What kind of oil to pour into Nissan Qashqai 2.0. Recommended engine oil for Nissan Qashqai. Changing the lubricant

home / Machine Reviews

The oil change procedure in this manual is the same for all first generation Nissan Qashqai J10 bodies, models 2006, 2007, 2008, 2009, 2010, 2011, 2012 and 2013 release.

Consider detailed replacement oil and oil filter for gasoline HR16DE, MR20DE and diesel K9K, M9R.

Choice of oil and filter

According to the regulations Maintenance, during normal driving at different distances, the oil in the engine should be changed every 15,000 km. This is about once a year.

How much oil is needed:

Engine 1.6- 4.3 liters

Motor 2.0- 4.5 liters

In general, you cannot do without a canister of 5 liters. It is poured at first - boldly 4 liters and then pour on the dipstick (more details below).

The cost is different everywhere. There are also cheaper oil analogues, as well as small containers for topping up.

You can buy bottled oil at specialty oil stores. Mobil 5W-40 is well suited - 400 rubles. for 1 liter.

Choose a simpler oil filter. From everything that will be, take the one that is cheaper, there is no difference.

Most often, filters are purchased with article numbers:

15208-9F6OO(NISSAN Oil Filter made in UK)

15208-65F0A(NISSAN Oil Filter made in Japan)

The price range is large, from 90 to 500 rubles.

A drain plug gasket can be purchased within 50 rubles. There is also a range of prices.

We take any with the article 11026-01M02(NISSAN Plate Lock-Kit)

Armed with all the acquired and free time, we proceed to self-replacement... In local car services, an oil change service will cost around 500 rubles.

Replacement

The oil change operation is done on a pit or a lift. It must be conveniently located under the car.

First, unscrew the boot mount. Left and right with a head 10.

In the center, it is held on a clip. To remove it, you need to pick up the central part of the clip and pull it down by about 8 mm. After that, the clip is easily removed from the hole.

Slightly bending the boot, we see the bolts for securing the front protection, unscrew the head by 13.

The fastening bolts at the back are loosened with a similar wrench. After that, remove the engine protection.

The oil should be changed with the engine fully warmed up. To do this, we start the engine and wait until the temperature reaches the operating level or the cooling fan turns on.

Unscrew the filler cap on the engine from the engine compartment. Then you need to place the container under drain plug the engine pan and unscrew it completely.

Oil drain plug for 14. Pour the main part of the oil into the prepared container.

After the oil has completely drained from the sump, i.e. it will drip extremely rarely, we remove oil filter(located on the front of the engine) and let the remaining oil drain from the system.

New consumables.

We clean the place where the filter is installed with a rag. Lubricate its seal with oil and wrap it up to light resistance, and then tighten it 2/3 of a turn.

Next, replace the drain plug O-ring and screw the plug into place.

We place the ring on the cork with a platform with a cutout to the cork head, a solid platform to the pallet.

Plug with a new washer.

It remains only to pour new oil into the system.

Despite the fact that the canister with original oil has a convenient neck, it is difficult not to shed at the very beginning, so you should use a funnel, preferably a high one.

If there is no funnel, then it is easy to make it from an empty and clean plastic bottle of 1.5-2 liters.

The main principle is not to overflow.
Therefore, when 4 liters are poured, you need every 100 grams. check the level on the dipstick.

When the oil level on the dipstick starts to reach the second mark, you can complete the top-up. We close the filler cap and check the oil level according to the BC.

To do this, you need to turn on the ignition and, when the Oil Good inscription appears, press the "i" button on the steering wheel or TRIP on the instrument panel. The level should be 4-5 divisions out of 5.

After that, you need to reset the service mileage, which is displayed on the BC when the ignition is turned on. On the restyled version, it is reset through the corresponding menu when turning TRIP.

On pre-styling, you need to do the following:

1) With the ignition off, press and hold the TRIP button on the dashboard;
2) Turn on the ignition while continuing to hold TRIP;
3) When the service mileage value with a wrench starts flashing, release TRIP and press it again. In this case, the value of the service-to-service mileage will drop by 15,000 km;
4) To change the value of the service interval, rotate the TRIP in different directions depending on the value.

Video

Videos from youtube.com | by tim tims

In order for the engine to be stable and run in excellent quality, the oil should be changed in a timely manner. According to the recommendations of manufacturers, oil for other types of engines (both for a diesel engine and for gasoline) must be replaced every 15,000 km or every time you undergo scheduled maintenance. If your car is serviced only by you and rarely goes to the service, then it is better to replace it after 8,000-10,000 km.

Consumable selection

All this oil for Kashkaya DCI with a viscosity of 5W-40 (only it is suitable) is sold in 4 liter cans (not for 5 liters). You will have to buy another 1 liter to refill your diesel.

Engine volume

Depending on the engine in Nissan (1.6 or 2.0), a different amount of lubrication will be required. In the 1.6 engine box, 4.3 liters must be poured, and in 2.0 the oil volume is 4.5 liters.

Oil filter selection

After deciding which oil to use, you need to buy an oil filter. It is always changed when the planned Nissan Qashqai. Manufacturers advise to install the original one: article 15208-9F6OO from Great Britain, and article 15208-65F0A from Japan. They cost from 400 rubles.

Not only the original is suitable. We will select the suitable ones:

Filtron OP 595 costs from 170 rubles.
MANN MF W67 / 1 costs from 350 rubles.
Sakura C1823 costs from 180 rubles.

These are the most popular analogs with good reliability.

Selection of O-rings

Together with changing the oil to Nissan Qashqai, the manufacturer also recommends changing the O-ring in the drain pipe. If this is not done, then it is possible that oil will leak from under the plug.

Buy original product Nissan 11026-01M02, which costs from 30 rubles. There are also analogs that can be used if it is not possible to put the original:

LEX WW0829 - 30 rubles.
OKHNO YH0114P - 50 rubles.
Adjusa 18,000,900 - 25 rubles.

Changing the lubricant

After purchasing all the necessary elements, the Nissan replacement can be carried out independently.

DIY replacement process:

Take a socket or spanner size 10 and unscrew the engine protection. Then pull out the central protective clip.
Fold back the protection and unscrew the two bolts that are in front. To do this, use a 13 wrench. The same should be done with the rear bolts and remove the protection.
Place a container under the drain plug where the grease will be drained. Unscrew the plug and discard the liquid.
When the Nissan oil is drained, you need to remove the oil filter. But you should be careful, as it still contains grease.
Change the gasket on the drain plug and discard the old one.
Pour in new filter Little lubricating fluid and anoint the rubber gasket with it. Then fasten it.
Now you need to pour 5 liters of grease into the filter. Check the level with a dipstick. Then pour to the normalized state, screw on the lid.

Increased product consumption

A high oil consumption is a consumption that exceeds 0.5 liters per 1000 km. The motor eats more grease due to the increased speed on the engine, therefore, the tolerance of 3000 rpm should not be exceeded so that oil for Qashqai is not consumed more than the norm. It is necessary to check the compression in the cylinders, the crankcase ventilation system, and possibly clean the valve. And then replace valve stem seals and valve seats.

There are also cases when the lubricant is not eaten, but it could simply not be refilled when replacing it.

Check the lubrication in the engine strictly on a level surface so that the results are accurate.

Experienced drivers often say, "I know why the engine is constantly over-eating." They give examples of such situations on the forums and give advice:

They can eat oil on oil seals that are leaking. It is very easy to check this: there are oil smudges under the hood.
Leakage through the gasket in the cylinder block occurs due to improper tightening of the power bolts or simply overheating of the engine.
There is a gasket on the oil filter, there may be a leak through it. When replacing the filter, lubricate the O-ring with lubricant and tighten the filter tightly.
There are such valve seals that are installed in the engine. Leakage can occur through them.
The oil scraper piston (control) rings are worn out, which eats the grease.
The problem is overheating piston rings which can increase oil consumption.
An increased gore of oil appeared due to the flutter of the ring. This is due to a decrease in the elasticity of the compression rings.
Coking of piston rings. Such rings cannot seal either gases or lubricants. That is why the engine eats more lubricant and the compression decreases, but often only one or two cylinders. Oil consumption due to this problem may occur in drivers who use low-quality engine oil by car Nissan Qashqai. That is, the product has a very weak washing ability, or it has lost this ability due to prolonged operation. Therefore, it should be reminded once again that the best solution is to use an original consumable that exactly fits all requirements. This will help avoid such problems. Russian car dealers often use poor lubricant products that do not meet the requirements.
Destruction or breakage of the piston valve bridges. This can be due to increased leakage of lubricant into the cylinders or deterioration of the seal of the combustion chamber. More than necessary liquid with boat gases flows through the ventilation system.
The reason why they eat oil liquid cylinders is covered in their wear. This is not difficult to detect. You should check them for scratches, scuffs, chips, it is still possible to increase the diameter.
Driving in an elevated state of lubricant viscosity.
Delayed combustion in cylinders.
Undesirable modes of engine use affect the oil intake. The gasoline engine, which often runs at high rpm and load, eats much more consumables.

Nissan Qashqai- a compact urban crossover, beloved by Russians. Its popularity is due to its balanced characteristics and quality components, as well as timely maintenance, using original parts... The most important part of a car is by far the engine. It is better not to save on its maintenance, and fill only with proven oil approved by the factory. In this article, we will look at how to choose the right oil - separately for each version and generation of Nissan Qashqai.

When choosing an oil, you should be guided by the parameters specified in the Nissan Qashqai user manual. For example, you should pay attention to the type of viscosity, grade and oil change period. There is an oil specially formulated for the harsh frosty climate, and such lubricants should not be used when high temperatures... A lubricant made for use in the summer is only designed for high temperatures overboard cars, and at low temperatures, this oil will quickly thicken, and as a result, there will be problems with starting the engine. Multigrade greases are very popular as an alternative to summer and winter greases. But in this case, you should pay attention to maintaining the temperatures with which the all-season works. For greater clarity, oils were divided into mineral, synthetic and semi-synthetic. For example, semi-synthetics support a narrow temperature range, that is, they are designed to be used only in certain weather. Synthetic oil- more fluid and less dense, and better suited for low temperatures, but also suitable for summer conditions. It costs more, but is considered more versatile. Mineral oil can be filled only as a last resort, for example, if there is a high mileage. It is mainly used in older motors.

As for the brand, you can choose any company recommended by the manufacturer. Such oil will meet Nisan standards anyway and design features Nissan Qashqai engine. A clear sign that the oil is approved by Nisan is presented in the form of a tolerance indicated on the product label.

Now we will consider the standards and types of oil separately for each modification.

Nissan Qashqai J10

For HR16DE and MR20DE engines:

original motor Nissan oil
API - SL, SM
ILSAC - GF-3, GF-4
ACEA - A1 / B1, A3 / B3, A3 / B4, A5 / B5, C2 / C3

For diesel engines K9K Euro 4 without particulate filter:

ACEA - A1-B1, ACEA - B3 / B4

For diesel engines K9K Euro 4 with particulate filter:

ACEA - A1-B1, ACEA - B3 / B4
Low Saps

For K9K Euro 5 engines with particulate filter:

ACEA - C4 Low SAPS (means low ash content)

For M9R diesel engines without particulate filter:

Nissan Genuine Lubricant Product ACEA Standard - B

For M9R engines with particulate filter (diesels):

Nissan ACEA branded oil - C4 Low Saps

For R9 M motors:

Nissan ACEA branded oil - C4 Low Saps (low ash content)

According to official data, including recommendations dealerships Nissan, Qashqai owners should fill with SAE 5W -30 for gasoline engines. If this parameter is not indicated on the label, then it is necessary to select the product for a certain ambient temperature.

For diesel engines K9K the most preferred option would be SAE 5W - 30.
For diesel engines M9R without a particulate filter, 5W-40 or OW-40 lubrication is required
For diesel engines K9K and M9R with particulate filter- 5W-30 with low ash content (Low Saps)

Nissan Qashqai J11

For HRA2DDT engines:

Nissan branded oil
ACEA - A3 / B4

For MR20DD motors:

Nissan branded grease
ACEA - A3 / B4

For K9K engines:

Nissan branded oil
ACEA - C4 (quality class)
Low Saps (low ash)

For R9M engines:

Nissan branded grease
ACEA - C4
Low Saps

For gasoline engines: the most preferred option is 5W-40 grease
For diesel engines K9K with particulate filter - 5W-30 Low Saps
For diesel engines R9M - 5W-30 DPF Low Saps

Based on the above, you can make sure that the choice of oil should be taken very seriously, and only the recommended parameters should be taken into account. For Nissan Qashqai is better use oils labeled Low Saps. It is also necessary to take into account the correspondence of the temperature ranges in which the car is used. There are separate parameters for diesel engines - they are more stringent than for gasoline engines.

Often motorists ignore the information in the manual for the car, violate the timing of changing the lubricant, fill in a car oil that is not suitable for the type, class or season. Why it is important to use the recommended engine oil for the Nissan Qashqai, we will explain in this article.

When choosing engine oil for Nissan Qashqai, it is worth considering the recommendations of the car manufacturer. The necessary information regarding the type, class, viscosity of the car oil, as well as the timing of its replacement, are set out in the operating instructions. vehicle. Special attention it is necessary to pay attention to the viscosity characteristics of lubricating mixtures. Liquids developed for the winter should not be used at very high temperatures overboard. A lubricant developed for the summer does not withstand too low temperatures and begins to crystallize. All-season oils, are a kind of alternative between the two previous types of lubricants, but when buying an all-season one should pay attention to the temperature at which the liquid can be used. For example, semi-synthetic motor oils operate in a lower temperature range than synthetic ones. It is recommended to pour mineral liquids into motors with high mileage.

The recommended engine oil for Nissan Qashqai meets the technical characteristics and design features of the engine of the specified car model. According to the tolerances, the buyer can understand that motor fluid suitable for a specific brand of machine, ensures normal operation and protection of the motor. If the engine fluid has been tested, for example, on Nissan Qashqai and meets the requirements of the car manufacturer, then the appropriate tolerances will be present on the oil canister.

Nissan Qashqai J 10 2006-2013

Oil characteristics

According to the manual, you need to pour engine oils that meet the following requirements:

In HR16DE or MR20DE car engines:

original NISSAN motor fluid;
according to API standard - SL or SM;
according to ILSAC specification - group GF-3 or GF-4;
according to ACEA - A1 / B1, A3 / B3, A3 / B4, A5 / B5, C2 or C3.

For K9K Euro 4 power units without particulate filter:

original lubricant NISSAN;

For K9K Euro 4 engines with a particulate filter (for some vehicle versions):

according to ACEA - A1 – B1 (with parameters corresponding to the ACEA group - B3 / B4);

For K9K Euro 5 engines with particulate filter (for some vehicle variants):

according to ACEA classification- C4;
"Low SAPS" (having a low ash content).

For M9R engines without particulate filter:

original NISSAN engine oil;
according to ACEA standard - B

In M9R car engines with particulate filter (for some vehicle variants):

NISSAN branded grease;
according to ACEA specifications- C4;
"Low SAPS" (having a low ash content).

In R9M motors:

original NISSAN engine oil;
according to ACEA standard - C4;
"Low SAPS" (having a low ash content).

Refueling capacity

Oil viscosity

For diesel engines, the following requirements for oils in terms of viscosity characteristics:

It is preferable to use SAE 5w - 30 in the K9K power unit. If such oil is not available, then using scheme 1 it is necessary to select the appropriate fluid.
For M9R engines without a particulate filter, only 5w - 40 or 0w - 40 can be used.
For K9K and M9R engines with a particulate filter (for some vehicle versions) or R9M, use only 5w - 30 lubricants of the "Low SAPS" group. (low ash).

Scheme 1. Classification of lubricants by viscosity characteristics for gasoline engines or K9K engines without a particulate filter, depending on the ambient temperature range.

According to the scheme, you need to use car oils:

5w - 30v temperature range-30 ° С (or less) to +40 ° С (or higher);
10w - 30; 10w - 40; 10w - 50 under conditions of -20 ° С to +40 ° С (and more);
15w - 40; 15w - 50 in the temperature range -15 ° С to +40 ° С (and more);
20w - 40; 20w - 50 at -10 ° С to +40 ° С (and more).