West discs 17 radius factory. Wheel disk deficit for Vesta! Investigation Balancing as a necessary security condition

Good afternoon, dear zarulevitsy!I want to throw a relevant topic for the article. I owner Lada Vesta. SW Cross, and now for me the purchase of winter tires on disks is relevant. However, it turned out that AvtoVAZ used a non-standard disk with departure 43 and demands to use it only to avoid loss of warranty. Official disk is space 7.5 thousand, possible replacement Only one - for 6.5 thousand and even the manufacturer in stock only 1 (one) disk (consider that there is no replacement).Thus, the plant imposes a purchase of its unique disk on a clearly high price. Why not attract public attention to this and do not request the commentary of the plant? At least the plant could solve other replacement options. Judging by the forums, the people put the 15th and 16th wheels, risking the guarantee, because the imposed option is trally twice as expensive.With all respect, Andrew.

Dear Andrei! We tried to answer your questions from all possible positions.

Officially

Any manufacturer, not just AvtoVAZ, will require only those that are written in the instruction manual. On them the car passed factory tests and certification. As he behaves to "shoes" with other parameters, the manufacturer is unknown, and it cannot take responsibility for such a replacement.

To confirm this obvious, in general, I have nevertheless contacted the press service of AvtoVAZ and incognito called hot line Lada. Both sources were unanimous: only 17-inch tires and wheels with parameters specified in the operating instructions are allowed on the sedan and universal. Other options will be treated as a reason for refusing warranty repair chassis.

Sanctions

You can pay not only with refusal to free repairs. If the tire not approved by the plant notices the DPS inspector on the road, it is entitled to make a protocol on car inconsistency with the requirements Technical Regulations, paragraph 5.1 of which says: "Vehicles must be equipped with tires according to the operational documentation of vehicle manufacturers." And this is already a reason for stopping registration, if the fault is not eliminated.

Wheel marking is usually applied to the inner surface. If you are a scer Vesta Cross. In the same 17-inch wheels, but with other departure parameters, widths and diameters of the central hole, estimate the correspondence directly on the road the inspector, of course, will not be able. But the other diameter is already obvious, and will tell it on the tire.

An other diameter, except for the seventeenth, will also put the cross on the possibility. If you completely thicken the paint, there may be extremely unpleasant consequences in the event of a difficult outcome accident. After such, they often prescribe a lot of expertise and find out all the details. Non-standard wheels will pop up, and who knows how the investigators regarding this. But this is the theory.

Reality

Real life, as usual, has some differences. I called several official dealers of the Lada in Moscow and, introducing the owner of the SW Cross wagon, asked to advise the alternative to the native "shoot" by 17 inches. The answers were like a copy. Managers department of spare parts have not seen any problems in installing 16-inch wheels and were ready to offer options.

To the question in the forehead "And what with a guarantee?" Stewed and switched to the relevant specialist. And already a predictable answer sounded from the warranty: wheels will stand up, but the appearance with them on the service will refuse to refuse to repair the suspension. However, everyone was given to understand what it would not be happening. Would you believe them for the word?

Of course, you can put the trips to the season when your Vesta is shod in factory wheels. But the fact that dealers are woven not approved by the plant dimension, outrageous. Someone will buy them without asking any questions! And then in the same technical center, to his surprise, will receive a refusal warranty.

Do AvtoVAZ blame?

First of all, the wording "turned out" in the question of the reader is incomprehensible. Allowed by the manufacturer of the dimension of tires and wheels are indicated in the instruction manual, which is posted on the official site in public domain. If spending on consumables for the car are so important for the future owner, it is advisable to review prices even before buying a car.

It is necessary to admit that with the price of the original 17-inch wheel (about 7,500 rubles) AvtoVAZ really faded. Starting a dozen largest sites for the sale of wheels, I really found only one perfectly suitable option - kick a flanker. It is cheaper than a thousand rubles, which gives savings of 4000 rubles from the kit. What, in my opinion, not so little.

In the end, there is no obligation to make the winter set in the collection. Wheels too expensive? Buy only tires. For the money that he asks the Lada dealer for one disk, you can rebuild the entire car three or four times.

And if we speak quite frankly, AvtoVAZ is by no means alone in a desire to earn slightly. Similar "Divorce" for extra money, if you search, you can find hardly any car! And the case with the West Cross is not the worst: for a careful buyer, it is obvious before purchasing.

If you do not leave far from the topic of the chassis, I remember two examples. On French cars for a long time, alloy wheels were used without the central hole. They are impossible on a standard tire machine. I had to look for a workshop with rare equipment. Someone in the regions - sure! - There was only one way, to the official dealer with his queues and draconian prices. And for not unoriginal racks were not available. And this is despite the fact that last generation The C5 of their "snaps" and the knocks could not be remedied for years, and the owners of the machines changed several kits in a row.

Finally, a small hint: Write complaints and wishes, if something does not suit you. Only not in the "driving" log, but a direct manufacturer. In recent years, AvtoVAZ has not once demonstrated that he listens to customers. It is possible when the number of appeals reaches the critical volume, for Vesti in the version of Cross, the 16-inch tires and wheels are certified.

Deficit wheel disks For Vesta! Investigation of V.

To date, various discs on Lada Vesta are presented on the market. The main differences between them are the materials from which they are made, ways of manufacturing and fastening, dimensions. To properly pick up the car components, their sizes presented in the table should be known below.

T - index of permissible speed within 190 km / h;

N is an index of permissible speed within 210 km / h;

Et - the departure of the rim, which denotes the distance from the bustal surface of the disk to the middle of its rim;

incomplete load - the presence in the cabin of three adults, without cargo in the trunk;

full load - presence in the cabin more than three adults, or the presence of three adults in the cabin and luggage weighing 50 or more kg (depending on the capacity of the luggage compartment).

Fastening the wheel to the hub of the car is carried out with the help of four bolts through the holes on the disk. It has four holes, the centers of which are located on a diameter of 100 mm.

The easiest and cheapest option is steel stamped discs on Lada Vesta. They are made by punching the mold. External differences in detail depend on the characteristics of the stamp, according to its forms, the product acquires its final form. The main advantage of stamping is strength and resistance to external influences: scratching, shocks, scratches.

R15 from steel disks are provided by the manufacturer when buying a car in basic configuration. Recommended tire sizes 175/70 R15. You can buy stamping in many service centers and stores, after ordering them on the website of the store, where photos and prices are presented. Retail price in Moscow begins with 1300 rubles per piece and can reach 2500 rubles.

When buying discs, you should first clarify whether a fastener is included in the purchase price. Sometimes the fasteners need to be purchased separately.

Popular alloy wheels Lada Vesta is distinguished by a wide selection of design and diameter. They are made from a special alloy. In addition to the base metal of aluminum, the alloy contains magnesium, strontium and titanium additives. The casting process occurs under the influence high pressurewhich contributes to the rapid harvesting of the workpiece. With the help of computer simulation and milling, the part gets the final form.

The multi-level process of making cast drives explains them. high cost. They are lighter by weight, but have fewer resistance to mechanical damage.

Lada Vesta on casting is represented by the manufacturer in two versions:

• rake R15 recommended for tires dimension 175/70 R15 and 205/60 R15;
• r16 discs are suitable for tires with dimensions 185/60 R

On a note!

Alloy wheels 15 Radius on Lada Vesta are provided when buying a car in the configuration "Lux". For a fee as additional equipment Alloy wheels can be installed 16 radius in Lada Vesta.

You can buy alloy wheels on Lada Vesta in specialized centers and online stores, on the websites of which photos are presented. average price On the casting radius R15 2500 - 4000 rubles, depending on the manufacturer and design. The 16-inch rollers will cost the owner of the car more expensive - from 3500 to 6000 rubles per piece.

Alternative wheel sizes

In pursuit of beauty and unusual appearance, the owners of Lada Vesta set rollers of the seventeenth and eighteenth radii. They envisage the presence of low-profile rubber, which is very sensitive to the slightest irregularities of the road, which makes a trip to the car less comfortable.

R17 discs

Quite often there are vet cars with wheels with R17 radius. They look noticeably more than standard in fifteen inches. Recommended tire sizes for this type of casting 175/55 R17, 195/50 R17. External features are presented in the photo Lada Vesta on 17 discs. You can buy such shoes for cars for 5,000 rubles per piece, product foreign production With an exclusive design cost 15-17 thousand.

R18 discs

For the first time skating of this size were presented on the concept of Lada Vesta with tires 235/45. Photo of Lada Vesta on 18 disks clearly demonstrates sports design and car dynamics. R18 casting is much more expensive than its "younger brothers" - from 9000 rubles per piece.

Recently, it becomes very popular to combine contrasting colors in the design of the car. This trendy trend contributed to the production of rinks in different colors. On the Internet spaces you can find many photos with various combinations of car body colors and disk rim.

Disks on white Lada Vesta recommend to put a contrasting black color. Black cast looks profitably on the background of a white body. By the same principle, you can choose discs on. White rollers will be bright and attract the attention of others. Classic silver casting is suitable for machines of any color and is a universal option.

Among the numerous design innovations attract attention to weta discs with a bright red edging along the edge of the rim and on the spokes. They are suitable for any color of the car body, but preferably put them on a red car. This combination gives the car a sporty appearance and unique personality. Even in dense urban traffic, the car will stand out from a total stream and to pay attention to others.

What is affected by the size of tires and disks

The increase in the size of the tires and discs will affect the operation of the Vesta Lada:

• The increase in the diameter of the disk has a positive effect on the quality of the steering, the holding of the road, but reduces the level of comfort on the uneven road.
• An increase in the width of the disk will also improve steering And the deduction of the road, but will increase fuel consumption.
• Increasing the width of the tire is also for the better affect management, including on an uneven road, will improve the adhesion with the road (in dry weather). At the same time, the consumption of gasoline and wear of tires will increase, as well as affect the resistance to aquaplanilation. Noise level will increase.

In 2016, AvtoVAZ announced the creation Lada Vesta. and Lada Xray. In exclusive versions. The first cars were presented at the car dealership Lada "Exclusive". Innovation of models - 17 inches discs. To date, Lada Xray is already actively put such wheels, but Vesta is still being content with only 16 inches.

In the light of these events, a reasonable question arises: how to increase the wheel diameter affect the car suspension? AvtoVAZ does not give a response to this question. Let's try to figure it out on your own.

Maximum permissible size Discs for Lada Vesta - 195/55 R16.
The auto show was presented with Weste with Hankook 225/50 tires. Presumably the size of the West Wheels exclusive will be 205/50.

As a rule, an increase in the dimension of the disk has a positive effect on handling. This is due to the reduction of the fuel supply of the wheel in the side. Also increases the volume of braking mechanism.
By increasing the diameter of the disk on Vesta, the engineers most likely wanted to betray the "sharpness" of the control system.

It should be remembered that with an increase in the mass of the wheels, the speaker is lost. If the dimension changes are insignificant, as in our case, then the consequences are practically invisible.

However, how will the suspension be changed in the new version of Vesta?

Now the vests suspension is made in such a way as to balance its maximum driving performance. It greatly affects the smoothness of the machine and on its handling.

Thanks for the subscription!

Of course, everyone knows that an increase in the diameter of the disk is not always accompanied by an increase in the wheel. Sometimes the big diameter of the disk is dressed low profile rubber. In this case, only the appearance of the car, and, in part, handling. However, there is a significant minus - the irregularities of roads. Any pit or bump leads to damage.

Consider the inverse situation - with increasing size wheel Disc Increases the wheel itself. In this case, the car will slowly accelerate and slow down, but the maximum speed can increase a little.

The large diameter of the disk is not always a big weight. Here you need to look at the whole wheel in the aggregate. However, the weight of the wheel is 17 inches on new Vesta There will be slightly more than 16-inch. On the car suspension, we practically do not notice. Basically, it will be possible to feel changes on a bad road.

Car wheel - the necessary part, which in symbiosis with a bus is a device converting external energy in useful work By moving the vehicle. Each owner of the car must have basic information about this element and know which ones are rationally suitable for the purchased Lada Vesta. The following photos of the domestic new product will be presented. different wheels. Disks on Lada Vesta are divided into two types:

• The first type includes cast wheels, which are manufactured by the method of casting in the form of a certain diameter. Material for creation often appear: aluminum, magnesium, and also, in rare cases, titanium alloys. After the slowdown process, it is necessary to conduct a heat treatment session. The final look of the disks are obtained after mechanical stripping and staining process. The cost of such parts is the most optimal.
• Stamped discs represent the second type. They are made of steel sheets of the format of ST-3. Two halves with holes are welded and become integrity. Straighten with a sledgehammer or specialized machine. This item has a lot of weight, but it is easy to resist and pressure. The main minuses will be the susceptibility of corrosion and bad balancing, which can lead to unpleasant consequences When driving at high speed.

Interesting!

On the territory of the Russian Federation, aluminum plants in Krasnoyarsk and Sayanogorsk are engaged in the production of wheel details, as well as the largest concern for Titan's processing, which is VSMPO abbreviation. The first place in quality is occupied by Germany, Italy and the United States.

Effect on tire size and wheels

West discs cause a specific action to manifest some categories:

• An increase in the diameter and width of the disk, as well as the width of the tire significantly increases the overall view of appearance. It improves the adhesion with the road and the accuracy of the steering.
• The driver clearly will feel discomfort if it will move on disks of smaller size than they were installed. This lack compensates for the expansion of the tire itself.
• Noise from the road does not depend on changing the size of the wheels. However, with an increase in the width of the disk and the tire increases the consumption of fuel on any surface.

If you consider the photo of Lada Vesta on 17 disks, you can immediately note the addition of courageous dynamism and unsurpassed style. Accordingly, it is necessary to purchase and tires 17 sizes. One such automotive "shoes" will cost 5 000 r. And the goods from a foreign workshop with an exclusive style can cost big money (14-16 thousand rubles).

The photo of Lada Vesta on 18 discs found in the network immediately after demonstrating the concept car in 2015 at the automotive exhibition in Moscow. Such a volume of casting inspires the colossal respect for the product, as it creates the impression that the wheels are the most important detail.

On a note!

The eighteenth disk element and the wheel R17 are not installed for Lada Vesta sedan in the factory conditions, but the owner has the right to give an extraordinary look to choose and mount those. It is likely that such "shoes" at Sports-Kare or SUV from the domestic concern.

Wheels from the manufacturer and purchased by the owner

For the Lada West sedan, there are R15 discs and wheels R16. Stamped wheels are mounted only for the first option. They are installed on the cheapest modifications of new products from AvtoVAZ. Cast (R15 and R16) are available for more advanced and expensive complete sets "Comfort" and "Suite". The photographs clearly visible the difference between these elements. The vehicle operating manual provides useful data on wheel items on the axis of the chassis.

• Alloy wheels 15 Radius in Lada Vesta, installed by the factory manufacturer, are equipped with a capacity index of 560 kg (not confused with a capacity). Tire pressure at full and partial load is 0.21 and 0.22 MPa, respectively. These details are mounted today for all the configuration of the four-door sedan from the Togliatti concern. All these indicators are equally related to the "stamp" disks (fifteen radius).
• Alloy wheels 16 radius in Lada Vesta, put on the plant conveyor, have a large lifting index - 615 kg. Tire pressure is similar - 0.21 / 0.22.

On a note!

If the owner decided to change the wheels on his car, it is necessary to understand that 15-inch discs have a limit in the maximum speed index - 190 km / h. For R16, this indicator increases to 210 km / h. Winter tires Do not allow to accelerate vehicle Over the limit of 160 km / h. Neglecting instructions may entail an emergency.

Balancing as a necessary security condition

This procedure performed successfully is intended to be a guarantor of getting rid of a multi-mulite during a high speed and subsequent car crash. In addition to the steering wheel, shock absorbers and other elements of the chassis.

The balancing procedure is necessary at least once a year. It is mandatory when changing tires. The main reason for the wicker of the wheel becomes rubber wear and subsequent casting deformations. For operation, contact bus service.

Combination of the Lada Vesta Body Palette and Wheel Elements

Today it is very often engaged in the decoration of the car by combining contrasts and various shades in the design. The manufacturer went to meet the aesthetics lovers and began to produce casting in a diverse color decision.

So that the discs on the white Lada Vesta loosely looked at, recommend buying the wheels of the contrasting black tone. This interesting solution is easy to divide running part From the body itself. Discs on black Lada Vesta in priority should be white, which is bright and stylish to highlight your vehicle from a huge number of cars on the highway and in the city.

Where to purchase detail

Milling and "stamping" of ordinary diameter (R15 / R16) is sold on specialized Internet sites, as well as in the salons of the official supplier of spare parts from AvtoVAZ. Stamped discs on Lada Vesta are the cheapest in the assortment. Their price begins about 1300 rubles. You can buy alloy wheels on Lada Vesta in stores for 2,500 p. The range of this product on the shelves is huge, which will allow each owner to find a suitable wheel of his car.

R18 discs, as well as R17 wheels have a higher cost (from 5 000 r.) And low-profile rubber, which is very sensitive to the irregularities of the roadway. They are installed on the axis of the chassis part to visually allocate an attractive part of the car.

Lada Vesta on the casting from the freight on the stamped wheels is different best design and quality, so the consumer has a large selection field. Which of them buy, solves the potential owner. In addition, it is possible to first consider the desired photos, and after the product image is live.

The exterior style depends not only on the type of body color, some tuning elements, but also the appearance of the wheels, and in particular disks. However, approaching the recruitment of these components should be not only from the side of aesthetic values, but also comply with the size of the factory requirements of VAZ VESTA sedan 1.6 2015, as well as indicators performance characteristics. In the latter case, on the background of stamping, products made of alloy alloy metals are largely won. However B. financial Plan Not every motorist can afford them.

Read more about the assortment presented

Regarding forged products, alloy wheels in Moscow are inexpensive structures, but they are expensive than motorists compared to steel rims. However, they are in great demand in connection with the possibilities of casting technology to produce real masterpieces on the style of alloy products. Lightweight designs are able to become the main highlight of the exterior of VAZ Vesta sedan 1.6 2015. They have a worthy resistance of corrosion, which you can not say about steel disksAnd demonstrate excellent running quality.

Machine rims made of aluminum or titanium alloy, which are valued by excellent physicochemical properties. At the same time, in terms of strength, these alloyed metals are not particularly inferior to steel. With alloy wheels, the owner of VAZ Vesta Sedan 1.6 2015 may not worry for the safety of high-speed indicators.

In addition, alloy wheels are valued by fuel efficiency, which is ensured by the ease of construction and the low rolling resistance coefficient. In addition, they have excellent thermal conductivity, which makes it possible to prevent the probability of overheating brake and systems. This property allows drivers to feel somewhat more confidence in the safety of movement. Alloy products are balanced and have a high accuracy of geometric parameters.

Choice complexity

Such a wide range of discs, which is offered today domestic and foreign manufacturers create certain difficulties when buying components in Moscow. After all, sometimes brands for the same specifications Products exhibit completely different prices. However, is the quality of the quality indicators?

On the website of the Wheel Dair online store, you can familiarize yourself with various reviews of motorists who have already managed to evaluate all the advantages and disadvantages of various discs on Vaz Vesta sedan 1.6 2015 and make your choice. You can also consult with the competent managers of our store, which can not just pick up for you optimal option Wheels in quality and cost, but also answer all the questions that arise.

When choosing disks, it is worth noting the importance of the quality factor, which you move. If you have to overcome the extreme difficulties of relief daily, it makes sense to give preference only by budget stamped components.

If you have a limited budget can always be purchased more affordable by price, but no less high-quality replica. Moreover, today many brands create copies of original wheels, which are not inferior in the performance of the operational characteristics of "native" details.

Why should you buy discs in Moscow?

We propose not to waste time for long searching for reliable distributors of automotive components and order wheel items in the Wheel Dair online store. We have a wide range of disk models different species From tested by manufacturers. We are sure that you will be satisfied with the quality of our service and directly acquired goods.