developments can be noted spray working on the principle of air freshener. He though it stands on weekly, but also serves a long time.

For salons, where they actively use ashtray, the successful choice will be special aromatic granules, which, mixing with ashes, kill the smell of tobacco. A variety of flavors allows you to choose the one that optimally suits the owner of the car. It must be remembered about the effect of smells on the human body.

Among the manufacturers of this accessory should be noted by Areon, Car Fresh, Eikosha, Diax, Carmate, MEDO.

Noise insulation with your own hands

Modernization of the vehicle salon includes a huge number of changes. Before starting work, it is important to understand what kind of result you want to achieve, it will determine with the color scheme of the interior. It will help you figure out for work. If you are owner domestic car And you wish to make a complete tuning of the car's salon, then, according to the advice of specialists, it is necessary to start working with noise insulation and vibration insulation of the cabin.

For this you need to purchase insulation materials in special stores. It is necessary to start work with full disassembly of the cabin, cleaning it from dust and dirt. Fully removed from the salon the remains of the old upholstery. To obtain a qualitative result, it is necessary to initially glue into one or two layers of vibration insulating material, which will reduce the level of vibration in the car while driving. The next step is the sizing soundproof material also in one or two layers. This will reduce the level of noise and screen in the car while driving. It is necessary to glue the material over the entire inner surface of the cabin, special attention to pay hard to reach places. It is possible to enhance the result to go through a hair dryer of materials.

Next can be proceeded to the salon assembly. For a more dense fit of the elements of the trim use seals. If you are going to tuning and lining the cabin, then it is easier for you to cope with this task in a disassembled form and already squeezed elements.

Tuning smooth surfaces of the car's salon do it yourself

Most often, the inner smooth parts of the car are made of cheap plastic and have a non-primary look. Modernize torpedo, door cards and other plastic elements can be several ways.

The easiest way to tuning the interior of the car is a pasting of carbonic products or vinyl film under carbon. This is not a very labor-intensive process, although it requires extreme care, careful measurement of parts. The film glues is quite simple: it is necessary to clean and degrease the treated surface, punch the film, straightening from the center to the edges of the part with a spatula with a soft tip. For more dense adjustment, in parallel, it is necessary to carry out heat treatment with a hair dryer. It is more convenient to perform such work together. Carbon film sold in different colors, therefore you can combine colors for more original view. For example, to highlight the vehicle or a torpedo handle with another shade and individually. It all depends on the flight of your imagination.

A more expensive version of the tuning of the car's salon is the decoration of the interior elements with the skin or Alcantara - artificial suede. Hauling the cabin of the vehicle of the skin is very expensive. For this you need special car leather, which is resistant to fire, is distinguished by strength and wear resistance. A little economically, the option of drawing parts with an artificial suede, which gives the salon comfort and warm. Work with such materials requires significant diligence and attentiveness and can stretch for a week, or even more.

If you are tired of your ugly smooth plastic surfaces, you can always replace them with skin or rare wood species

The most economical and popular version of the tuning of smooth surfaces of the cabin is flocking. This is a way to finish the car's salon with your own hands using a floc - chemically treated textile. Before flocking, it is necessary to degrease the surface of the product, to work on it with primer and shallow sandpaper. The next step is to apply the uniform layer of glue and finishing the surface of the flock. To do this, it is desirable to have a flocator - a typewriter for its application, which in the shortest possible time will help you cope with the task in even hard-to-reach places. The excess material is blown away with a hair dryer. Details are left for graze for several hours. You get the elements of the cabin that have a pleasant to the touch fabric effect, resistant to burnout and wet cleaning, and also give individuality and comfort to your car.

Tuning ceiling machine with your own hands

An important point with the full tuning of the cabin is upgrading. Most often manufacturers produce cars with trim white color on the ceiling. And no matter how birching your car owner, over time the ceiling flashes and dumps, acquires a reddish shade. For the care of the ceiling, the carpet is most often used - inexpensive and widespread material.

Start upgrading is necessary with removal of the upholstery of the ceiling, it is advisable to do it carefully to use it for the pattern from the new material. Next should be cleaned and degrease the ceiling and the prepared pattern with the help of regular fixators to fix on it. For reliability, you can pre-work the ceiling with glue. It will guarantee more reliable fastening.

To give a more presentable view, you can also use flocking for the ceiling.

Modernization of the seats of the car do it yourself

Tuning car seats is an important component of the modernization of the vehicle salon. In order to improve the type of seats, you can buy new autocuses and, thus, to transform them. And also to improve the type of its car, you can replace the old seats with a nice foreign car with seats.

If you wish to get really unique result, it is better to make a car seat with your own hands.

Most often, eco-button is used for the tank. This is not a very expensive material that has good elasticity and presentable view. Of the more expensive options - the manufacture of covers from automotive skin and Alcantara. These materials are characterized by a longer period of operation.

Deciding with the material and its color, you can proceed to work. Before covering the seating, be sure to dismantle from the car. It is very good to remove the seats from the seats, as it will serve you as a pattern, then it is necessary to mark the markup with the help of a marker and old autocups on the new material and cut all the elements of the pattern. FROM inner Plug is made by foam rubber.

To give a more decent view of the seats of your car Try to drag their skin and embroider beautiful drawings

It remains only to sew prepared elements using strong reinforced threads. In order for the autosewings to have a presentable species, the internal seams are required to straighten, cut into the foam rubber and sneak them with ordinary glue. After drying, the covers are steamed with a hair dryer or iron and dress on the seats.

And some more important points

Almost all elements of the car's salon were tuning upgrades. There are several details left, which will give uniquely to the salon of your car.

For a more efficient look, you need to improve the car's wheel. A more presentable view can be given to him by tosing automotive skin. The tuning steering wheel will look more expensive, will become more pleasant to the touch, as well as thanks to the automotive skin, which breathes, the hands will not sweat and slide on the steering wheel.

As well as the type of outstanding salon can spoil old factory mats that look unprepacently and slaughter. Car floor mats can or buy new ones that you like, or make them yourself from rubberized carpet. It will be the perfect solution to the issue, you can choose the color and quality that will fully fit into the interior of your updated salon. To do this, we use an old rug instead of layout and cut tuning mats for your car.

Alternatively, you can add individuality to the salon using additional lighting elements. LED ribbons On the instrument panels and torpedoes can be a stylish accessory for your car.

Let's summarize

As you can see, the tuning of the salon do it yourself is a real task. You can decorate all the elements of the car's interior without exception. Come up with your individual style and interior and act. It will give you a lot of positive emotions and envy surrounding.

Everyone has an individual taste, and the desire to adjust everything is quite natural. Is not exceptions and our personal transport, Therefore, the tuning of the car's salon is of great popularity in many owners.

Tuning inside the car: where to start?

Sure, appearance Machines is of great importance, but also the driver, and passengers most Time is carried out in the cabin. Thus, it becomes necessary to ensure greater comfort by improving and complex revision of the entire car. In addition, it is also important and a combination of the appearance of the vehicle with its technical equipment. This is what is called tuning.

At the same time, the reincarnation can wear a very different character, and no one can accurately calculate the cost of expenses. After all, for some motorists it will be enough to install some sports accessory in the cabin, for example, the steering wheel. And for others it is important to fully replay the style and design of your "iron horse". In the latter case, of course, only own forces It is unlikely to be limited to and have to turn to professionals. So and material expenses will be much higher.

Tuning car salon - choose a way

To date, there are several basic types of tuning, and the most popular among them is flocking, which implies the creation of a velvet surface. The first cars with such design were created in the United States, however, with the time of the Brazda, the Americans took the Switzerland, and now it is she who leads in this area.

It is also worth paying your attention to the trim of the cabin carbon. This fabric is created from carbon fibers and covered on top of epoxy resin. Its main advantages include impeccable appearance, excellent strength characteristics, despite the pretty low weight, and the ability to create a unique interior, as it can easily recreate any drawing.

In addition, to give a highlight to your personal vehicle, while emphasizing all its importance and solidity can be veneered. This finish will talk about the impeccable taste of the host, because natural tree There has always been, there will be in price. True, it is almost impossible to carry out this work, if you, of course, are not a furniture master. You can make an impression on passengers and original, but here you have to work well.

We make a unique tuning dashboard yourself

In principle, make a good high-quality tuning dashboard and a car salon in specialized firms. But if there is a desire to personally take part in creating the design of your transport, then there are no problems in carrying out this procedure and independently. At the same time it will be possible to save significantly and your money, because services of professionals - the pleasure is not cheap.

For you need the following tool: a flock-machine, a primer for a car, a painting, a painting brush and, naturally, the special store itself. Collect all the above items, you can proceed to active actions. First of all, it should be removed the part being restored and pull it out of the cabin. At the same time, think about it right how it will get up back, because after tuning it is impossible to bend it in any way. Then, clearing the surface, cover it with three layers of the soil, with each layer must dry well.

So the velvet layer as a result was even, before applying the entire listed surface, it is necessary to polish thoroughly.

After completing all the preparatory work, you can freely proceed directly to the flocking itself, for this you need to carefully read the instructions attached to the device. Usually, before this, the glue layer is also applied to the surface, and then it is already processed by a machine. Those particles that are not glued are blown away with a hairdryer, but only with cold air. And layers need to dry in vivo in a well-heated room.

As for the trim carbon and this issue, everything is easier simple. The main thing is to clean the surface of the work being processed and apply the base layer on it. Remember that it should dry at least two and a half hours. During this time, the resin should go to such a state so that when touching it sticks, but no traces remained. Next, gently apply carbon tissue. Her edges need to trim a bit with a margin and, bending them, attach painting scotch. Then let the details dry for six hours.