Warming salon UAZ Hunter. Replacing door seals. Shutters on the windows. What you need for driving a car from Belarus to Russia, the better insulation of the Salon UAZ Buanka

Russian winter is usually very cold time and frost at 25-30 degrees are not uncommon. Therefore, insulate on winter time As follows your car, it becomes a primary task for car owners. This work is not very complicated, but requires certain skills and patience. Solves all the good organization and materials that are necessary for the insulation of the cabin.

Materials for car insulation

Modern professional insulation are very effective, easily mounted, and if necessary, quickly removed. You can warm the car's salon with your own hands using the following materials known and the most demands:

Sequence of the insulation in the car

First of all, choose the material you intend to insulate the interior of the car. For the production of work, you will need the following tools:

• sheet cardboard;
• scotch;
• marker;
• sealant;
• rubber seals;
• screwdriver;
• scissors.

Previously, you need to call for washing and complete the interior cleaning. Then, preferably in the garage, dismantle all the seats, remove the door panels and disassemble the torpedo. All things on the rear shelf must be removed.

After inspection of the body's condition, close all holes sealant. Especially carefully process the place located between the motor compartment and the interior. Remove the stove radiator and seal all visible seams. Change the extensive old rubber seals to new ones.

Starting the processing of the salon for insulation is necessary with the floor of the body. The bottom of the car thoroughly and process the solvent. From cardboard sheets prepare patterns.

Buy a calculated material in the store, plus a small supply. According to the pattern made from cardboard, cut the foam of the desired size. If you have a material without an adhesive layer, then you will also have to buy glue tilitis for connecting the seams of the insulation.

Go to the doors, they are also neatly rinsed and processing the solvent, then cut the holes under the handle. Glue pieces of insulation just like on the bottom. Clips are used to places with a pronounced relief, inside fasteners using furniture brackets.

Installation of thermal insulation on the Machine Machines UAZ

In the UAZ-469, another heater is installed in the winter or replace the standard on the device of high power. It all depends on the finance and taste of the car owner, we advise the heater applied on the KITB brand minibuses.3221-8110010.

If your UAZ is equipped with gas equipment, then gas is fit perfectly heaterBut its power should be at least 2-4 kW. The electronics of this device automatically maintains the temperature mode inside the cabin, but the device must be connected to a specialist.

An additional heater is placed at the rear at the very end of the cabin.

Warm the bottom of the cabin with a warm linoleum or a set from the store designed specifically for the floor UAZ consisting of foil foam rubber. In the same insulation, stop the ceiling of the cabin, sidewalls, door panels and a place near the torpedo. Seals are suitable for all doorways from UAZ Hunter.

Place a warm polymer top instead of a tarpaulin, take away all the holes and slot slits.

Attention! To insulate the Salon UAZ-469 with their own hands, all the above must be done only comprehensively.

By establishing heat shifting on the UAZ-3909 or simply on the "loaf", it is necessary to try not to take a regular ventilation system by making a kind of thermos from the salon. If you accidentally clog the factory ventilation, a large mass of condensate will be formed in the cabin.

The mounting foam is associated with foam plastic covered with foil does not allow heat to leave the cabin and keeps quite a long time, so such a coating fully justifies itself. Another option is to obey the salon with a 4-millimeter plywood or put the porporal of the middle thickness.

A warning! The greater the thickness of your insulation - the less place in the cabin.

So for a little money, it is quite nice to insulate the Salon UAZ Buankka with their own hands.

See how the Salon UAZ Buanka Polyurethane Fiurethane can, on this link:

Heat protection equipment on VAZ family cars

Warming the car inside, we create conditions for reducing the heat transfer and maintain a constant temperature regime in the cabin. At the same time, it is also excellent sound insulation that significantly reduces the noise in the cabin. He insulates him, we see how they stop moving the car's glass, and we feel more comfortable and safely.

Similarly, insulate the salons and other VAZ cars. When traveling in winter time on VAZ 2115, 2110 and prior Many passengers sitting on rear seat, often pay attention to the influx of cold air in this part of the cabin. The fact is that in rear door At the very bottom there are ventilation linings made of plastic. At speed, such ventilation significantly reduces the temperature inside the cabin.

To better insulate the interior, you need to significantly reduce the influx of cold air. To do this, remove plastic lining and exactly on them, cut the desired size with a small margin from the insulation. Special glue material glit on the front side of the lining. The hole under the lining is missing Moviem and install the lining, placed insulation in place. Now the cold no longer penetrates the inside of the cabin, and the ventilation is preserved and does not allow to accumulate moisture and condensate at the bottom of the door.

Equipment with thermal insulation of foreign cars

Budget foreign cars Popular in Russia are distinguished only by better tightness and good stoves. In fact, the insulation is as such, there are no foreign production machines.

To insulate the salon in foreign cars in our frosts must be necessary. If the engine thermal insulation can be solved using a referee, then you need to work with the body. From the insulation, the foam with its adhesive base and foil is best suited.

We remove the decorative trimming of the doors, cut the desired dimensions of the insulation, leave the holes so as not to interfere with moving parts inside the door and glue to the foil part. With the trunk, everything is easier, by the way, there are even places for fastening the insulation. Usually this processing is enough.

If your region has a more severe climate, then the floor can be covered with insulation and puncture the ceiling of the cabin.

On foreign cars you can put in heat from the vibroplast - this material is not only extinguishing the vibration, but also by itself a good insulation. We pave them floor, ceiling, all doors and trunk.

To preserve the heat of the engine, we use the auto tube, although some manufacturers offer a plastic plate to close the radiator, but this is clearly not enough.

In conclusion, I must say that than careful and carefully you have been handled your car's salon, the more comfortable you will feel safer on the road.

Made vibration insulation of the cabin.

Floor amplifiers were covered with anti-corrosion composition based on bitumen. As it turned out, it is not the most the best choice material. Over time, when the composition is drying, its coating has become fragile and mechanically exposed. So that for processing it is better to use another material.

The internal amplifiers were processed by anticorrosive for hidden cavities

The ceiling was covered with water-based composition. Unlike bitumen, it is just intended for internal work. But possesses a very sharp smell that did not destroy the three days.

But after drying, it turned out a very durable and homogeneous layer, which struggled to be offended only with the help of a metal brush planned on the grinder.

As the manufacturer of PRIM-W assured it can easily be labeled noise insulation.
But words - words, and in practice the purchased noise insulating material did not want to be glued to the ceiling by the processed anticorros. Even despite the fact that the surface was carefully degreased.
It is a pity, the material for Shumkov chose a good:

I had to change tactics.
A briquette with stone wool sheets was purchased in the construction market.

Stone Vata. - Heat-sound insulation made mainly from the melt of the erupted rocks. Mineral wool variety. The initial raw material for the production of stained wool fiber is the gabbro-basalt rocks.

Stone wool is a non-combustible material.
Stone wool fibers are able to withstand the temperature, without melting up to 870 ° C. Stone wool does not burn, but at a temperature of 600-700 degrees decays hot dust.
Stone wool products have heat-insulated properties due to open porosity. The coefficient of thermal conductivity of the stone wool is in the range of 0.035 - 0.039 W / m K. Air enclosed in the pores of the wool, has a low thermal conductivity and is in a static state, it is precisely that it determines its excellent thermal insulation qualities.

When working with stone cotton, it is necessary to observe precautions: work in the respirator, in rubber gloves and protective glasses.

The laying technology is pretty simple: mark on the place, cut a knife with the desired sheet size and put it between the body amplifiers.

In the oz cavity is not so deep as the thickness of the stone wool sheet, so one sheet had to be cut into half. It is convenient to do it with a knife and a long metal ruler.

The laid sheets of the insulation are closed, on the floor, plywood regular sheets

And sidewalls - standard upholstery

The back of the body, where the sidewalls curve, has a fairly deep cavity and the layers of stone wool are fit in full thickness.

So, gradually filling all body cavities insulation

And closing the standard upholstery

We process the whole cabin of loaf.

With air intake for additional stove Salon had to tinker.
The fact is that there was an impressive gap between him and the body, through which water could get.

Fastening location did not give proper result.

Therefore, the sealer was cut out of the old insulation. It remained a sticky layer and with its help the sealant was glued to the air intake.

The slot on the street was eliminated.

For the last unclosed cavity of a separate leaf of the insulation, there was not enough, it was necessary to collect a puzzle of cropping.

Final stage. The whole body is insulated.
Vacuuming salon. You can make a wet cleaning :)

Now when tapping on board the car, it is not audible sound canning cansAnd a deaf, quick-tightened sound indicating solid preparation of the car body.

You will need

• - isolon;
• - Penoplex;
• - genuine or synthetic substrate for linoleum;
• - plywood;
• - Penoplex;
• - Fiberboard;
• - fasteners (selflessness, glue);
• - Scotch;
• - scissors, knife, electrolovik;
• - screwdriver or screwdriver;
• - polyethylene film.

Instruction

Remove the linoleum web and inspect the floor under it. If the boards are in good condition, did not rot, insulate the floor, starting from this level. Inspect the doors, and decide what height you can lift the floor so that they are well closed and opened. Put the substrate for linoleum. If you tend to natural and environmentally friendly materials, choose the natural base from the jute fiber. Please note that it quickly grieves and gives dust, it can start mole and other small insects. To avoid these problems, buy isolon or penplex (with foil on one side). Cut them into pieces of the required size, decompose on the floor, glue with scotch all the joints. Then impose a layer of plywood sheets on top and screw everything together with screws. Plywood will provide sufficient stiffness of the design and will not give linoleum to fall.

You can warm the floor from linoleum just plywood sheets. In this case, glue the sheets with mastic or special glue for wood.

Your floors will be very warm if you decide to insulate them with extruded polystyrene foam (penoplex), but learn that it is recommended for facing buildings outside, and when used indoors, it can highlight harmful pairs.

If you decide to put under the linoleum DVP, be sure to carry out waterproofing so that it does not have a swelling. To do this, put the layer of polyethylene film on the floor, then the DVP layer, which is to additionally projected (walked). Top Paul Close another layer of plastic film. In order for moisture to be leaked down, use rectangular linoleum plinths. Thoroughly close the joints between the linoleum sheets, and it is better to choose the sheets of such a width so that the joints are not at all.

If you are not worried about electricity bills - to put a film "warm floor" under the linoleum.

Video on the topic

note

It is not necessary to sharpen under the linoleum slab from the chipboard. Despite the fact that they will give good insulation, when washing the floors and when collecting condensate, when collecting temperatures, chipboard plates are capable of sweeping, which will lead to failures and irregularities on the floor.

www.kakprosto.ru.

The fineness of the selection of the awning on the UAZ 469

UAZ 469 with a removable roof

Today, UAZ cars are in great demand due to their practicality, reliability, in the second way to make anything with them. You can enjoy elevator and the installation of the rear axle, which will turn the usual SUV in a stunning all-terrain vehicle, capable of cope with any tests for strength, and you can proceed to replacing the roof.

It is quite realistic to change the types of the roof of the UAZ depending on the climatic conditions, the profile of the car and the intention of the car owner. But for what is needed awning UAZ 469, what is his advantages?

Back to the category

Brief overview UAZ 469

To deal with the expediency of replacing the roof on the UAZ 469, consider the features of the car. UAZ 469 is a hardy, unpretentious domestic SUV, who first focused on sale in 1972. At that time, practicality was put on the first place, and not aesthetics, so the car capable of driving almost along any road, even the very bad, which has a capacity, easy to use and is quite maintainable, very much appreciated. UAZ 469 was based on the preceding model - GAZ-69, but received significantly best equipment and more modern appearance.

UAZ could not please the perfectly soft move, but he gave much more - the ability to withstand serious loads, which is undergoing a car passing through the blurred roads of the province. It was for this purpose that he was created.

Four-cylinder installed on the car gas engine 2.5 l, with a capacity of 75 liters. from. It is worth noting that the same engine was put in those days on trucks and was called UAZ 452. The engine worked with the usual four-stage mechanical box Gears I. rear wheel drive.

Tental patriot

In 1985, a light stage of restyling passed, while the appearance of the car changed only slightly, but technical filling Well updated. Appeared more strong engine Power of 92 liters. from. Improved thrust and high-speed capabilities, so that the car got a lot of positive responses from the owners.

Both in the first and second generation of the SUV body was offered exclusively in the open form. If necessary, it was possible to purchase a UAZ awning, which would have covered from rain, snow and cold wind.

It should be noted that awning UAZ 469, as, for example, UAZ farmer, poorly protects against adverse weather conditions. Thus, another version of the models arose - with a metal roof. Both modifications have both their advantages and disadvantages.

Back to the category

Types of roof UAZ and their features

On the russian roads You can see different UAZ. UAZ HANTER with a metal roof positioned on the market as a comfort alliance, power and safety. There is also a hunter tilt. UAZ Farmer is covered with camouflaged awning. The roofs have a UAZ Patriot Pickup and UAZ 469. All the options of the roofs are good in their own way, but what better?

Beach version of Hunter

Considering UAZ Hunter with an iron roof, the following advantages can be noted:

• the iron roof makes the car with a hermetic, protected from thieves and bad weather, warm, cozy;
• the iron roof of UAZ Hunter positively affects the stability of the machine, you can not be afraid of steep turns that the roof simply demolish;
• iron roof and trunk - full of compatible things;
• if you wish, you can carry out complete noise insulation of UAZ Hunter and enjoy silence and peace.

Disadvantages of material.

1. Iron withstands many tests, but rust can quickly damage it.
2. The iron roof takes the car, which is why it is noticeably losing in speed. Weight increases for a whole centner.
3. With incorrect installation, noise is often heard.
4. The capacity of the car will be strictly limited, the overall loads of the type of long boards can not be transported.

Quite often you can see UAZ Farmer or UAZ 469, equipped with a plastic roof. Pros of such a design:

• good tightness;
• since the plastic roof is manufactured with a special platform for the transportation of additional cargo, it is universal and very convenient;
• easy installation, light weight, which does not affect the negative way on the dynamic qualities of the car;
• if desired, it can be done in the roof of the hatch;
• unlike metal, plastic is not subject to corrosion;
• as in the case of an iron roof, here you can put the trunk;
• excellent protection against thieves.

And now let's talk about the minuses of the plastic roof. The presence of a special platform for the carriage of goods is well in summer, but in winter and in the fall in it constantly accumulate snow and water, because it is made in the form of a trough. On sudden turns plastic roof unstable. Plastic - unreliable material that is felt right away. The leaks are also a significant disadvantage of plastic option. And the last is a high price of plastic.

Back to the category

Advantages and disadvantages of tent cars

You can hardly find a driver who never met the tilt machines. What are their advantages and disadvantages?

Benefits:

• the car is not lost, there is no extra 100-120 kg, which is good for the dynamics, speed;
• thanks to the tend, it is quite realistic to transport in the car non-standard loads, boards or something else coming beyond the bodies, the main thing is to fix stronger;
• this is excellent option for fans of convertibles;
• if you warm the salon, you will get a very cozy, home atmosphere, which is not in the car with a metal roof;
• low cost.

Pickup tenth

Disadvantages:

• leaks: there is no problem in dry warm weather, better option Not to find, but when the autumn time comes with its endless rains and ice winds, not avoiding trouble;
• it is necessary to carry out insulation;
• externally awesome car looks specifically, what not to everyone like;
• the trunk on the awning is impossible;
• noise while driving.

What is important, awning is easy to open. For the owner, this is a plus, for thieves - too. Therefore, it is necessary to think well before installing the awning.

Pluses and minuses at the tilt roof rore. It should be proceeded from a specific situation, to consider in what capacity the car will be used, what type of goods you need to carry, etc. Buy awning in the store or on the car market. It is easy to order and via the Internet, in our time such a service is very popular.

prouazik.ru.

UAZ 469 - Tuning Salon, photo

Practical and reliable UAZ 469b, which began to be freely sold only after 1991, all suits everyone. A lover of a comfortable active recreation will not even think about buying a UAZ 469, simply because this machine is not intended for comfort. Is it really that, we decided to figure out, considering some options for the improvements of UAZ, aimed at improving comfort in the cabin.

Why improve the Salon UAZ

Because on the Land Rover there is no money. This is the main reason for the improvements of the UAZ 469 tuning of the salon of the photo of which we picked up on the page, is done rather not so to improve comfort, as to improve functionality. The car is used in different ways, and the character of the alterations, which take motorists depends. For Safari, the requirements for the salon will be alone, and for winter hunting is completely different.

Yes, and the budget of tuning is also not rubber, although many, even those who can buy and Rubicon, and the Cherokee, will still improve the UAZ, because the car deservedly enjoys folk love.

Refinement of the Salon UAZ do it yourself

To begin with, it is necessary to decide, and what's wrong with the Salon of UAZ, which requires refinement, and what can be left unchanged, especially if refinement requires serious investments and some special tools or materials. From the point of view of comfort, the salon 469th is a solid flaw. But the highlights that are forced to take for the tools:

In the warm season, the UAZ can still be used as a fan car, and the streams in the disclosures of the cabin can be perceived as exotic. But not in winter. Already a weak car stove is simply not designed for full heating, so it will have to be refined in the first place.

Warming salon UAZ 469

Naturally, the insulation of the cabin makes sense only when the car is not awesome, but with a rigid roof, otherwise there will be no sense from heating. Along the way, you can also hold noise insulation. Mostly noise is published by vibrating panels, so everything that vibrates must be muffled.

This primarily concerns the roof, because its area is large enough, so it will vibrate most. There are practically no other particular large planes without ribs in the car.

The entire cabin, including doors, floors, roof, engine shield, is trimmed first with vibroimol or similar material, which is on sale in bulk. The construction follicate insulation is perfectly suitable. They will be no less effective than special automotive, and cheaper two times. After the insulation of the cabin on the floor is put and fix the aluminum sheet to make it easier to maintain order, and then it looks then the interior according to fashion recent years On polished aluminum, resembling a stainless steel.

Salon for hunting and fishing

Hunting is different, actually, like fishing. If the car is already quite prepared on the technical part, then the trunk can be adjusted for the transportation of inventory. Often hunters make in the trunk. Locks for inventory and weapons to get quick access to it. In general, the fixation of the cargo is a serious thing and it is necessary to approach it. Depending on the road Conditions And the weight of the cargo, it can be fixed in different places, but the center of gravity is desirable to have as low as possible.

Also, it will also be a hatch, which can also be embedded into the roof, pre-insulated so that the condensate is not rested. Also, as in the case of the floor sheel aluminum, all the joints are carefully sealed. As the Oaz salon is quite high, you can make a few shelves with your own hands. IN regular salon There are no places to storing cards, navigation trivia, the same cigarettes. Therefore, a small console above the windshield does not prevent.

Seats and devices UAZ 469

There are no special complaints about the instruments of a car, they can, as they can, and the panel can be seen by stainless steel. It will be harmonized with aluminum floor, however, the effect is solely decorative. Also often put seats from more fitted cars, some salons are suitable at all practically without alteration, as in particular, the salon from Honda CRV. So, if you fully fold the seat, it turns out a huge amount for download.

Even with very small investments, it is possible to lead to the relative order of the Salon UAZ 469, having fulfilled all the work with his own hands. The main thing, not to be lazy, and UAZ will transformed into a comfortable SUV for long raids. Good luck to all roads and light off-road!

Car UAZ-469. Designed for military department. The context of the cabin is actually absent. And the thermal insulation of the cabin too. A typical heater does not cope with its duties, and its noise of its work creates additional discomfort. Countless slots and low thermal insulation of the floor turn UAZ-469. In one of the coldest cars of the domestic auto industry.

Instruction

1. For the insulation of the cabin, first replace the heater to more strongly or install the added heater in the rear of the cabin. The choice of a certain heater depends on flavors, preferences and financial probabilities of any owner of the UAZ. But still you have to change the configuration of the stove. Recommended to choose heaters pretended for installation on minibuses. Say, Kitb.3221-8110010. This brand can be installed as a rod or additional stove. It will excellently warm the salon of a large internal volume, but has quite large dimensions.

2. It will also be suitable for the UAZ independent salon heater operating on gas fuel. Alone from the selected heater model, it must own a power of 2 to 4 kW. Such a heater charmingly harmonizes with the installation on the UAZ of gas-ballon equipment. The superiority of the independent heater is the likelihood of mechanical maintenance of temperature in the cabin. The disadvantage is the difficulty in independent connection.

3. Warm floor. When limited in finance, use warmed linoleum for this. If finance is allowed, acquire a specialized floor insulation kit in a car shop. It consists of a foil layer and a foam layer glued on it.

4. The front panel, doors, sidewalls of the body and the ceiling are improper, by obtaining specialized materials. Establish them is allowed both orosy and in a specialized firm. Doors Equipped with double seals from the car UAZ Hunter.

5. Tarpaulin awning, standard installed on UAZ-469. Replace on a warmed model of more modern polymeric materials. If you probably, order a personal tailoring. In any embodiment of the installed awning, purchase an additional insulation for use in winter time.

6. Seat all the slots in the cabin with the support of the mounting foam or specialized sealant

In the houses with grained heat insulation in winter, it may be uncomfortable in winter, from what to walk is actually in the boots. Linoleum put on such a floor actually does not give the heat insulating result. In order to improve the situation, it is not necessary to disassemble and change the entire design of the floor, it is easy to insulate the existing linoleum.

You will need

• - isolon;
• - Penoplex;
• - Natural or synthetic substrate for linoleum;
• - plywood;
• - Penoplex;
• - Fiberboard;
• - fasteners (selflessness, glue);
• - Scotch;
• - scissors, knives, electrolovik;
• - screwdriver either screwdriver;
• - polyethylene film.

Instruction

1. Remove the linoleum web and look back under it. If the boards in excellent condition, did not rot, insulate the floor, starting with this tier. Look up the door, and decide how much the floor is allowed to raise, so they closed coolly and opened.

2. Put the substrate for linoleum. If you tend to natural and environmentally friendly materials, choose the natural base from the jute fiber. Please note that it is rapidly engaged and gives dust, it can start mole and other small insects.

3. In order to avoid these strokes, you will acquire Izolon or Painoplex (with a foil on one side). Cut them into pieces of the desired size, decompose on the floor, glue with scotch all the joints. After that, impose a layer of plywood sheets on top and screw everything together with self-draws. Plywood will provide contented stiffness of the structure and will not give linoleum to fall.

4. It is permitted to insulate the floor of the linoleum primitively plywood sheets. In this case, glue the sheets with mastic or special glue for wood.

5. Die hots will be warm with your floors, if you decide to insulate them with extruded polystyrene foam (penoplex), however, learn that it is recommended for facing buildings outside, and when using indoors, it can highlight a detrimental pair.

6. If you decide to put under the linoleum DVP, strictly carry out waterproofing, so that it does not happen. To do this, put the layer of polyethylene film on the floor, after which the Fiberboard layer, the one that is worth adding to add (walked). Top Paul Close another layer of plastic film. In order to so that the moisture could not leak down, use rectangular linoleum baselinits. Scrupulously close the joints between the sheets of linoleum, and it is more cool to choose the sheets of such a width, so that the joints were not at all.

7. If you are not worried about electricity bills - to put a film "warm floor" under the linoleum.

Video on the topic

Note!
It is not necessary to sharpen under the linoleum slab from the chipboard. Despite the fact that they will give an excellent insulation, when washing floors and when collecting condensate, when collecting temperatures, wood-chip plates are able to worry, which will lead to failures and irregularities on the floor.

Helpful advice
In order to make the Salon UAZ-469 really warm, use all the above measures in the complex.