Washing machine for washing parts. Washing machines. S300 Washing, blowing and drying empty plastic boxes

the main / Advice

Today, in the machine-building and metalworking industries, where technology requires the washing of parts and assemblies, more and more new and sophisticated washing machines are used, which can increase quality and productivity, reduce energy costs and have a negative impact on the environment.

One of the striking examples of manufacturers of such washing equipment is the Italian company TEKNOX. For over 40 years, this company has been producing a wide range of jet washers for washing parts and assemblies - from small-sized washers to complex conveyor systems of the continuous type of multi-stage processing. The uniqueness of TEKNOX washing machines is that the parts are washed in a closed continuous cycle. The washing process is carried out with a hot water pressure washing solution. The solution, in the tank of the washing machine, is heated (up to 80 ° C) by electric heating elements and a hydrodynamic pump, through the filtration system, supplied under pressure (up to 10 bar) through a multitude of nozzles to moving parts in the form of jets, after which, with washed off impurities, it flows back tank. On contaminated parts in washing machines there are three types of impact: mechanical and physicochemical. Mechanical impact means the impact of many jets of high pressure solution, and physicochemical impact means their temperature and reactivity.
Jet-type machines allow not only washing and degreasing parts from contamination with a washing solution, but also imparting certain properties (adhesion, anticorrosion) to their surfaces using appropriate special solutions. To this end, leading manufacturers of the chemical industry offer a wide range of effective and safe concentrates for various materials and contaminants. All washing machines are designed in such a way that parts and units are washed in automatic mode. The operator only needs to set the program settings and start the machine. In the machine control unit, such parameters as the duration of washing, blowing, removing vapors, drying, the temperature of the solution heating, as well as automatic daily heating of the solution before the start of the work shift are programmed. Washing machines are made of non-magnetic stainless steel AISI 304 and are designed with a safety margin for guaranteed operation in difficult conditions... All machines comply with EU safety regulations.

Advantages of jet washers

triple impact;

high performance;

low concentration and temperature of the solution;

profitability;

safety and environmental friendliness.

Applications

The fields of application of washing machines are very diverse. This can be washing and degreasing, finishing parts, assemblies, units before assembly or painting, processing after casting or machining. The machines are also used for degreasing, anti-corrosion treatment, pickling, phosphating, paint removal, etc. The manufacturer divides the use of washing machines into two categories: in the maintenance and repair of machinery and equipment (washing parts that have been removed from machines, tools, motors and mechanisms, etc.) and in production (washing new parts after mechanical: turning, drilling, milling, grinding, etc.).

Maintenance and repair of machinery and equipment

Parts removed from machines for repair are mostly covered with various dirt: sand, oil and grease, rubber from gaskets, sealant residues and various putties. Cleaning of parts with such contamination is best carried out in washers, if possible, with a high-pressure pump and heating the solution above 60 ° C, but without additional filter systems, since such a large amount of dirt can easily clog any fine filtration system.
Previously, petroleum-based solvents and derivatives were used for this, which dissolved fats, and then the residual contamination was washed off the part with a washing gun. Mostly submersible equipment was used, where parts were immersed in a reservoir with a solvent, then they were rinsed with water and wiped by hand. After several washes, the liquid in the reservoir became dirty, and residues of oil and dirt settled on the washed parts. And since toxic solvents were used and there were no adequate exhaust systems, the workrooms were saturated with harmful vapors. In order to imagine the damage this caused to the health of personnel, we will provide some information on the toxicity of solvents.
Chlorine solvents are carcinogenic, and in the presence of an open fire (lighted cigarettes, burners), they decompose and turn into a nerve-paralytic, lethal gas. Aromatic solvents - oil derivatives - are flammable, carcinogenic, toxic to the respiratory tract. Other solvents also cause irreparable harm to health. In Europe, the use of solvents is currently prohibited. They are used only in closed circuit degreasing equipment. In the coming years, bans will be introduced on the production of any type of chloride solvents, as well as other solvents that affect the formation of the ozone hole and are dangerous when indoors. In some areas, such as space, military, etc., hazardous solvents are still used, guided by the approved many years ago regulatory documents... In the meantime, washing with solvents can not only be replaced by washing with water-based solutions, but can also be optimized using jet equipment with two or three stages of washing and rinsing and a filtration system.
Modern washing systems with a rotating basket (platform) and an effective alkaline detergent, non-toxic and not harmful to the environment, allow you to achieve excellent results washing parts that are processed as part of a maintenance or repair operation.

Temperature of 3% alkaline washing solution 70 о С, washing duration 15 minutes
Washing machine 1200HT

Features of the choice of the type of washing machine in the field of maintenance and repair of machinery and equipment

The model of the washer should be selected taking into account the maximum dimensions of the parts to be washed. As practice shows, the most popular are following models washing machines:

UNIX 60-80- for flushing small parts during repairs and Maintenance automotive technology (this installation is not suitable for washing engines and gearboxes in general);
UNIX 100-120- for washing parts of cars and small vans (car engines with no more than 6 cylinders);
ROBUR 1400- for washing any parts of engines and gearboxes of utility vehicles;
ROBUR 1800- used for washing the largest engines, engines of military vehicles, machines for the mining industry, etc.

Models of washing machines with two baths are usually used for more thorough rinsing, the results of which are more stringent. For example, for washing parts of aircraft, helicopters, when grinding engines, when rinsing not only achieves a more aesthetic appearance processed parts, but also removes from their surface those contaminants that could have formed after previous rinsing operations.

Manufacture of machinery and equipment

In the industrial production of machinery and equipment, great attention is paid to the cleanliness of new parts before assembly or packaging. Since the quality of product operation largely depends on the washing results, very different requirements are imposed on washing machines than in the field of maintenance and repair. Here you have to deal with the most difficult problems to solve and with a huge variety of types of machines. In addition, in the industrial sector, such an extremely important requirement as quality is put forward.

The fact is that in this sector now it is required not only to degrease parts, but also to wash off various solid particles remaining after machining (chips, abrasive materials, etc.) from them. Moreover, these particles have to be removed both from the outer walls and from blind holes, threaded holes, from all kinds of passages, water and oil distribution channels, the presence of which is distinguished by many mechanical parts. It is enough, for example, to look at engines and other automotive components where there are many blind holes and piping for water cooling or lubrication systems. Based on these few examples already, it is easy to understand that now immersion washing is not enough, even if it is used in combination with ultrasonic treatment or basket movement, since solid residues from the treatment will still be present in a suspended state in the washing bath, which will inevitably settle again on a part that has already been washed.

Achievement of the required quality of washing is possible with washers with a rotating basket. The immersion principle is excluded here, and the chips do not settle on the washed parts. In addition, this equipment is equipped with a bag filter, which is used when small metal particles cannot be captured by a conventional mesh filter.
Simple parts (sheet or stamped) do not pose any problem for successful rinsing, since here it is only a matter of degreasing the surface. The only thing is to arrange the parts in such a way as to avoid the "glass effect", that is, they should be installed so that the liquid after rinsing does not stagnate inside the part, but flows freely. In addition, to avoid areas of darkening, the parts must not block each other from the water jets. The selection of a washer for complex parts such as cast iron and aluminum alloys, parts with holes and machined parts must be more careful.

Features of the choice of the type of washing machine in the production of machinery and equipment

For many simple parts of a simple shape with a small number of through holes, as well as for small batches of various parts, standard washers with a rotating basket (platform) are used.
For more complex parts, in some cases, you can use modified models of washing machines that are adapted to perform washing in options involving positioning or calibration.

Special configuration washing circuits

And only in those cases when especially high and stringent requirements are imposed on the quality of washing of parts and assemblies, It is NECESSARY to use the above named special washers that provide calibration and positioning. In this case, machines must be specially designed taking into account both the type of parts (their features, structure and configuration) and the type of technological cycle (the number of phases, baths, pressure, filtration method, etc.). For such specific cases, in the serial production of identical or similar parts, you can focus on equipment of the type:

ROBOJET - for washing large parts and parts with a large number of blind holes (gearboxes, differentials, gear cases, components of hydraulic systems, etc.).

ROBOCLEAN – small-sized washer for a small area for washing critical parts of small dimensions.

Washing machine for parts and assemblies, units, washing complex units.

ROUNDJET - for washing small parts (installation with a single loading and unloading area).

TUNNEL – for cleaning small and medium-sized parts, parts manufactured in series, with a large number of blind holes and threaded holes (components car engines made of aluminum, pump parts, etc.).

ROTOR - for washing delicate small and small parts made of aluminum, brass, bronze, steel with external thread or threaded holes.

LINEARJET - for washing long products (axles, cardan and crankshafts, bed, etc.) of various weight characteristics.

There are models of washing machines with two or more baths (tanks). The need for these machines arises in the following cases:
- cleaning of parts made of aluminum or alloys of copper, brass, bronze, etc. is required, and it is necessary that the parts come out shiny, without stains. In this case, after washing, rinsing with demineralized water is necessary;
- when parts are made of cast iron or steel and it is required to provide protection against corrosion for at least 30-60 days. For this, a suitable agent is added to the second rinse tank to prevent or retard oxidation (corrosion). Protective equipment are different types: on the oil based providing protection for 30-60 days, and dry protective equipment providing protection for a maximum of 30 days.

Recently, detergents have appeared on the market that simultaneously degrease the surface of parts and provide protection against corrosion, that is, the washing cycle is shortened and is reduced to processing in only one bath. This makes it possible to simplify the design of the washing system and reduce the cost of machining parts.

There are models of washing machines that provide the phosphating process. Technological processes of phosphating can be carried out in different ways, but in our installations only jet methods of processing parts are used, not submersible ones. Metal surfaces are phosphated before painting to ensure good and longer adhesion of the paint to the surface. The washing machines under consideration use the principle of spraying acid-based phosphating substances mixed with water. The practice of their use turns out to be much more economical in comparison with the use of solvents, moreover, they are much less hazardous, and at the same time, they are able to provide quite equivalent results. The only problem that has to be reckoned with in this case is that there should be more than one, two or three (and even more) baths, and the chemical composition of each of them must be monitored almost daily.
The result is a better grip. paints and varnishes... One more advantage of the proposed technological processes should be noted: it is possible to reduce toxicological problems in the working room to zero.

You can talk endlessly about the advantages of TEKNOX washing machines. But, perhaps, the best confirmation of their quality is the names of consumers - for several decades, the company's products have been supplied to world-famous engineering enterprises such as BREMBO, LAMBORDINI, Same Deutz Fahr Group Italia Spa, Same Deutz Fahr Group Italia Spa, Bonfiglioli Riduttori Spa , Ilva Spa, Oto Melara Spa, Rietschle Thomas Italia Spa

OUR EQUIPMENT IS PROFESSIONAL AND DEEP CLEANING OF ANY METAL PARTS AND SURFACES

Metalworking

Industry

Electronics

Medicine

How we are working?

When selecting washing machines for washing parts, our specialists conduct a deep analysis of the set production task, the specifics of each specific production and the parts to be cleaned. As a rule, the same task of flushing parts can be technically solved using several fundamentally different technological approaches based on different washing installations... There are a number of significant differences in these technologies, which determine the possibility / impossibility or desirability / undesirability of their application in specific enterprises. By contacting us, you get not only a qualified selection of technological solutions, but also the opportunity to choose the most optimal washing technology, taking into account all economic and production factors.

What do we supply?

The range of washing equipment supplied by NTK Soltek includes domestic and foreign developments in the field of the following cleaning technologies:

purification systems in aqueous solutions;
ultrasonic cleaning systems;
hydrokinetic washers for cleaning parts;
industrial washing machines for cleaning in various solvents (perchlorethylene, trichlorethylene, modified alcohols, hydrocarbon cleaners ...);
cleaning installations printed circuit boards and stencils ...

And much more for your specifics!

More about us

A professional approach to the selection of equipment, detergents, organization of the cleaning process of parts is the main profile of our company. By contacting NTK Soltek with the task of buying a washing machine, you are guaranteed to receive a selection optimal equipment for specific production tasks. In a number of cases, when choosing the final solution, the necessary experiments will be performed to confirm the applicability of the proposed purification technology. In our daily work, we closely interact with domestic and foreign manufacturers of washing installations, participate in various industry events, take part and conduct various conferences and seminars on the topic of surface cleaning. The specific equipment and configuration of the equipment is selected on the basis of a detailed analysis of the task of cleaning parts. At the same time, the final decision can be based both on the use of high-quality equipment of European production, and on the choice of Russian washing machines, the price of which is significantly lower. Industrial cleaning in general and precision cleaning of parts in particular are areas in which we have accumulated deepest practical experience. This experience, knowledge and understanding of the essence of cleaning processes underlie the choice of our Customers NTK Soltek - as a supplier modern technologies industrial cleaning in general, and washing machines in particular.

Description of equipment

The washing machine is designed for jet cleaning and degreasing of parts. The working chamber is made of stainless steel, has a hermetically closed door- hatch for loading parts. Inside the chamber there is a roll-out, lattice platform (onto which the parts are loaded), ramps from the bottom and from the top. The upper ramp has a G- figurative view and moves along the portal due to the electric drive, the lower ramps are electrically driven and swing. This type of ramps allows you to wash parts from all sides. ( c top, bottom, sides).

The parts are washed with streams of washing solution from the nozzles in the chamber. The nozzles are directed so that the jets of the cleaning solution affect all areas of the surface of the parts; if necessary, additional nozzles are installed to target specific areas of the surface. The detergent solution from the collection chamber of the washing chamber enters the filter basket of the storage tank, and then into the tank itself.

The outer surfaces of the working chamber and storage tanks are covered with thermal and noise insulating material, decorative panels.

Cleaning solution tank:

The washing machine of the unit is equipped with a storage tank for storing the cleaning solution. The bottom of the tank is made with a slope for the convenience of periodic maintenance. The tank is equipped with a heating system for cleaning solutions and liquid level control, as well as pipes for draining and replenishing solutions. Stainless steel heating elements are used as heating elements.

Machine control system:

The system is built on the basis of an industrial controller, which allows programming special modes processing for individual parts or types of parts. Includes protection of pumps against dry start, protection against surges and power failures in the enterprise network. Operator to be able to set working temperature solutions, as well as the running time of each stage.

Loading platform:

The loading platform is made of stainless steel and equipped with rollers. On the surface of the platform, there are limiters that indicate the boundaries of the working space of the washing machine.

The basic equipment of the washing machine includes:

Body, tank made of stainless steel AISI304.
Heating elements made of stainless steel.
Loading platform, ramps, stainless steel piping.
European electrician Schneider.
System for automatic maintenance of the solution temperature with a maximum heating limit of 90 ° C.
Programmable weekly timer.
Forced extraction of steam.
Tank solution level sensors.
Dry run protection.
Coarse filters on the drain from the working chamber.
POD for loading a platform with guides.
Pneumatic lifting of the hatch with compressed air (Sealed door).
Electric drive of the upper wash manifold.
Reactive drive of the lower wash manifold.
Thermal insulation of the case
Program control
Contaminated solution regeneration system by settling in a sump and
Overflow oil separation system.
Bag filter with self-contained pump.
Steam condensation system.
System pressure gauges.

Information on correct selection washing machine to clean your parts. Cleaning of parts has always been a problem in the mechanical engineering industry, as you always have to choose the washing technology depending on the material and type of parts, for example, made of aluminum, copper, steel, cast iron, etc. In this regard, it is important not only to choose the type of machine, but also to conduct research on the selection of the chemical composition of the washing solution. In this brochure we will show several examples of the application of washing machines, but in practice there are many more tasks for cleaning parts.

I am ready to help all my clients to choose the right washing machine for their specific tasks. In any case, our technical staff will be very happy to advise you and answer all your technical questions. Please do not hesitate and contact us at any time.

Top loading washers

Purpose: for cleaning motorcycle engine parts, passenger cars and medium-tonnage commercial trucks and minibuses. Materials of the parts to be cleaned: aluminum, cast iron, steel and other non-ferrous alloys. Parts are washed inside the chamber with spraying of a washing solution under a pressure of ~ 3 atm. through a large number of nozzles.

A special container is used for washing small parts

Model L-321 for cleaning heads and cylinder blocks

Front-loading washing machines

Purpose: for cleaning parts of LARGE SIZES of engines of passenger cars, medium and large-tonnage commercial trucks, tractors, buses and special equipment. Materials of parts to be cleaned: aluminum, cast iron, steel and other non-ferrous alloys.

The parts are washed inside the chamber with the spraying of a washing solution under pressure in an automatic computer-controlled mode. The washing solution circulates inside the machine and is disposed of (at the end of its washing properties) by a special pump.

Basket dimensions

X53 Series Single Tank Washer

Washer with two tanks (with rinsing function) -X53 / 2 series

Generator Washing Machine

L-212 mold washing machine

Tunnel (conveyor) type washing machines

The choice of the type of washing machine between top / front loading of parts, as well as a tunnel (conveyor type) machine, as a rule, depends on the geometric parameters of the parts and the required cleaning performance.

All models of washing machines are shown in our catalogs.

: the basic equipment of the machine with a belt conveyor for cleaning parts has the following functions: -washing; - drying; - conveyor belt speed (smoothly adjustable) - 0.2 ... 1 m / min.

: A very flexible machine with a belt conveyor for cleaning parts, which is available in two basic configurations with the following functions:

Option 1 (single tank)- sink; -drying.

Option 2 (two tanks)-washing; -rinsing;

Drying. - conveyor belt speed (smoothly adjustable) - 0.3 ... 1.5 m / min.

All washing machines can be modified, for example, with additional options to meet the needs of customers. It is important to keep in mind that the low speed of the conveyor belt is used for washing complex shaped parts, and the high speed is used for simple shaped parts.

Standard G400 / 2

Silver S300 Washing and drying of all types of pipelines

G1000 / 2 Washing, rinsing, blowing and drying of steel wheels for cars

G400 / 2 Chain conveyor for washing, rinsing, blowing and drying of car gimbals

S300 Washing, blowing and drying empty plastic boxes

S300 Washing, blowing with compressed air and drying of heavy parts

G400 / 2 Chain conveyor for washing, rinsing and blowing off pipeline parts

Silver S300 Washing and rinsing car parts

Silver S400 Option for washing and rinsing car parts in plastic boxes

S300 Washing and drying car parts

Several variants of parts for washing in conveyor washers

Spiral drum machines

The machine has a spiral-drum section, in which the parts, rotating in the drum, are first cleaned by immersion in a washing solution, and then washed.

These machines are designed for washing both small and large batches of small parts such as bolts, nuts, washers, etc.

Two series of such machines are produced: JOLLY LINE “J” - simple car for washing small batches of parts. This machine has functions: washing and drying only. As standard, this machine has limited quantity modifications. SPIRA LINE “SP” Fast-adaptable spiral drum machine with the functions of washing, rinsing, blowing and drying, intended for medium-large-scale production. This series has a sufficient number of modifications that can satisfy the needs of any Customer. IN basic configuration available in two versions: Single tank - washing and drying; Two tanks - washing, rinsing, drying.

Spira 480/2 Washing + double rinsing + blowing + drying of rivets for aviation

N2 SP480 / 2

Washing, rinsing and drying stainless steel sawdust

……..AND MUCH MORE

Platinum Series

Rotary machines with a horizontally rotating drum make it possible to work out the technology of washing parts of very complex geometric shapes. Washing principle: the parts are sprayed and at the same time the washing solution is immersed while the drum rotates in the horizontal plane.

The washing machine PM 400 has two drums and provides the following functions: spraying of detergent solution + immersion and rinsing + drying of parts. This machine is available with various options.

Washing machine 600-1200-1500 has one drum and performs: spraying of detergent solution + immersion and rinsing + drying of parts. This machine is available with various options.

Washing machine Р600 / 2-1200 / 2-1500 / 2 - has one drum and performs: spraying of detergent solution + immersion and rinsing + rinsing + drying of parts. This machine is available with various options.

PM-400 washing + drying of parts

PM-400 washing + drying of car parts

P1500 / 2 M washing (inside-outside)) + rinsing, blowing + drying of large blocks

P600 / 2 washing + rinsing, blowing + drying

Copper parts

A few examples of parts for washing in platinum series machines

……….. and much more

We will illustrate the choice of the type of machine depending on the dimensions of the parts by the example of parts with geometric parameters of 40 × 40 × 20 mm, which have a volume of 32000 mm³ or 0.032 liters. If you need to wash such parts in the amount of 600 pcs. per hour, then the volume of your parts will be 0.032 × 600 = 19 liters. According to the Magido catalog, the Jolly J-320, which has a capacity of 30 l / h, will be the most suitable for this task.

HOW TO CHOOSE THE RIGHT WASHING MACHINE DEPENDING ON THE VOLUME OF ITS ONE LOADING

Option 1 Basket filled with small parts

Sink parts Diameter 40 mm Inner hole 25 mm

For example, the volume of the basket is 7 × 9 × 8 = 504 liters. Let's say that with an eight hour shift over 5 days, you need to make 25 downloads. Then in a week you need to load 25 baskets × 504 l = 12 600 l (part volume) into the machine.

A week includes 40 working hours, so in one hour you need a washing machine capacity 12600/40 = 315.0 l / h.

According to the Magido catalog, we select the washing machine that is closest to the required characteristics - SP-640, which has a capacity of 360 l / h. Features of this machine: - when washing parts only from oil contamination (without shavings) - the cycle is realized: washing + drying (SP 640); -when parts are washed from oil contamination and metal shavings, the cycle is carried out: washing + rinsing + drying (SP 640/2).

The washer has a helix pitch of 200 mm.

ATTENTION. IT IS NOT POSSIBLE TO WASH 300 MM LONG PARTS IN THE SP 640 WASHER. If it is necessary to wash parts longer than 300 mm, the Platinum series must be used. For example, the Jolly series machines wash parts less than 300 mm, and the Platinum series machines can wash parts over 300 mm.

Option 2
Washing rectangular parts

The volume of one piece is 40 x 40 x 150 = 240.000 mm³

With an annual program of washing such parts in the amount of 10,000,000 per year, it is necessary to wash 10,000,000: 250 (working days per year): 8 (hours per day) = 5,000 pcs. In this case, the estimated required productivity of the washing machine must be at least 240,000 mm³ x 5000 pcs / hour: 1.000.000 = 1200 liters / hour.

According to the Magido catalog, we select the P-1500/2 washing machine that is the closest in terms of the required characteristics, which has a washing capacity of 1800 l / h.

Option 3
Cleaning of fasteners

To accomplish this task, the most popular solution is to use two models of washing machines: model Spira 640 - 240 l / h with a continuous supply of parts, model Platinum 1200/2 - 240 l / h loading of parts into a basket.

Probably every Russian motorist has seen at least once in his life how a carburetor is washed in kerosene; and, perhaps, he himself has repeatedly done this. But fortunately times are changing, and technologies are changing ...

Today, there are practically no carburetor cars left; and most people prefer to repair them not in the garage "at Uncle Vasya's or Ashot's", but in a modern car service, equipped with the latest technology. After all, the more modern and more expensive car, the higher the requirements for its repair, including the elements and assemblies used.

When repairing a car engine, a lot of time and effort is spent on cleaning it from oil residues and other operational contaminants. Unfortunately, this does not take into account the harm caused to health at all; when the mechanic inhales harmful vapors of cleaning solutions and liquids.

The most optimal way out of this situation is automatic installation for washing parts of a closed cycle MAGIDO (made in Italy).

Washing in a car workshop can significantly speed up the process of washing components; facilitates the work of the mechanic, freeing his hands from the routine and painstaking process; and in general, makes the work of car service employees cleaner and more environmentally friendly.

In addition, any such MAGIDO parts washer is made of high quality stainless steel. This allows you to avoid corrosion and operate it for a long time without any problems.

The principle of a parts washer is very similar to that of a dishwasher. The main difference is that the basket in which the components are placed rotates and the cleaning solution can be reused.

How the MAGIDO parts washer works

1. First you need to place dirty parts or assemblies in the washing chamber. Although additional supports are installed in MAGIDO devices to prevent distortions, it is still advisable to distribute them evenly throughout the basket.

3. Inside this device there is a U-shaped frame in which stainless steel nozzles are built. This is to prevent the build up of scale from clogging the nozzles. The cleaning solution is fed through them at a pressure of 2.3 to 4.7 bar.

The pressure depends on the model of the device; in addition, it can be increased by individual order. In a number of models, to increase productivity, two pumps are used (for example, in the MAGIDO stands L102 and L122).

The position of the nozzles is adjusted so that the washing solution, falling under pressure on parts or assemblies, rotates the basket of the device.

4. Some parts washers are equipped with a built-in geared motor that rotates the basket at a specific frequency. As a rule, these are models designed for a maximum load - from 350 kg.

In principle, a geared motor can be installed on any cleaning device and aggregates (except for the ECO series); but this option is installed directly at the factory in Italy.

5. At the end of the cycle, the timer is turned off and the device can be opened. In this case, you must be careful, because the detergent solution heats up to a temperature of 70 C, and there is a danger of scalding from the steam. To avoid this, the MAGIDO parts washer has one additional option- extraction of hot vapors.

At the end of the cleaning process, it is recommended to leave the clean components in the device for a few minutes at open lid... This will allow them to dry almost completely. in the process, the devices get very hot and, as a result, dry quickly when cooled. However, moisture may remain in the recesses of the elements.

The process of flushing the elements occurs in a closed cycle: the liquid from the nozzles first cleans, then flows into the tank; then through a filter that retains large particles, it is again fed into the nozzles. Those. there is no need to change the cleaning solution after each cleaning cycle.

Washer for parts and MAGIDO units and all of its models are equipped with a function to control the level of the detergent solution. This avoids damage to the heating elements.

It must be remembered that it is not recommended to place parts in the system basket that are smaller than the basket cell itself. For washing small items, the kit includes a basket with a fine mesh (for all except the ECO series).

The average delivery time for this unit (if they are not in stock) is 45-60 business days. Parts washing equipment is available on request only. The delivery time for such devices is about 90 working days.

How often should the cleaning solution be changed?

This is a subjective parameter. As soon as it becomes clear that the elements are poorly washed, and an oil film remains on them; the cleaning solution must be changed. It all depends on how much dirty parts are washed in the parts washer. For example, you can wash slightly contaminated items, or you can clean parts that were on military preservation.

What liquid should I use to flush parts?

It is strictly forbidden to use any flammable materials and foaming solutions. A small amount of detergent concentrate is supplied with the device, which is enough for the first filling. We recommend further use of Russian counterparts, for example, "Labomid".

How to choose the right cell washer?

1. First you need to determine maximum dimensions units intended for flushing. They must not exceed the diameter of the basket and maximum height boot device.

2. In addition, you should know the maximum total weight of the basket load. Excessive loading weight can lead to damage to the entire device.

Some large industrial models can be fitted with gas or diesel heating.

What options are used on MAGIDO?

To begin with, it is worth noting that all options are installed only at the manufacturing factory in Italy. Therefore, it is absolutely necessary at the stage of ordering to decide on a list of all the necessary additional options.

Oil separator. The principle of its operation is as follows: a thin metal disc slowly rotates over the surface of the cleaning solution and an oil film adheres to it. The disc then passes through two blades, which remove the oil film from it.

Basket electric drive. Rotates the basket at a specific frequency. In some units it is included in standard equipment... Recommended for flushing heavy components.

External insulation of the body of the device. Protects the mechanic from accidental burns when in contact with the body of the device and reduces heat transfer during the heating of the cleaning solution. Since 2013, MAGIDO has started production of models: L160, L190 and L210 with already installed housing insulation.

Vapor extraction device. A fan built into the back of the device allows vapors to escape from the device outside.

Minimum water level control and automatic water filling. This option requires a permanent connection to the water supply.

Stainless steel nozzle frame and basket. Serves to extend the life of the device.

Hour counter. Allows you to calculate the working time.

Weekly programming. Allows you to turn on the heating of the cleaning solution before the start of the working day and thereby save working time.

Hot drying. Forced drying of clean elements. Electric heating 3kW.

Carriage for moving the basket. Trolley for removing / installing the basket into the device. Not used for all models. Standard on units: L160, L190 and L210.

Increase in maximum load up to 1500kg. For models only: L160, L190 and L210.

Alternative use of sinks for MAGIDO parts and assemblies

Washer for washing parts can come in handy not only in car services. This device is actively used in railway depots in Germany and France. In Russia, the demand for MAGIDO products is also growing every year. These devices are used in metallurgy, jewelry and medicine. Large devices are also used in the repair of quarry equipment.

Firm MAGIDO MANUFACTURES ANY INDUSTRIAL DEVICES for special orders. This can be a conveyor belt for washing small bolts or a line several tens of meters long for washing non-standard components. All that is needed for a special order is to provide a technical assignment for the factory so that Italian engineers can complete the project and calculate the cost and production time.