Polishing the car with your own hands. Independent polishing of the car body, types of polishes polishing machine do it yourself

A rather relevant topic, because each car owner wants to see his reliable iron friend with a beautiful and radiant pearl samples with an ideal mirror paint coating. It is possible to achieve such success only with high-quality polishing, subject to a good layer of varnish, or acrylic paint. An important factor in the mirror surface of the car is polished after painting.

No painting in the chamber can guarantee a complete absence of dust in the stained surface, and fresh paint or lacquer can lose up to 60% of the shine - there are a number of technological reasons: the quality of the materials used during painting and surface preparation used solvents, humidity, humidity, Drying temperature.

Technology, sequence and polishing nuances

First you need align the surface - i.e. Get rid of explicit gerane, dust, and chatters, if any. It's easier and better to make a large number in 1500. It is better not to use more severe gradation, since at risk, for example, from 1000 sandwich is quite difficult to move, and the layer of varnish it removes good. The question is especially relevant on Kantha and sharp corners - to rinse in such places to paint or soil - in general, a simple matter. To do this, all edging and sharp corners leave for a light circuit of 2000 by the number, or at all 2500. That is, we are cluttered so far only planes.

The degree of "purity" of the surface and its readiness is easy to determine on the surface dried from the water on lateral bribe. For removing the water from the surface, the silicone brush is ideal, however, it is suitable for its absence and the usual wiper brush is suitable - the main thing is not to scratch the body with metal elements. The washed surface, after removing the water, such a "janitor" dries in 15 seconds and when viewed on lateral bribe, there should be no obvious gaps in the inside, coarse tracks from dust, shagreen.

Next need move the surface of the sandpaper With a smaller graduation - 2000. She shoots a layer of varnish, so again we behave carefully on Kantha and corners. It is necessary to climb high quality, so that the risk of 1500 remains, and the surface was more glossy. Abrasive 2500 removes, in principle, traces from 1500, but quite hard, and throw it much longer.

Capacity in 2500 requires special attention. There is a rule - "How Titanic will call, so he sails." Move badly, - it means to get 2 days after polishing a matte machine. The polyrolol very quickly removes the traces of 2500 sandwits and perfectly distributes a well-prepared surface. Giving an extra time for the cloud of 2500, it is possible to save not only the polyrolol, but also a mass of time both on the layout and for an additional coach.

Polish It is better in small areas - if it is a door, divide it visually on 6 parts, and the hood, depending on the size, it is possible for all 20. In small areas, it turns out to achieve a good degree of disengagement much faster. Apply polyrol is best on the surface itself, and circle without turning on the machine slightly swingto prevent it from splashing.

Polishing better cross areas - from top to bottom, and immediately right-left - this will help to avoid incompreporated areas and will prevent overheating of the straight-colorful coating.

As for the edges of the elements bordering the neighboring body details, then caution is also needed at each execution step. When covered, it should be monitored that the beam does not cling to the edge of the adjacent body element, eroding the most cant, to which it has a lot of load during operation. When polishing, a separate attention should be paid to the direction of rotation of the circle.

By polishing the extreme part of the body element, the circle should slip in its direction from the edge of the details, and not to approach it. Otherwise, you can damage the layer of paintwork, and in some cases damage the body and injure yourself. So, polishing for example the back right door, it is better to open it so that the circle does not rub the back of the rear wing. And polishing better upper from itself part of the circle - in the direction of movement clockwise, this part and will be just "slipping" from the door. And on the back wing, polish the bottom, also, with the door open.

In no case cannot hold the circle in one place - otherwise the layer of paintwork is burning, which will lead to the formation of stains, and even up to wiping to the level of soil or even deeper. We also remember about Kanta and sharp corners - they do not davise on them and it is especially not fond of polishing them.

Another nuance that is worth saying is dried polyrolol on the circle, abrasive grains Which without bonding wet composition are capable of leaving scratching divorces on a polished surface, reducing the degree of gloss noticeably. To eliminate their appearance, polishing circle requires periodic cleaning. Specialized stores sell special metallic mechanisms for cleaning them, however, performing one-time work on polishing, you can completely do with the screwdriver - for example, a screwdriver. Slightly clicking on it, when the circle is rotated from itself, the dried abrasive is poured from the composition of the polishing circle.

It is possible to clean the circle with extreme caution, and only in the direction of the circle from ourselves.

Dark colors are especially whimsical to the polishing process - firstly, all the nuances are visible as much as possible, due to its high mirror reflection, and secondly - the effect of the hologram from the use of large abrasive, lack of poly rays, dried polyrol particles on the circle. To remove such an effect, antgologram polyrolol will need. Of course, it will be better to go through the second number of ordinary polyteroli, with a smaller abrasive, and then antigologram. The finishing polyrolol with the prevention of a hologram effect does not have a sufficient abrasive for physical removal of micro-pharmacy, therefore it is recommended to first produce polishing less abrasive polyrolla.

At all stages of machine processing with polyrolla, a soft napkin from microfiber will be required.

It gently removes the remnants of the polyroli without scratching the surface. The dried polyrolol in Kants and the joints of the body elements is very difficult to remove, so it will be advisable to delete it immediately.

Performing the above manipulations on the right polishing - your car will acquire a primordial factory shine, and your saved budget will allow you to buy a good antiradar to the car, or a DVR who will be captured by all the numbers of envy car enthusiasts and simple zooak.

Successful to you polishing the body of your car!

The car body polishing is the process of removing various defects, scratches and dents, which were obtained during the operation of the vehicle. Her functions:

• after polishing the machine has;
• is a mandatory step in preparing a car for sale;
• protects against the exposure to the external environment;
• with the help of polishing, you can remove small scratches from the body, while their depth should not reach the primer;
• it is necessary to eliminate various defects that arose after.

To qualitatively independently polish the car, you need:

1. Finely abrasive skurt partially remove paint coating.
2. Implement restoration polishing with special abrasive paste.
3. Give the body brilliance with protective polishing with non-abrasive paste.

Polishing process

Conditions

To prepare the car in advance everything you need. Pick up a closed, clean and well ventilated room. In the process of work, a huge amount of dust will be distinguished, which immediately needs to be removed.

Note that when performing this procedure, it is strictly forbidden to enter the room of direct sunlight. Otherwise, polishing components dried very quickly. At the same time, do not forget to take care of good lighting.

Before starting the procedure, it is necessary to align all available dents. For surface polishing, glue with special scotch chips and deep scratches. For deep - process them in a special way. You also need to take all rubber and plastic parts, including headlights.

Choose polyroli

Before choosing a polyroli, it is necessary to estimate the condition of the paint coating. If the car, and you want to give her shine, use the means that do not have abrasive elements. For the restoration of the lacquer coating, the body of the polyrolol will also have to handle the body. If there are many defects on the body, it is better to use colored polyroli.

All polishing agents for their consistency are divided into types:

• pasty - due to their thickness are very convenient to use both on vertical and horizontal surfaces. Their cost is much higher, but with their help, a huge color depth is achieved;
• liquid - apply only for the hood, trunk and roof, as they have a very liquid consistency. Safe, do not cause rapid wear even with long-term use;
• aerosols - their composition includes a small amount of polyrolol, but they are convenient for use.

It should be noted that the properties of the used funds are directly dependent on their composition. The protective polyrolol with wax and silicone is very well applied, but after two or three months the polishing procedure will have to repeat, as this means is quickly washed off.

Polymer polyters are considered more durable and qualitative. They can be applied every six months, while the result of polishing is long saved. True, their price is much higher. As for the process of application, it is more time consuming and long.

We carry out the polishing process

Simple polishing

It is performed as the final stage when the body surface is already smooth and without any defects.. First you need to apply a small amount of polyroli on the surface of the car. This can be done with a napkin. After that, you need to wait a while so that the polyrol rip. When it looks like white raids, you can start polishing to shine. In one place, perform from 10 to 20 circular movements. Follow the instructions of the polishing agent used. To secure the result after 4-6 weeks, this procedure is better done again.

On video - car body polishing:

Deep polishing

Deep polishing machine is used to remove various defects from the body surface.

To begin, you will need sandpaper P2000 and P2500, rubber bar and water. With their help it is necessary to pass large scratches. These include those defects that you can feel your finger. Then you need to conduct a polling procedure using the smallest emery. For better results Conducting movements can be used. Ultimately, you must achieve a homogeneous surface. If the scratch is very big, you can mentally divide it into small parts and take turns to polish each of them. Sometimes for deep polishing takes more than 12 hours.

The next step is the use of a special polishing machine. Before that, moisturize your car and apply the required amount of polishing agent to the equipment. First, carry out the procedure at the highest mode, to evenly distribute the paste. Then you can accelerate and start performing polishing. Move the machine smoothly, without lingering for a long time in one place. Make sure that you do not overheat the processed item.

Types of polishing

Abrasive polishing body carried out on the lacquer coating that has a non-ideal appearance and a huge amount of defects. At the same time, scratches should not reach the soil. First, the sweatpad varnish is removed, and then the polishing process is performed.

On video - abrasive polishing:

Soft polished Used for intact varnish coating.

Protective polishing car divided into two types:

• surface - is carried out before selling;
• protective - protects against the effects of adverse weather conditions.

Summarize

With the help of polishing, you will return your car an excellent appearance. If you exercise, then save cash. The polishing process is not relieved, and if desired, every motorist can cope with this.

Content

Initially body new car Covered with a special layer of protective varnish, which is called paint and varnish coating (LCP). Over time, he starts to lose his shine, becoming more and more muddy. In addition, scratches and traces of external factors appear on the body surface, the number of which is constantly increasing. In order for the body to acquire the past, you need to resort to the polishing of the car, the cost of which is quite accessible to many machine owners, the main thing is that it is correct and competently fulfilled.

What is polishing

Under such a process, as polishing the car, it is implied to give the vehicle of the initial appearance with the elimination of all small damage, scratches and removing the smallest irregularities of the LCP. In addition, the new layer is designed to protect the surface of the machine from the effects of external factors. The auto-polyarol used for this purpose is abrasive, wax, synthetic. The choice of a specific option depends on the state of the painted surface.

For what is needed

Auto phase is needed not only to impart the surface of the car of the former shine and aesthetics, but also to remove any visible defects. Such a procedure is a necessity, because Through microcracks in the upper layer, various aggressive substances fall on the metal. Their impact on the material leads to the process of corrosion. Foci gradually increase, and when the car owner will notice the formed defects, then he will have to spend great to the localization of the corrosion process. It turns out that polishing the machine is needed and as prevention.

Types of car polishing

Before placing the body surface to return the gloss, check out the polishing options. Depending on the purpose, it can be cleansing, soft, reducing, protective. As for polishing paste, it is selected in accordance with the state of the paintwork. For example, if vehicle Almost a new and its body cloudy only slightly, the optimal choice will be a polyrolol for the car body at home with a low content of abrasive particles or without them.

Cleansing

Raise the body of a vehicle from scuffs, holograms from poor-quality polishing, cobblers, small scratches will help cleaning car polishing. It is necessarily carried out before applying any complex protective coating, for example, ceramic, quartz or liquid glass. This option is ideal for new cars or cars in good condition. More information about features:

• In what cases is used: for cleaning from all types of pollution, small scratches, holograms.
• Features: For the procedure, bezabrasive and finely abrasive pastes are used.
• Advantages: Does not affect the thickness of the LCP, is performed on average per day.
• Disadvantages: It is used exclusively for cars that are in good condition or with a very soft varnish.

Soft

Deciding to order children, i.e. Cleaning and restoring the car, pay attention to the soft polishing, which is universally performed in the car service. This variety of polishing is considered the most careful. At the same time, it costs somewhat cheaper compared to the application of abrasive composition, but he penetrates the LCP shallow. Often used by owners of cars japanese productionFor which the delicate and not too durable layer of varnish is characteristic. Characteristics:

• In what cases is used: for vehicles with barely noticeable imperfections of LCP, low mileage.
• Features: is a transitional option between abrasive and basic reducing polishes.
• Advantages: The upper layer of varnish is not thinned.
• Disadvantages: Applicable for machines only with a more or less good body condition.

Restorative

Under this type of polishing, it is implied to remove the part of the protective varnish to save the body surface from small scratches, web, which are formed from the sandblasting effect. In addition, it is widely used to give the machine of the initial shine. For this purpose apply various options abrasive pastes and polishing circles with varying degrees of dies. After restorative polishing, it is recommended to make protective so that the gloss effect is preserved for a longer period of time. Read more about Technology:

• In which cases are used: to eliminate all types of dirt, deep scratches.
• Features: Means can be used, both with fine and medium grain.
• Advantages: The impact on the thickness of the LCP is minimal, suitable for old cars.

Protective

To give the hood and the rest of the body elements, high-quality and aesthetic species must be resorted to the complete protective polishing. With professional approach and availability required toolsSuch a technology allows the brillium and gloss to the velocity and the gloss, and reliably protect its body from environmental impact. This contributes to an increase in the operation of the machine. This polishing is applied manually:

• In which cases are used: to protect the machine from the negative impact of external factors.
• Features: For performing, bassabosive polyters based on synthetic materials or waxes are used.
• Advantages: protection against ultraviolet, resistance to the appearance of holograms, oxidation, to most chemical compounds.
• Disadvantages: High cost.

How to polish the car

The polishing process can be mechanical or manual. In addition, there is a contactless method, the use of which assumes the presence of a special microemulsion implemented in production relatively recently. Before polishing the car with your own hands, prepare a suitable agent. It can be a car, gel, pasta, etc. Perform a procedure indoor with ventilation hood and intense light sources on the walls and the ceiling. Next, follow these steps:

1. Wash the car, dry, after which you remove traces from anticorrosive or insects and immersible bitumen stains with special tools, For example, White Spirit. After making sure that the car is clean, degrease the surface with an anti-rigoric agent.
2. Take the skin, a bottle of water and gradually, without clicking on the grout of the treated surface to a matte state. Grinding paper Take as thin as possible - not gross P1500 and P1200. Behind it for 5-10 minutes before work.
3. After grinding, do not forget to clean the working surface from dust.
4. Take the grinding machine with a circle rigid (white) or medium stiffness (orange) and medium-trimmed paste. Do not forget to mix the circle.
5. Apply a paste on a polished area using special napkins from microfiber.
6. Start polishing, starting a process with more low speed, gradually increasing them to 1-1.5 thousand.
7. After completing the procedure, check the result of the work performed. Then you remain to wash the surface with soap or moistened by its degreaser.

Car polishing agent

To polish the car of black, red, white and other colors it is very important to choose the optimal agent. One of the secrets of a successful result will be to how literate will be the choice. This will help you the following rating, which includes one of the best polyterols for the body of the machine:

Car polishing price

In view of the fact that the polishing of the car is a complex and time-consuming process, entrust it better professionals. An independent approach in the absence of the necessary experience can apply a car even greater damage. Save on the polishing of the car, contacting the masters, if comparing prices in different workshops. To find out how much the car polishing in Moscow costs, check out the table:

Video

As we know, the paintwork of the car is subjected to a strong effect of external factors. This is I. permanent drops Temperatures, and small road dust, which seems to be chosen in the paint, thereby forming microcracks.

Thanks to the polyterol, the LCP appears a thin protective layer, which prevents the fading of paint and the appearance of various deformations on it. If you regularly produce polishing, you save the first this species A car that was given to him by the manufacturer, without resorting to painting services for a hundred.

Types of polyrollas

Before answering the question of how to polish the car with your own hands, consider the varieties of protective funds. They are divided into two types. Protective polishing can be both with teflon and wax basis. The difference between them lies in the duration of the protection function. For example, Teflon polyters can not lose their properties up to 7-8 miles. At the same time, wax analogs are cleaned already in the second or third time.

How long does this procedure take?

As practice shows, a simple passenger car is manually from 30 to 50 minutes. The presence of special machines with nozzles can speed up this process by 2-3 times.

Regular performance

How often do you need to make such work? Specialists recommend polishing the car body at least 1 time in 3-4 months. If you are very rarely using the vehicle (for example, only on weekends 1-2 times a week), it is enough to work 1 time in half a year. Is it possible to polish the car more often? Of course, it is possible, it does not harm it. But every time you need to wash the car thoroughly in order to remove the remains of the wax or teflon substance. In any case, it is impossible to rub polish in any way. So you only lose the paint coating of the car - the small particles of dust and sediments are handled in it.

How much does it cost in car service?

For a hundred for such services, about 1 thousand rubles will be requested. If we take into account the fact that the price of one Tube Polyrol Troops costs up to 100 rubles, it becomes clear that it is much cheaper to do this procedure. Moreover, one bottle usually grabs 2 times.

Abrasive polishing

A lot of workshops advertise such a service as abrasive polishing. It is also called restoring. This type of work applies in cases where the car needs to eliminate microcracks, scratches and other minor paintwork defects. Unlike simple protective, such polished requires more time and availability of special tools.

This work consists of several stages: LCP preparation (this is removing the upper coating layer) and aligning scuffs.

It should be borne in mind that, together with scratches, this polyrolol removes part of the painful coating itself. Therefore, one car recommends that no more than 10 cycles of abrasive recovery are recommended. If the digit is greater, instead of paint and varnish polyrolol will already be removed soil.

How to polish the car with polishing machine at home?

As not strange, polishing is quite realistic to do at home. To do this, it is enough to have an electric drill or a small grinder and a special nozzle. The latter is called a polishing block. Also in stores you can purchase ready-made machines for such work, however, the result of the work will be the same with the grinder, which is with such a device.

The essence of professional polishing is as follows: During friction, the block heats up the paint coating, while the polyrolol is filled with its particles all the small irregularities and slots on the body.

Preparatory work

Regardless of whether you will use special tools during work or an ordinary rag, the process of preparing the car is the same. It includes several stages:

1. Full car wash. We definitely do it before polishing the car. After painting, part of the paint and varnish should dry in the sun.

2. Removing various spots from insects, which has been resin and dirt on the LCP near the wheeled arches. Here you can use various chemicalssuch as White Spirit, non-Stermetrians or gasoline.

3. Degreasing the surface. It is likely that in small areas of the body after the use of detergents, traces remained. Such places usually have a muddy view of the sun. In order for the polyrolol to keep on the body as long as possible, the White spirit or other chemicals should be treated (but not abrasive) the entire perimeter of the paint coating. By the way, in the auto shops you can purchase a means for deep cleaning Hi-Gear. It is intended for degreasing such surfaces. To use it is very simple. First you should shove the bottle well, then apply a substance on a soft piece of the vet and evenly rub throughout the body area.

As a result, you will see how the car will noticeably hang outwardly.

Polishing

So, how to polish the car after the preparation of the LCP? To begin with, the vials themselves with the means. Polyrols can be both in tubes (thick mass) and in plastic jars (mixture of mass with liquid). In the latter case, the bottle should be carefully shaken before use.

Next proceed to work. The polyrolol on the body should be applied in series, sections of 50x50 centimeters, ranging from the front bumper and the hood, ending with the trunk and roof. By the way, the roof can be divided into 4 parts and polished in several stages.

How to apply a mass on the body surface, define themselves. This can be made like small circular ribbons and in the form of points. If your polyrolol is refilled in a metal tube, in no case do not touch the surface of the LCP - it remains gray prints, which are very difficult to remove.

Equally applying a mass on the body, wait time (usually 1 minute) until it gets up. After that, take into hand a soft rag and rub the mass until it turns into a transparent shiny film. How to polish the car machine? The process can be said similarly. Only here instead of rags you use a drill with a nozzle. Using such a tool, it is important to remember that the polyrolol should be frozen with a uniform force. Do not put pressure on the body with all your weight, as you can damage the paint coating itself. If you want to know how to polish the car with a machine, remember that the tool should work all over the perimeter, where it is applied this mass. Drive it to the left and right, up and down, or handle the circular movements.

During the work, do not let the possibility of polished. Remember that the dried mass will not turn into a thin film - it simply scatters pieces to the other side.

Polyrol shrinkage period is 24 hours. At this time, you can travel on the car, but it is best to refrain from them for a day so that the protective film is finally strengthened on paint and varnish coating Body.

How to polish the car after painting?

It is worth noting that this type of work is somewhat different from the usual application of the protective mass. The fact is that polishing after painting includes a whole range of work using special equipment and automotive cosmetics. It is done on the 3-4 week after painting. It is necessary for lacquer donkey and not formed failures during polishing. Such work also includes elimination different scratches and irregularities that could appear from high humidity or negative environmental impact. By the way, before polishing the car, it is necessary to grasp it with a fine-grained skin. The technology of these works is very complex, so it is not without the hands of professionals.

Conclusion

So, we found out how to polish the machine manually and with the help of the machine.

As you can see, the process is not very complicated and not very long. Therefore, it makes sense to independently master the skills for using the polyrolol, and the saved 3-4 thousand spend on a couple of new tires, pads or other parts.

Car polishing with their own hands - an important part of the car care process, because During the operation of the car on the housing, both dirt is formed, poorly climbing during car washing and small scratches, significantly spoil the appearance of the machine.

Scratches can be formed both on the body itself and on the glasses and headlights, which are also exposed to small particles: dust and dirt, falling on the car at high speed, scratching it. In this case, it is necessary to carry out polishing, and since this procedure is expensive, when carrying it out in the car wash services, we will try to polish the vehicle.

Polishing headlights and glasses

Before starting polishing the body, it is worth cleaning the headlights and glass from small scratches. In the process of driving, glass and headlamps suffer from small particles of earth, sand, dust and so on. One year or two after buying cars, headlights and glasses are covered with such a layer of small scratches, as if they are in a translucent film. Polishing the headlights costs 1 time in 1.5-2 years, and it is this stage that is the first if the body polishing is performed for the first time.

Standardly before polishing there are our preparatory stagewhich includes washing the headlights / glass, drying and gloaching adhesive protective tape (construction tape) around the perimeter of the headlight, in order not to damage the car body. For polishing you will need:

• polishing machine;
• abrasive felt or foam circles (3m) with graininess in 600, 1000, 2000 and 4000;
• polyrolol;
• fixing varnish;
• soft rag.

Headlight polishing is carried out without the need for their removal, which the process itself is much simplified, the headlights are removed in the case when the internal polishing requires. Cost of a set for polishing 15-20 cu - It will be enough for 6-8 times to use. Most headlights B. modern car It is made of plastic, so expensive means by type of paste with diamond dust will not need, unless of course you are not the owner of elite cars. Polishing windows auto requires the use of special coarse-grained pastes with diamond dust - the main difference in polishing.

The process of polishing the headlights is as follows:

Preparatory stage before starting polishing the body

Before polishing the body, approximately the procedure is made as before polishing headlights and glasses. So, before polishing the car body, it is necessary to clean it thoroughly, and before the level of absolute, hygienic purity. In order for the process to go smoothly, it is recommended to polish in a closed, clean and well ventilated room. It is also worth delighting the room from direct sunlight, otherwise the polyrolol is quickly seized. Therefore, the room in which the car will be polished must have good artificial, preferably luminescent, lighting.

It is worth knowing that polishing the car whose body has damage or dents, it does not make sense, since the plot with dent, after polishing, will look a spot, which reduces all the works. Therefore, with such body defects, they should be eliminated. Deep scratches and chips should be stuck with construction scotch, as they are processed according to a separate principle. Plastic parts, as well as headlights, edging windows need to be stuck with a construction tape, in order not to damage these body parts.

Tools and Inventory for Polishing Body

Polishing body - the process is not complicated, but rather laborious. At best, it will take 1 hour, at worst - much longer. So, for polishing will be required:

Grinding machine - the most important tool for polishing. So, you need to choose a grinder with turns from 1000 to 3000 per minute, the device from the battery is not worth it, because The charge is enough for a short time, and the battery is very quickly in disrepair. In rare cases, an electric drill is used for polishing, but in this case there are many twisers with a selection of special grinding, adapters, and so on.

• Polishing circles with graininess in 600, 800, 1000 and 2000, 2500 and 4000 (i.e. full set). Circles are felt and foam, the numbers mentioned earlier mean the rigidity of these circles. So, the tougher is used to polish paste, the hardness should be a polishing circle.
• Soft rag for the final stage of polishing;
• Foam;
• Construction Scotch;
• Polyrolo, paste;
• Emery paper with graininess in 2000 and 2500.

After purchasing all the above, you can begin the body polishing process.

Polishing body

Body polishing is two species - simple and deep polishing. Their important difference is the use of different pastes, polyters and circles for polishing.

A simple polishing is used if there are no deep or medium in the depth of scratches - otherwise, there will be no effect from polishing. So, the phased process of polishing looks like this:

It is worth noting that the simple polishing will support the body in a brilliant state of only 3-4 weeks, after which the procedure needs to be repeated.

Deep polishing applies case when the machine has deep and medium in depth of scratch. In this case, abrasive polishing with disks from 600 to 2500 are applied. The body polishing the body with deep scratches is almost completely different from surface polishing and consists of the following steps:

It is worth noting that the deep polishing process takes a lot of time - 10-12 hours, so it is better to break the car to the conditional 3-4 polishing zones before polishing.

Polishing scratches

Many motorists in the appearance of small or medium in depth of scratches believe that it is necessary to completely polish the car in a deep way, however, it is often not that it makes sense, because You can level scratch in 10-15 minutes as follows:

• Wash out the part of the car where scratch is located with a 646 solvent. This is done for the fact that often what we consider scratch is the paint of another car.
• If the first stage is not successful - you need to sweep the sector of tape-bright or sandpaper with a shallow grain of 2000, moistened in water. Quite often, small scratches disappear after 15-20 rates.
• After the grout, you need to take the G-3 polyrol and a rag with microfiber and to lure the polyrolon area with a scratch to shine.
• We polish the paste G-10, which will make the item more brilliant and remove the divorces after the previous stage.
• We rub with a preservative polyter and rags with microfibra area. All, scratch polishing is completed and the car in perfect condition, as if only yesterday was bought in the cabin.