Cargo Ford Transit. NEW with pneumatic suspension

Official Dealer for the sale of new cars Ford Transit Aaron Auto offers for sale ready car already with installed pneumatic suspension on bounce cargo Ford Transit..

These cars Ford with pneumatic suspension can buy Already available in Moscow on Ryabinovaya Street. On the this car Was installed rear set of auxiliary pneumatic suspension from two-circuit control system. This system The air preparation is equipped with an air receiver for a faster and simple lift of the body even with maximum loading.

Even if your car does not have a regular pneumatic suspension, this is not a problem. Our specialists in Aaron cars can install the air suspension on your spring car in a short time. All major pneumatic kits for commercial vehicles are always available in stock in Moscow.

New Ford Transit It easily sends with the slightest load. Each transport company Trying to use your fleet of commercial trials to Maxim. But passport capacity Ford Transit. does not always coincide with the wisp of the customer weight Limit With comfort. The most correct and flexible way to compensate for the sedimentation of the new Ford of the transit is to install an additional pneumatic suspension to the standard springs.

This installation method pneumatic suspension Allows you to save regular suspension elements unchanged. When installing the axial set of pneumobalons, welding, drilling or finalization of the standard suspension is required.

Pressure in pneumatic powders is regulated by two control keys and is controlled by a double-rail pressure gauge with a suspension:

In this case, there is no need to get a regular wheeled compressor to change the pressure. You can adjust the car height from the cab.

Pneumatic control system is installed under passenger seat and hidden from prying eyes:

An additional receiver output can be used to swing the wheels or display the pneumatic signal - the most loud reminder of yourself in the overall stream.

Many choose it as an alternative to Sprinter. At the cost of "transit" less, and the characteristics of carrying capacity and comfort are at the same level. Exist different modifications Data trucks - from minibuses up to 20 cubic vans and refrigerators. Usually, springs or springs are put on the rear axle "transit". But many owners make a replacement for this that it gives? Consider in our today's article.

Characteristic

Pneumatic is a type of suspension, with which adjustment is possible road Suit. Such a system is widely used on commercial transport. Manufacturers gradually leave the archaic multi-ride springs in favor of Pneummobalon.

Now they are equipped with all semi-trailers and heavy trucks. As for small commercial vehicles (up to three tons and below), the pneumatic suspension is less common here. The urgency of the car - the system is much more difficult than screw springs and springs. How the pneumatic suspension is arranged, let's tell below.

About design

This system consists of several elements:

• Air cylinders. They act on the principle of springs and springs - hold the weight of the car and partially quench the oscillations. What pneumatic cylinders look like on "transit", you can see below. They are made of a thick piece of rubber. Inside filled air under high pressure. Due to its elastic design, the pillow can change the form, thereby adjusting the clearance.

• Compressor. Used to download air to the receiver. The latter has a volume of from 3 to 10 liters. When "Ford Transit", it is recommended to use a 10-liter receiver. Usually it is located in the bodies or in the cabin. Note that the budget pneumatic suspension, the "Ford Transit" is installed, may not include these items (receivers). As for the compressor, it is the main component of the system. Without it, the work of the suspension is simply impossible. The unit is operating from the 12 volt network and automatically turns off when a certain pressure is reached.
• Air highways. On them the air moves under pressure from the compressor to the actuators.
• Electronic sensors. Track the position and tilt of the car body in real time. Thus, cylinders can roll up at a certain point, making cars more stable on the road. These sensors interact with the control unit. But such electronics is rarely installed on commercial transport. More often than business and premium cars.

What is the relevant revenue?

Choosing a package of pneumatic suspension on Ford Transit, do not save on this item. The device allows you to store air under pressure for a long time. If necessary, raise the car, the air from the receiver is quickly (within 4-5 seconds) replenishes the pneumatic block chamber. The latter becomes more solid, and clearance - increases. In the absence of the receiver, the air injection will be carried out directly in the pillow. But it is very long and harmful to the compressor. With frequent use, he can simply burn.

Benefits

How does Ford Transit behave on the pneumatic suspension? Owners claim that the installation of pillows allows to eliminate the effects of car overload. These are lateral rolls, versator breakdown and suspension breakdowns. As for the last factor, the balloon acts as a buffer, preventing the frame from contacting the frame with an indigenous springs.

What else do they say about the "Ford Transit" on the pneumatic suspension reviews? Also, the car becomes more comfortable. The pillow smoothly extinguishes the oscillations and blows at the road at irregularities. For this reason, the installation of pneumatic suspension is often produced on Ford Transit Minibus.

Nevertheless, the main factor that pushes the owners to install the air suspension in Ford Transit, is an increase in load capacity. And with this task, cylinders, according to reviews, cope "on excellent." The load on regular springs is minimal, and the clearance remains the same.

disadvantages

Why is the pneumatic suspension on the cargo-passenger "Ford Transit" and other modifications not put from the factory? One of the negative factors is low maintainability. In the event of a breakdown of a cylinder (and this is depressurization), it must be changed entirely. The compressor is also difficult to repair. Yes, and the system itself is not cheap. How much will the installation of a pneumatic suspension on "Ford Transit" cost? Price itself budget option It starts from 20 thousand rubles. Full set Can be installed for 100 thousand.

What to choose?

For small commercial vehicles, the air suspension is often chosen on the rear axle.

As for the type, it is better to establish a system with one contour. You can put a two-kinnoye, but it makes no sense - they say reviews.

Installation

How is the installation of a pneumatic suspension on the "Ford Transit" with your own hands? Note that it does not need to fully remake the chassis for installation. Consider the most popular option - the installation of a single-mounted pneumatic suspension on the Ford Transit (the price of the kit is from 15 thousand rubles) on the rear axle. At first, the brackets under the pillows are installed. The top is attached to the frame, the bottom - to the spersion sheet.

During the work, it is necessary to do holes for bolted bolt connections. Next here are pneumatic cylinders. The hoses are connected to them. The compressor with the receiver is better installed in the cabin. In the open space, the place is limited, and in the body (if it is a booth) it may be damaged. Connect electromagnetic valves to the unit and display the control panel to the front panel. On this, the installation of the pneumatic suspension in Ford Transit is completed. Tubes should be laid by inner side Rama, attacking them on the clamps.

We extend the resource

In order, the cylinders served for a long time (and this is half the value of the entire system set), you need to know some rules for the care of them. Rubber coating of pillows is very afraid of road reagents and dirt. Even small particles are capable of acting as abrasive at the joints of the parts of the pneummobalon. So that the pillows serve for a long time and did not descend, it should be cleaned from dirt periodically. A B. winter time - process silicone.

With a decrease in temperature, rubber becomes solid and even in the absence of dirt begins to "eat" itself. Silicone will create a kind of layer, which will provide the free course of the pneumatic makeup.

Conclusion

So, we found out what a pneumatic suspension is, as for which it is installed on "Ford Transit". Judging by the reviews, many remain satisfied with this choice. Pneumatic suspension improves car stability on the road and increases load capacity, which is particularly relevant in commercial activities.

The official dealer for the sale of new Ford Transit cars "" offers for sale the finished car already with a pneumatic suspension on a duplex cargo Ford Transit.

Data Cars Ford with pneumatic suspension You can buy already available in Moscow on Ryabinovaya Street. On this car was set with. This air preparation system is equipped with an air receiver for faster and simple lifting of the body even with maximum loading.

Even if your car does not have a regular pneumatic suspension, this is not a problem. Our specialists in can establish a pneumatic suspension to your spring car in a short time. All major pneumatic kits for commercial vehicles are always available in stock in Moscow.

New Ford Transit easily sends with the slightest load. Each transport company tries to use his commercial tarnport park at Maxim. But the Passport capacity of the Ford Transit does not always coincide with the wishes of the customer to take the maximum weight with comfort. The most correct and flexible way to compensate for the sedimentation of the new Ford of the transit is to install an additional pneumatic suspension to the standard springs.

This method of installing a pneumatic suspension allows you to save regular suspension elements unchanged. When installing the axial set of pneumobalons, welding, drilling or finalization of the standard suspension is required.

Pressure in pneumatic powders is regulated by two control keys and is controlled by a double-rail pressure gauge with a suspension:

In this case, there is no need to get a regular wheeled compressor to change the pressure. You can adjust the car height from the cab.

The control system of pneumatic elements is installed under the passenger seat and hidden from prying eyes:

An additional receiver output can be used to swing the wheels or display the pneumatic signal - the most loud reminder of yourself in the overall stream.

Left Pneumatic Falcon Ford Transit:

Right Pneumonobalon Ford Transit:

Increase the lifting capacity and endurance of your Ford Transit, setting the auxiliary air suspension to the standard system of spring. This will not change the location of standard parts, however, will provide your car in many advantages:

• Increased lifting capacity without damage to the car;
• Reducing detergent;
• Reduction of car rolls;
• Fast boost of a set of pneumatic suspension.

What do pneumatic powders, installed in the Ford springs?

Exclude suspension breakdown, car roll, comfort and energy consumption increases, the suspension becomes collected, quiet. With pneumatic bullons in springs, you can adjust the clearance and stiffness of the suspension, the car does not seek with full loading. Especially the effect is noticeable if you use them on bad road (gravel, pits, bumps, cords, primer, asphalt waves, railway moving, etc.). Also, if the wheel rubs on the arches, then you can get rid of it with the help of pneumatic products in the springs.

Blackstone pneumobalones are suitable for cars where the shock absorber is located separately from the spring. The sign ✔ means that the shock absorber is installed separately from the spring and the installation is possible, a sign ✘ - Cars with a rack MacPherson are marked, or where the installation of pneumas is not possible. Sign ✐ - There is an instruction / installation photo. To go to the instructions, you must click on the icon itself. The catalog does not make one hundred percent warranty that the pneumatic element is suitable for your car, as there are structural differences in the configurations of the model, or their modifications.

How to determine whether the Blackstone pneumobalon is suitable if there is no information in the catalog?

It is necessary to measure the inner diameter and the height of the spring in the usual state without a jack and without cargo (it is easier to carry out the measurement on the pit):

1. Make sure the car stands on a flat area, the springs are under the influence of body weight.
	2. Measure the inner diameter of the spring. If the spring has a conical or barrel-shaped measurement, it is necessary to produce in places of maximum and minimum diameter.
3. Measure the height of the inner space of the spring vertically without taking into account the full buffers (bumps) of the compression stroke - they must be dismantled.
	4. Check the internal space for the presence of bolts, acute items and convexities. If any, they must either be eliminated, or to close the bumps.
5. If there are holes in the lower lever and / or support from the body side with a diameter of more than 20 mm, they should also be closed with "W" and / or "F" with chippers.
	6. Pick up the most suitable pneumatic element on the tableboard below. Free space Height can always be filled with the help of chips "W" and / or "F". Excess space in diameter Pneumatic element will be filled with pressure.

Pneumonobalon sizes:

Doves And other components, including kits for the withdrawal of swaps at a convenient place (trunk, bumper, hitch, gas tank hatcher, etc.) are available in the section.

Take into account the fatigue of the springs when measuring. New springs can give an additional 5 cm in height. If the springs are given and you want to return the body for the previous height, you can use Blackstone pneumaticpers both with a replacement and without replacing the springs. If you did not find your car in the list, or you know the internal sizes of the spring, send this information to us in the mail, we will definitely publish it in the catalog.

Photos and video set sets:, and.

Pneumatic suspension kits for other cars, including for spring suspension :.

Ford (Ford)

C-MAX 2007 (CB3) ✔ Blackstone MHD Pneummobalon
Cougar 1998-2000 (MC) ✘
Escort. ✔
Fiesta 1976-1989 (AX) ✔
Fiesta 1989-1996 (CX) ✘
Fiesta 1995-2001 (DX) ✘
Fiesta 2008- (CB1) ✔
Fiesta / Fusion 2001- (CBK) ✔
Focus 1998-2005 (CAK) ✘
Focus 2004- / Focus C-MAX 2003 - (CAP) ✔
Focus 2008 - (CB4) ✔ Checked Suitable
Focus Cabriolet 2006- (CA5) ✔
Galaxy 1994-2000 (VX) ✔ Blackstone MHD Pneummobalon
Galaxy 2000- (VY) ✔
Granada / Scorpio 1985-1992 (CE) ✔
Granada / Scorpio 1992-1994 (DE) ✔
KA 1996- (CCQ) ✘
KA 2008- (CCU) ✔
KUGA 2008- (CBV) -? blackstone MHD Pneumatic Balls
Mondeo 1992-1996 Europe (FD) ✔
Mondeo 1996-2000 Europe (GD) ✔ Realms Blackstone MHD.
Mondeo 2000-2007 Europe (GE) ✔
Street KA 2003-2005 (CCS) ✘
TH! NK City 2000-2002 (CT) -?
Windstart 1994-2000 (WA)?
Escape 2008- Russia (R3) ✔
Everest 2006 (EU) ✘
Everest 2009 (EP) ✘
Everest / Endeavour 2003- (EV) ✘
Explorer 1992-2000 (EX) ✘
Maverick (LHD) 1993-1996 (Ml) ✔
MAVERICK (LHD) 1996-1998 (NL) ✔
MAVERICK (RHD) 1993-1996 (MR) ✔
MAVERICK (RHD) 1996-1998 (NR) ✔
MAVERICK 2000- (TM1) ✔
MAVERICK 2002- (TM3) ✔
MAVERICK 2007- (TM7) ✔
P100 1987-1993. (DP) ✘
Ranger 1998-2003 (ER) ✘
Ranger 2002- (EQ) ✘
Ranger 2006- (ET) ✘
Ranger 2009 (ES) ✘
TRANSIT (TT9) - Pneumatic suspension kit for Ford Transit :.
TRANSIT CONNECT 2002- (TC7) ✘

We offer a wide selection of pneumatic suspension kits for the series car Ford. Transit. All products are distinguished by high quality and comes only with proven manufacturers, which guarantees the reliability and durability of all parts.

If you did not suit the models from the directory of our site, the required pneumatic suspension kit for your Ford Transit can be found by consulted with our consultants. They will tell about the product products in detail and prompt how to measure the measurement and choose the corresponding model.

The suspension on the Ford transit can be installed independently. But if you want to be sure that everything is done correctly, enlist the guarantee and save nerves, contact our company.
Call 8-800-555-20-88

Pneumatic suspension on Ford Transit improves performance features The car allows to reduce the cost of repair and maintenance, and, therefore, increase the profitability of the freight.

The pneumatic suspension on the Ford Transit eliminates the seating and splitting of the body when loading, increases the life of the springs and the nodes of their attachment, increases comfort and improves handling when driving with cargo. After installing pneumatic elements (pillows), the car's weight is redistributed, which leads to the unloading of the springs and the elements of their mounts. Adjusting air pressure in pneumatic elements (pillows) allows you to select the optimal mode of operation of the air suspension depending on the loading of the car.

How is the pneumatic suspension on Ford Transit

Pneumatic suspension on Ford Transit is additional equipmentHer installation does not require changes to the car's design. Pneumatic elements (pillows) are fixed between the frame and the bridge with the help of special brackets. The pneumatic suspension control system is usually placed in the car.

To install, it is not required to completely redo the move. The most popular option is to mount a single-mounted pneumatic suspension on Ford Transit on the rear axle. At first, the brackets under the pillows are installed. The top is attached to the frame, the bottom - to the spersion sheet. During the work, it is necessary to do holes for bolted bolt connections. Next here are pneumatic cylinders. The hoses are connected to them. The compressor with the receiver is better installed in the cabin. In the open space, the place is limited, and in the body (if it is a booth) it may be damaged. Connect electromagnetic valves to the unit and display the control panel to the front panel.

On this, the installation of the pneumatic suspension in Ford Transit is completed. Tubes should be laid on the inside of the frame, attacking them on the clamps. We prolong the resource in order for the cylinders served for a long time (and this is half the value of the entire system set), you need to know some rules for the care of them. Rubber coating of pillows is very afraid of road reagents and dirt. Even small particles are capable of acting as abrasive at the joints of the parts of the pneummobalon. So that the pillows serve for a long time and did not descend, it should be cleaned from dirt periodically. And in winter - to handle silicone.

Pneumatic suspension on Ford Transit is installed easily and quickly. To install, you will have a fairly standard set of tools and basic car repair skills. If there is no possibility to install the kit yourself, we recommend using the services of a professional car service.

There are two ways to control pneumatic suspension: comfortable and economical.

With a comfortable version of the pneumatic suspension on Ford Transit is set together with a pneumatic suspension control system (sufficiently simplest). In this case, air pressure control in pneumatic elements (pillows) occurs with the key from the car's salon, and the pressure control in pneumatic elements (pillows) is carried out on a manometer.

In an economical version of the pneumatic suspension on the Ford Transit is installed without a control system. Then adjustment and control of pressure in pneumatic elements (pillows) is carried out through the nipple of the pneumatic system in the same way as adjustment and pressure control in the automotive bus.

Pneumatic suspension Aride on Ford Transit ( front-wheel drive FWD) (00-14), rear axle.

Description - Pneumatic suspension Transit

A set of auxiliary air suspension on Ford Transit is installed in addition to the standard car suspension and reduces the load on the springs. Installation of the air suspension will allow the Ford Transit to carry more cargo without loss of controllability, will save from sending the springs and their breakdowns, cut the body of the body and roll. Pneumatic suspension on Ford Transit (front-wheel drive) is a great solution for increasing the service life of the standard suspension.

The pneumatic suspension kit is designed specifically for Ford Transit and includes two pneumatic elements, mounting brackets to frame and bridge, fasteners, accessories for pumping from an external compressor, instruction.