Recently acquired a "grant" in the configuration "Norma". The immobilizer is activated, that is, the lamp does not light up at the start (basic instruction, p. 10-11). As they have activated, already found on the Internet. I think I would have coped. And then what should be done if I want to turn it off? I heard such a sequence also there, but they know it only on the service.

Expert answer

The Following Two Tabs Change Content Below.

Expert on Lada cars with many years of experience. I own a car Lada Grant, collect Corches on the basis of "Priory". Sometimes I stay with overnight in the garage. My wife is jealous of me more than women.

First specify the code

1. Ignition include and turn off the "red" (learning) key. Lamp flashes;
2. Within 6 seconds (a new version - 2 seconds) establish a "black key", the ignition includes. 3 signals sound;
3. There are two more signals, for 6 or 2 seconds, the ignition is turned off, and the key is replaced by the training. Include ignition;
4. Three signals will follow, then two more;
5. Turn off the ignition, wait for a single signal. Flash frequency lamp doubles;
6. Include ignition. SignalizerCheck must burn;
7. When the signaling device goes out, go to step 8;
8. Enter the number: first - short pressing on "gas", then one long. You need to set six digits (from 1 to 9);
9. In the last step with a long press, the Check signaling device does not go out. Turn off the ignition - the input is completed.

If step 8 immediately press the pedal for a long time (more than 5 seconds), the "old code" is erased and not used. Know about it.

Educational key - right

Engine starting

1. Turn on the ignition without using the label;
2. Wait for the CHECK alarm;
3. Perform code input as discussed above (step 8).

Explanations: Short Pressing - no more than 3 seconds. And a long-term - until the sign of the alarm, although it does not go out when entering the 6th digit. And if so, it means that everything is done correctly.

Immobilizer work scheme on video

This is the most primitive way to disable immobilizer. If we talk exactly, then this is not a shutdown, it is his "destruction".

Immobilizer Lada Granta
Immobilizer

Activation of immobilizer

Immobilizer - anti-theft car system, device to prevent engine starting. Many drivers either do not use it, even if they are provided on their car, or even do not know about it. But security is not something worth neglected, so the owners of Lada Granta should be familiar with the principles of work such a useful device.

When using the ignition key driver, the immobilizer is identified in the controller using its code each time the engine starts. If the code is faithful, there will be no obstacles to the operation of the motor, in the event of a discrepancy, blocking is turned on. The only substantial minus of the immobilizer is if it fails, you will not be able to start the car until the broken device is fixed. In this case, the old code of the immobilizer needs to be removed and write to the new controller. When buying Granta's Lada, the immobilizer is activated in the vehicle preparation items for sale, in the presence of the future owner. The buyer's refusal from this procedure should be recorded in the service documents, assure her signature and seal of the seller, as well as the signature of the host of the acquired vehicle.

Lada Granta is equipped with two ignition keys:

The first, marked black, worker. It can be equipped with a remote control. This key removes the ban from the start of the engine. It is used for an ordinary daily ride.

The second, marked with red, training key. He not only removes the ban from the start of the engine, but also includes the mode of training of an electronic immobilizer and a door block control system. It is strongly recommended to use it only if necessary and stored in reliable place. In case of loss of the training key, the warranty service of your anti-theft system ceases to be a headache of the dealer.

Activation of Immobilizer Lada Grant

Activation "IMO" lies in the following stages, everything is detailed !!!

So let's start:
1. Close all the doors.

2. Turn on the ignition with the red key (key key), wait more than 6 seconds. (If the system is not activated, then a control lamp of the immobilizer will light up in the instrument panel in the instrument panel.)

3. Remove the learning key. The machine should be frozen with a frequency of 5 times per second.

4. Quickly (within 5-6 seconds) Turn on the ignition with a black key (working key)

5. Immobilizer must submit 3 pisctions + 2 pages. If the sound was not:
- the time interval was exceeded (repeat from the beginning)
- the working key is already trained with another system
- Immobilizer is faulty

6. Turn off the ignition and pulling the black key.

7. Quickly (for 5-6 seconds) While the machine blinks on the Ignition Tutorial

8. Sound signal 3 pisch + 2 pages.

9. Off. ignition. Educational key do not take out !!!

10. Sound in the form of 1 pisch.

11. Quickly (within 5-6 seconds) Include ignition for 2-3 seconds!

12. Off. ignition. Keep the key in the castle

13. A beep signal in the form of 3 pages + goes out the machine. Do not remove the red key. (When working with some controllers, the light bulb must occur and the outlet of the buzzer 3 sound signals occurs already when the ignition is turned on. In this case, it should still be off. Ignition and wait more than 10 seconds.)

14. We are waiting for more than 10 seconds.

15. Remove the key !!!

It should work from the first time. If not, then repeat from the beginning.

Conclusion: Successful activation "IMO", the icon machine with the key stopped lighting up when the ignition is turned on.

Immobilizer

Activation of immobilizer

Immobilizer - anti-theft car system, device to prevent engine starting. Many drivers either do not use it, even if they are provided on their car, or even do not know about it. But security is not something worth neglected, so the owners of Lada Granta should be familiar with the principles of work such a useful device.

When using the ignition key driver, the immobilizer is identified in the controller using its code each time the engine starts. If the code is faithful, there will be no obstacles to the operation of the motor, in the event of a discrepancy, blocking is turned on. The only substantial minus of the immobilizer is if it fails, you will not be able to start the car until the broken device is fixed. In this case, the old code of the immobilizer needs to be removed and write to the new controller. When buying Granta's Lada, the immobilizer is activated in the vehicle preparation items for sale, in the presence of the future owner. The buyer's refusal from this procedure should be recorded in the service documents, assure her signature and seal of the seller, as well as the signature of the host of the acquired vehicle.

Lada Granta is equipped with two ignition keys:

The first, marked black, worker. It can be equipped with a remote control. This key removes the ban from the start of the engine. It is used for an ordinary daily ride.

The second, marked with red, training key. He not only removes the ban from the start of the engine, but also includes the mode of training of an electronic immobilizer and a door block control system. It is strongly recommended to use it only if necessary and stored in a reliable place. In case of loss of the training key, the warranty service of your anti-theft system ceases to be a headache of the dealer.

Activation of Immobilizer Lada Grant

Activation "Immo" lies in the following stages, everything is detailed !!!

So let's start:
1. Close all the doors.

2. Turn on the ignition with the red key (key key), wait more than 6 seconds. (If the system is not activated, then after 5 seconds in the instrument panel, the immobilizer control lamp will light up.)

3. Remove the learning key. The machine should be frozen with a frequency of 5 times per second.

4. Quickly (within 5-6 seconds) Turn on the ignition with a black key (working key)

5. Immobilizer must submit 3 pisctions + 2 pages. If the sound was not:
- the time interval was exceeded (repeat from the beginning)
- the working key is already trained with another system
- Immobilizer is faulty

6. Turn off the ignition and pulling the black key.

7. Quickly (for 5-6 seconds) While the machine blinks on the Ignition Tutorial

8. Sound signal 3 pisch + 2 pages.

9. Off. ignition. Educational key do not take out !!!

10. Sound in the form of 1 pisch.

11. Quickly (within 5-6 seconds) Include ignition for 2-3 seconds!

12. Off. ignition. Keep the key in the castle

13. A beep signal in the form of 3 pages + goes out the machine. Do not remove the red key. (When working with some controllers, the light bulb must occur and the outlet of the buzzer 3 sound signals occurs already when the ignition is turned on. In this case, it should still be off. Ignition and wait more than 10 seconds.)

14. We are waiting for more than 10 seconds.

15. Remove the key !!!

It should work from the first time. If not, then repeat from the beginning.

Conclusion: Successful activation "IMO", the icon machine with the key stopped lighting up when the ignition is turned on.

The composition of the immobilization system:

Note: In the execution of "Lux" immobilization system further interacts with the remote control system.

Immobilizer signaling device:

1. It burns for 15 seconds after turning on the ignition, if the KSD "is not trained".
2. Flashing for 20s after turning on the ignition with a frequency of 1 Hz, if there are errors or malfunctions in the immobilization system. (Optional zoommer signals are additionally fed, see "Soundless Malfunctions of Immobilization System")
3. Flashing with a frequency of 5 Hz under the learning procedure. (see "Activation")
4. Flashing with a frequency of 10 Hz upon completion of the learning procedure (see "Activation")

In cars with SDU ("Lux"):

1. Flashing with a frequency of 1 time in 3 seconds in the mode of protection
2. Flashing with a frequency of 2 Hz when removing from security in standby opening the door (before opening any door or to auto plane for protection).

Immobilization system malfunction sound signals:

If the immobilization system is faulting, the buzzer sound signals are fed to the flashing of the alarm. Sound signals are fed to the 10th and 20th second after switching on the ignition.
1 Signal - no key transponder.
2 signals - no connection between KP and COMS.
3 SIGNAL - the identifier of a read key is missing in EPROM KP or KP is not trained.
4 signals - KP cannot decrypt the query of the CSDD ("Alien" COMS).

Intensification of the work of the immobilizer (training)

Attention! The keys before starting training should not be in one bundle, so that in the transponder reading zone there was no more than one key.

1. Sit on driver chair And close the driver's door.
2. Include ignition by learning key (with red insertion on the end). Make sure that in the instrument combination, the symbol of the car with the key (the immobilizer indicator) caught fire.

Attention! If the immobilizer is previously this car Already trained, the immobilizer indicator should not burn. In this case, this learning procedure can only be carried out using the "its" learning key that was previously
Trained on this car.

3. Turn off the ignition, the immobilizer indicator must be filled with a frequency of 5 Hz, remove the learning key from the ignition lock.

Attention! The flashing of the indicator in the learning process indicates the successful passage of the learning procedure.
Termination of flashing means that the procedure is interrupted.

4. Turn on the ignition to the operating key. Three beeps of the buzzer should be sounded and after about 6 seconds two more sound signals.

Attention! The time interval between the ignition shutdown by the learning key and turning on the ignition is not more than 6 seconds, if this time has been exceeded, there will be no sound signals, and the flashing of the immobilizer indicator stops. In this case, you should repeat the procedure with P. 2 . If all repeated attempts turned out to be unsuccessful, then the working key is either
Faulty, or was previously trained on another car.

5. Turn off the ignition and remove the work key from the ignition lock.
6. If you do not need to train additional working keys, then go to p. 7 . If you need to train additional operating keys, then perform p. 4 and 5 For all learned working keys. Then go to p. 7 .

You can train up to four operating keys.

7. Turn on the ignition by the learning key, no later than 6 seconds after turning off the ignition (the immobilizer indicator should flash). Three beeps of the buzzer should be sounded and after about 6 seconds two more sound signals.
8. Turn off the ignition. Do not remove the learning key from the ignition lock. After 6 seconds, a single buzzer signal should be sounded and the immobilizer indicator will switch to an accelerated migration mode (10 Hz).
9. No later than 10 seconds after the zoommer signal, turn on the ignition, the three sounds of the immobilizer buzzer will sound, and the immobilizer indicator goes out. In cars with SDUs ("Lux"), turning pointers twice will be blocked and the short signal of the Klason will sound (completion of the training of the radio channel).
10. Turn off the ignition, remove the learning key.
11. Check the work of the immobilizer. Include ignition by the operating key, the immobilizer indicator should not flash or burn with permanent light. Clear engine trial, the engine must start.
12. This is completed on this procedure for learning and control, the system is properly and functioning normally.

Attention! If at what either stage the learning procedure was interrupted, then it must be reinstalled and to complete without changing the components of the system: the ECD controller is an immobilizer - code keys.

In summary (Procedure control is sufficient to lead on the indicator):

1. Close the driver's door.
2. Turn on the ignition of the learning (red) key.
3. Turn off the ignition and remove the key. The indicator begins to blink with a frequency of 5 Hz.
4. Quickly (for no more than 6 seconds) Include ignition working (black) key.
5. 3 pisch -\u003e 6 seconds -\u003e 2 pits.
6. Turn off the ignition and remove the key.
7. If you need to train other operating keys, then repeat items 4 - 6 for each operating key (not more than 4 keys).
8. Quickly (for no more than 6 seconds) Include ignition by learning (red) key.
9. 3 pisch -\u003e 6 seconds -\u003e 2 pits.
10. Turn off the ignition, the key does not remove. 6 seconds -\u003e 1 squeak. The indicator begins to blink with a twin frequency (10 Hz).
11. Enable ignition. 3 pisces. The indicator goes out. Training is completed.
12. Turn off the ignition.
13. Check the activation of the immobilizer. Turn on the ignition by any key if the indicator does not light up when the ignition is turned on, the immobilizer is activated. We produce a trial start of the engine.

Restoring the performance of the immobilization system when replacing the elements of the system.

1. When replacing the CSD-A (on a new or "non-training") system performance is restored to the implementation of the learning procedure.
2. When replacing the immobilizer controller (instrument combinations), the system's performance is restored to the implementation of the learning procedure without changing the remaining elements of the system.
3. Replacing a list of registered working keys is carried out by conducting a learning procedure.
4. When replacing the learning key, the system's performance is restored by the implementation of the learning procedure, subject to the replacement of the KSD-A to the new ("non-training") or cleaning ("disappointment") EEPROM KSD-A. \\

Immobilization bypass procedure for car Lada GRANTA.

This procedure is used to start the engine without reading the coded key in the event of a malfunction of the immobilizer. Immobilization crawling algorithm is recorded in the non-volatile memory controller of the engine control system (COMS). You can use immobilization bypass procedure only after writing an individual numeric code (password) to the CSDD. The car owner can change the password unlimited number of times, performing the procedure for entering a numerical code in the CSDD. Initially, the CSDD is supplied with the lack of a programmed password, i.e. Bypass procedure is prohibited.

1 Entering a numeric code in the CSD
1.1 Prepare a set of ignition keys consisting of a working (with a completely black head) and a training (with insertion of red).
1.2 Close all doors of the car. Insert the learning code key into the ignition switch. Enable and turn off the ignition. The system status alarm (LED) must flash quickly.
1.3 While the flashing of the LED has not stopped (within 6 seconds), remove the training key from the ignition switch, insert the work key and turn the ignition. The buzzer of the anti-theft control unit must issue three beeps.
1.4 Wait for the ignition on before issuing a buzzer of two more audio signals, then turn off the ignition.
1.5 While the flashing of the LED has not stopped (within 6 s), remove the work key from the ignition switch, insert the learning key and turn on the ignition.
1.6 The buzzer should issue three beeps. Wait for the ignition turned on before issuing a buzzer of two more sound signals.
1.7 Turn off the ignition, without removing the learning key, wait until the buzzer is given sound signal. The LED should be twice as fast at the same time.
1.8 Include ignition by the learning key while the LED flashes. Lamp " Check Engine"(CE) should burn.
1.9 Wait 1 minute until the CE comes out.
1.10 Enter a six-digit code number consisting of numbers from 1 to 9 (the minimum possible number 111111, the maximum possible 999999).
1.10.1 Entering the number of code: Press until it stops on the accelerator pedal, hold the pedal in the pressed position no more than 3 seconds. The number of clicks on the accelerator corresponds to the insertion input. The CE lamp lights up, confirming each press.
1.10.2 Recording the digit of the code: Press the accelerator pedal and hold down until the CE lamp will go out (≈ 5 seconds). Release the accelerator pedal. *
1.10.3 Enter the remaining five digits of code, performing the actions of P.P. 1.10.1, 1.10.2 Another 5 times in a row.
1.10.4 If after entering the last digit of the code and holding the accelerator pedal is pressed for more than 5 seconds of the CE lamp:
- does not go out, it means that the password is completed correctly;
- Begins to flash with a frequency of 1 Hz, it means that an error occurred when entering the password. You need to turn off the ignition and repeat the procedure again with paragraph 1.2.
. Attention! If after entering the number of the code and holding the accelerator pedal, in the position of more than 5 seconds, the CE lamp begins to flash with a frequency of 1 Hz, it means that an error has occurred when entering the numbers (for example, pressed to the accelerator more than 9 times or exceeded the waiting time (1 minute) never without pressing the accelerator). You need to turn off the ignition and repeat the procedure again with paragraph 1.2.
1.11 Exit the password recording mode in the CSDD occurs when the ignition is turned off. If the password is not completed to the end, it is not saved
1.12 The prohibition of the procedure for bypassing immobilization occurs if after execution of paragraph 1.2 ... 1.9, click on the accelerator pedal and hold it down for more than 5 seconds. If the immobilization procedure is prohibited, the CE lamp will be buried constantly when the ignition is turned on all the time before starting the engine.

2 Passage
2.1 Include ignition. CSDD prohibits the start of the engine (the immobilization function is enabled). Ce burns constantly.
2.2 Wait 1 minute while CE does not go out. If this did not happen, it means that the procedure for bypassing immobilization in the CSDD is prohibited.
2.3 Enter your password code, according to claim 1.10 (see above).
2.4 If after entering the last digit of the code and holding the accelerator pedal is pressed for more than 5 seconds of the CE lamp:
- It does not go out, it means that the code is entered correctly, you can run the engine.
- Begins to flash with a frequency of 1 Hz, which means that the wrong password is entered, the bypass procedure must be repeated, turning off the ignition, starting with paragraph 2.2
2.5 If the bypass is completed correctly and the engine started, the CE lamp goes out after the engine is started.
2.6 CSDOs operates in immobilization mode to its complete shutdown, which occurs after 5c after turning off the ignition. The engine can be launched again if no more than 5C has passed since the ignition is turned off. If more than 5C has passed since the ignition shutdown, the engine start becomes impossible and it is required to repeat the bypass procedure again.

ATTENTION! If you, before the activation of the immobilizer, alarm system was installed with auto-start, then after activating IMMO, the autorun will cease to work.
If your immobilizer is activated before installing the alarm, and you want to set an alarm with autorun, then you need to additionally purchase:
- Immobilizer crawling module,
- Chip working key and teach it.

Dealers do not like to activate immobilizer on new domestic cars. There are several reasons for this.

The reasons for which the staffing immobilizer does not activate

1. Just laziness.
2. Someone demands money for this and do not want to do free.
3. Other dealers do not want to activate it, as they will have to perform the procedure for "bypassing the immobilizer", which carries additional difficulties.
4. Some are argued by the fact that this operation can cause. The weighty argument here is that the dealers argue that after the activation of the immobilizer, Lada Grant can stumble at any time. Then we can offer not to lock the doors, they may not open at any time.

Please note that in the list of pre-sale works there is an item on the basis of which the car immobilizer should be necessarily activated, regardless of which complete set.

How to find out an immobilizer activated?

If this icon is burning, then the immobilizer is not activated

If when the car starts, the "Machine Machine" icon lights up and after some time it turns, it means that the immobilizer is disabled! This is a direct threat to the safety of your car.

Instructions for activating immobilizer

1. Close all doors by pressing the "Pip" (lock lock button).
2. Include ignition with red key and wait for 9-10 seconds.
3. Pull out the key. The "key" icon should be frozen with a frequency of 5 times per second.
4. Quickly (for 5-6 seconds) turn on black ignition. 3 pits + 2 pisctions will sound.
5. Turn off the ignition and pull the key.
6. Quickly (for 5-6 seconds) while blinks "Typewriters" turn on red ignition.3 pits + 2 pisctions will sound.
7. Turn off the ignition. It will sound 1 squeak.
8. Quickly (within 5-6 seconds) include ignition for 2-3 seconds!
9. Turn off the ignition. The key in the castle. 3 pischi will sound + icon "Machines with a key" goes out. Do not take out the key.
10. Remove the key.

To check the work of the immobilizer, simply start the car, and see whether the icon "Machines with the key" is burning. If it does not burn, the immobilizer is activated!

Immobilizer activated

You can also remove the label from the key, and try to start the car. Immobilizer should not be launched a car.

At first glance, it is difficult, but in fact everything is simple. I got the first time. The process of my activation is below video.

If the engine does not start even with a label, then problems with the immobilizer itself or are possible.

Video instruction

Especially for our portal, I took a video on which the activating immobilizer on my grant. Thank you, do not thank!

Lada Kalina - one of the most sought-after cars domestic production, along with the sword prior and VAZ 2110. It is relatively economical, consumes little fuel and perfectly maneuver on busy Russian roads.

Lada Kalina - one of the most sought-after cars of domestic production: economical and perfectly maneuvering on lively Russian roads

In general, the owners arise with him not so many problems, except for the periodic enlightenment of the immobilizer who attempts to start the engine is impossible not only for hijackers, but also for the host of the car itself. This article is about the device and functions of the immobilizer for the Lada Kalina, so that it is easier to solve the problem with freezing.

In the package of all new cars VAZ, equipped with injector Engine (except for models 2101-2106) includes a regular anti-theft device APS-4 or, as an option, APS-6 (Chevrolet Niva and Machines 2004-2014 release). The principle of operation of the immobilizer of the APS-4 - transmitting data on the state of the system into the car control unit and holding the ignition circuits and fuel pump in a locked position before the host arrival so that he can unlock them with a special black key.

Video recording of the immobilizer trip to Lada Kalina

The new IPS-6 immobilizer has a more advanced design: the code key is combined with the ignition key, and the reader is placed in the steering column. A number of new features are also implemented: Diagnostics of the K-LINE device, rear PTF and power windows.

Immobilizer in Lada is a very sensitive and capricious thing. Its block can fail, even just catching interference from the owner's mobile phone, not to mention the diagnostic connection when the ignition is turned on. And all this is due to work along the K-Line line. The owners also deliver a lot of problems frequent program malfunctions.

The company VAZ even developed the function of an alternative engine launch for such freelance situations. Its essence lies in the fact that the owner can start the car only by introducing a secret password from six digits. But here, again, there are your pitfalls: the owner of the car will have to sweat, pressing the gas pedal a certain number of times to enter the specified password. In such cases, it is better to simply deactivate this core immobilizer.

So how do you still disable immobilizer by car Lada Kalina? And is it possible to do it yourself without a key?

Disable immobilizer by car Lada Kalina just - just disconnect it from the power supply

Yes, of course, you can. First of all, you need to get to it and disconnect from the power supply. To do this, you will need a knob, a cardan hinge, a cruciform screwdriver, an extension and curly bit. So, first you need to unscrew the battery and remove the protection from the dashboard.

The immobilizer is located behind heating control devices and looks like a small black box with dimensions of 5 × 10 cm. To remove it, you will have to work hard by unscrewing the bolts connecting it to the control panel. Do not forget to stop supplying the power to the APS device, pulling the plug and keeping a special plastic retainer. And be sure to reanimate the diagnostic line after removing the immobilizer.

An extraction operation is completed, you can now start setting up APS. The most important thing at this stage is to remove all the information left by the machine in the energy-dependent memory unit (ECU). This is done: it is removed from the immobilizer a regular posting connector and together contacts 9.1 and 18. After that, we proceed to the opening of the computer (if it is a Bosch M 1.5.4 model), insert a special chip with an EEPROM cleaning utility and We try to turn on the engine. As a result, the engine must start.

If it is impossible to extract the old chip, you will have to install the COMBISET program that also acts as EEPROM. Otherwise, you will need to overpass the microcircuit's socket.

For the Bosch MP7.0h ECU model, the actions will be similar due to the firmly paved storage device. Either fill the combiset or solder.

But with the device January 5.1 and the above motorists are lucky much more. They may not straighten with the EEPROM rewrite program and the same firmware read from the controller with a non-injured immobilizer. As a result, the ECU itself after reading the information will generate the code and allow you to start the engine.

Sometimes restrictions exist at stripping information. For example, from the EEPROM memory unit, you cannot delete everything completely. Then we offer you one interesting thing: you can edit the dump file by replacing its bytes from the second in the seventh letters FF.

Well, in principle, and all things. As you can see, for people who are friends with appliances, there is nothing impossible.

• news
• Workshop

In Russia, the demand for Maybahi sharply increased

Russia continues to grow sales of new luxury cars. According to the results of the study conducted by the Avtostat Agency, at the end of the seven months of 2016, the market of such cars amounted to 787 units, which is 22.6% more than in the same period last year (642 pcs.). The leader of this market is the Mercedes-Maybach S-class: on this ...

SUV GMC turned into a sports car

hennessey Performance Tumbled has always been famous for its ability to generously add additional hitch of "pumpable" cars, but this time the Americans clearly embarrassed. GMC Yukon Denali could turn into a real monster, the benefit that the 6.2-liter "eight" allows you to do this, but Hennessey motorists limited themselves to a rather modest "bonus", increasing the capacity of the engine ...

In Helsinki banned personal cars

In order to embody such an ambitious plan into reality, the Helsinki authorities intend to create the most convenient system in which the boundaries between personal and public transport Will be structures, reports autoblog. As a specialist in transport of the city hall of Helsinki Sonya Heikkil, the essence of the new initiative is quite simple: the townspeople should be ...

Named regions of Russia with the oldest cars

At the same time, the youngest fleet is listed in the Republic of Tatarstan ( average age - 9.3 years), and the oldest one in Kamchatka Territory (20.9 years). Such data in their research leads to the Avtostat Analytical Agency. As it turned out, in addition to Tatarstan, only in two Russian regions average age passenger cars less...

Dakar-2017 may pass without a KAMAZ master team

The Russian team "KAMAZ-MASTER" is currently one of the most powerful rally-raid teams of the planet: From 2013 to 2015, blue-white trucks took gold Marathon "Dakar" three times, and this year the crew under the leadership of Airat Mareev became the second. However, according to the Agency TASS, the director of NP KAMAZ-Motorsport Vladimir ...

Cars Datsun. have become more expensive at once by 30 thousand rubles

Immediately we note that the rise in price did not touch the cars collected last year. Last year's ON-DO sedan and hatchback MI-DO Basic versions are still offered for 406 and 462 thousand rubles, respectively. As for cars 2016 release, it is now on-do not buy cheaper than 436 thousand rubles, and for Mi-Do dealers from nowend asked 492 thousand ...

Ford Fiesta. New generation: already in 2018-2019

The appearance of the novelty will be performed in the style of larger Focus and Mondeo of the current generation. About this with reference to sources inside the company reports Omniauto. Based on the information received, the artist of the publication also created an image on a computer demonstrating how such a car could look like. The headlights and grille in the Mondeo style is not the only one that will ...

Video of the day: Electric car is gaining 100 km / h in 1.5 seconds

An electric car called Grimsel was able to accelerate up to 100 km / h per 1.513 seconds. The achievement was recorded on the runway of the aviation base in Dowendorf. The Grimsel car is an experimental car developed by students of the Swiss Higher Technical School of Zurich and University of Applied Sciences of Lucerne. The car is created to participate ...

Prosecutor General's Office began checking autory

According to the Prosecutor General's Office, the number of legal proceedings have sharply increased in Russia, which lead "unscrupulous auto units", which work "not to protect the rights of citizens, and to extract super-profits." According to Vedomosti, information about this department sent to law enforcement agencies, Central Bank and the Russian Union of Motorovshchikov. The Prosecutor Generalists explain that intermediaries are lack of due diligence ...

Singapore will appear unmanned taxis

During testing on Singapore roads, six modified Audi Q5 will be released, capable of moving offline. Last year, such cars freely overcame the path from San Francisco to New York, reports Bloomberg. In Singapore, drone will move along three specially prepared routes equipped with the necessary infrastructure. The length of each route will be 6.4 ...

How to choose a car for rent, choose a car for rent.

How to choose a car rental car rental - a very demanded service. In it often need people who came to another city in cases without personal car; Those who wish to make a favorable impression with the help of an expensive car, etc. And, of course, a rare wedding ...

The most expensive cars in the world

Of course, anyone at least once wondered what the most expensive car in the world. And not even receiving an answer, he could only imagine himself, which is the most expensive car in the world. Perhaps some think it is powerful, ...

Self the best cars 2018-2019 in different classes: hatchback, SUV, Sportor, Pickup, Crossover, Minivan, Sedan

Let's look at the advanced novelties of the Russian automotive market, to determine best car 2017. To do this, consider the forty-nine models that are distributed over thirteen classes. So, we offer only the best cars, so make a mistake to the buyer when choosing new car It is impossible. Best...

What machines are hijacked most often

Unfortunately, the number of stolen machines in Russia is not reduced over time, only the brands of carbonated cars are changed. It is difficult to accurately determine the list of the most hijacked cars, since each insurance Company Or statistical bureaus have their own information. The exact data of the traffic police about what ...

What car choose a family man

The family car must be safe, roomy and comfortable. In addition, family machines must be convenient to use. Varieties of family machines As a rule, most people have the concept " family car»Associate with a 6-7-miroral model. Universal. Such a model has 5 doors and 3 ...

Overview of the most popular crossovers and their comparison

Today we will consider six crossovers: Toyota RAV4, Honda CR-V, Mazda CX-5, Mitsubishi Outlander., Suzuki Grand. Vitara I. Ford Kuga.. To two very fresh new items, we decided to add more and debuts of 2015, so that the test drive crossover 2017 was more ...

How to choose a used car, what a used car to choose.

How to choose a used auto who want to buy a car quite a lot, but not everyone has the opportunity to purchase a new car in the cabin, which is why it is worth paying your attention to used cars. Their choice is not easy, and sometimes it's from all the variety ...

How to exchange your car to a new one, how to exchange the car.

Tip 1: How to exchange your car for a new dream of many motorists - come to the salon on the old car, and go to the new! Dreams become a jaw. More turns are gaining an old car exchange service for New - Trade in. You do not...

What you need to know to take a car on credit?, How long to take a car on credit.

What you need to know to take a car on credit? Buying a car, and especially at the expense of credit funds, is far from the cheapest pleasure. In addition to the principal amount of the loan, reaching a few hundred thousand rubles, it is necessary to pay interest banks, and considerable. In the list ...

• Discussion
• In contact with