Replacing the clutch Ford Fusion with their own hands. Ford Fusion. Replacing the drive belts of the aggregates to change Ford Fusion

One of the most sought-after cars today is the Ford - Fusion model. Despite the simplicity of the design of this car, it also has weak places and disadvantages, which you need to know every future owner. After all, these knowledge will help make right choice And when buying, to save a significant amount of cash.

The weaknesses of Ford Fusion 2005-2012. release

• Gasoline pump;
• Timing belt;
• Tube gur;
• Robot;
• Bendix starter.

Now more ...

Gasoline pump.

One of vulnerable seats FORD FUSION. It is a fuel pump. On average, this unit fails after 80-100 thousand km. But it is worth paying attention to that very often the fuel pump fails and the less specified mileage (in the area of \u200b\u200b40-50 thousand km) due to the fact that not rarely the owners of these cars exploit the car with a sufficient level of gasoline in the fuel tank. This unit is not cheap and therefore, when buying a car, it is necessary to interview the driver when the last replacement of the fuel pump was produced. And when the ignition is turned on, listen, on the absence of foreign crops, whistles, etc. In the work of the fuel pump.

As with other brands of cars with belt drive timing, the belt is a weak place. But it is important to know that in this car The belt can be replaced and installed not at all in a row auto service (special equipment required). Therefore, when buying a car, it is important to ask if the belt was replaced or not. Especially on cars with big mileage Unambiguously need to make sure that. Otherwise, this is to be a future owner, and accordingly, with all the flowing costs and loss of precious time.

A common fusion disease with mileage is a flow tube GUR. This is due to the design flaw of the manufacturer. The fact is that during vibrations of the tube and redox reactions, corrosion of the tube will grow on the connections. If there are no frequent phenomena on cars with small mileage, then with a large mileage, these are massive problems.

Robotic gearbox.

When buying a fusion with robotic box Gears need to be responsible for checking this unit. It is necessary to do this because this box does not have the most good reliability and when the car runs more than 70 thousand km. These aggregates begin to show a lot of problems and faults. With trial ride, you must pay attention to the time of shifting. Make sure there are no crusts and knocks at the same time. It is important to know that the repair of robots in these cars will turn into a solid amount.

Bendix starter.

No less problems also delivers the Bendix starter. The car can start from the first time or from the second, but not even from the fifth. Therefore, when you purchase you need to make a car several times. Of course, in the worst version, the car does not start at all, as the Bendix will stop moving and engaged with the flywheel. And in any case, this is an age sore of fusion and not critical, but pay attention to it. It will not require the replacement of some details, and you can simply be limited to the cleaning of the benks. But the seller should talk about it (to reduce the price of the car being purchased), as it will require forces and time for this.

Less frequent malfunctions:

• Gap a plastic intake manifold;
• Leak pumps;
• On the "robot" and the manual transmission of the gear selection rod;
• On the "robots" subding the rods of the actuator servo actuator;
• Refusal of the motor door lock drive drive;
• Refusal of the electric motor drive of the rear wiper;
• The failure of the heat constituent of the heater;
• Hub bearings;
• Frequent burning of near light bulbs.

Basic Ford Fusion Second Generation:

1. Crickets in the cabin;
2. Weak noise insulation;
3. Rigid suspension;
4. Absence of armrest;
5. The gas tank hatch opens with a key (freezes in winter);
6. Weak LCP;
7. No steering wheel adjustment;
8. Skyrplay rear sediments.

Conclusion.

From all of the foregoing, it can be said that when choosing a used Ford Fusion, it is necessary to carefully make the car diagnostics before purchase, considering that when there is more than 100 thousand km run. Fucious has many faults. In addition to those mentioned in this article.

P.S: Dear car owners. We will be grateful if you tell about the comments about weaknesses And the shortcomings of your fusion identified during operation.

Weak places and basic flaws of Ford Fusion 2nd Generation Was Last Modified: December 7th, 2018 by Administrator.

Purpose air filter Car in the cleansing of an air motor cylinders. Thanks to the purified air, the quality of the mixture is improved, the wear of the contacting parts of the engine decreases. For long-term operation of the motor must be performed on the replacement of the Ford Fusion air filter. The article contains information on how to independently replace and that it will be needed.

The air filter consists of a plastic housing and filtering paper. For better placement of the filtering material inside and dense adjacent to the walls, it is sealed with special polymer rings. Passing through such a design, the air flow is cleaned of dust particles and dirt, which eliminates the contact into the engine of contaminants that can harm it.

Over time, the filter passes the air worse, as it is increasingly polluted. There is less air to the formation of air-fuel mixtures, an oxygen starvation occurs. This situation leads to the fact that the engine loses cravings, the car becomes less dynamic, moreover, this is reflected on the health of the driver and passengers. An error message may appear on the instrument panel. You can avoid such problems if you change the filter element in time.

Replacement recommendations can be found in the manual vehicleBut at the same time it is necessary to take into account the conditions in which the car is operated. If the surrounding air is strongly contaminated, the replacement is performed more often than the timeline recommended by the manufacturer. When operating under normal conditions, the filter changes after 10 thousand mileage, if the conditions are heavy - after 7-8 thousand kilometers.

May be required frontal replacement Air filter, as it comes to disrepair from the accumulated condensate inside the housing formed due to the constant motor temperature difference.

[Hide]

Instructions for replacing the filter with your own hands

You can replace the old Ford Fusion Air Filter in the service center, but the procedure is quite simple, therefore any motorist can be performed. Many drivers, using leadership, make a replacement with their own hands. Sometimes the air filter has to be removed to provide access to other engine aggregates, so the acquisition of experience does not prevent.

What do you need?

For the procedure, the following materials and tools will be needed:

• new air filter if the old cannot be cleaned;
• crosshead screwdriver;
• screwdriver
• spanner with a face head for 8;
• key by 10;
• plangies;
• pure rag;
• fixtures for purging with compressed air.

Steps

First of all, for the replacement procedure it is necessary to raise the hood.

First, two corrugated pipes are removed, which enters the air. It is disconnected by the clamp, holding the hose, which is from the nozzle, which is located on the air filter housing.

The disconnected hose is removed to the side. The mounting clamps should be checked for integrity, in case of damage, they must be replaced.

At the next stage, the crankcase ventilation hose is dismantled.

We begin dismantling from unscrewing in front of the housing of two bolts by 10.

After that, you should take the housing for the back of the closer to lobby glass And pull it up. In the case there are two ear, which includes pins, thanks to them it is kept, so it is necessary to pull stronger. You can first remove the left side, and then right.

When the housing is removed from its landing place, it must be turned over and unscrew 10 bolts that hold the lid. To speed up the process, you can use the screwdriver.

Removing the cover, take out the filter element. If it is not very polluted, it can be cleaned with compressed air using a special device. Pulling paper cassettes need to be taken care to not damage them.

With severe pollution is installed new filtersinging element.

Before installing a new element, the inner part of the case should be cleaned of dirt and dust with a clean puffed cloth moistened in water. After that, the new filter is installed in the housing and securely secured.

Together with it, you can replace the filter of crankcase gases, which collects oil evaporations and other contaminants flying from the engine pallet. It is a small sponge. Place its installation should be cleaned special tool. You can not search for the original filter of crankcase gases for Ford Fusion, and replace it with an ordinary sponge for dishes. The sponge is cut in size so that it does not hang out in its landing place.

Further assembly steps are performed in reverse sequence. The lid returns to the place and is screwed by bolts without an effort. The assembled body must be installed on the guides and click on its edges. Then screw two bolts, two air nozzles and crankcase hose are attached. Clamp should be snugged with pliers, as it is inclined to deformation. If it is damaged, then it must be replaced.

Thus, by performing a replacement with your own hands, you can save costs going on.

Video "Replacing air filter"

This video shows the replacement of the filter element on Ford Fusion 2010.

He justified his name and compatible into himself what could not be achieved from a crossover, nor from the wagon, nor from a compact city car. For him, they even came up with a separate class of cars - UAV, Urban Activity Vehicle, that is, a car for an active lifestyle in the city. Ford Fusion is built on the basis of the Fiesta and this makes it a little simplifies its repair, although even after years, the car holds a cast. There are problems, like every elderly car, but fusion bypasses them with your own ways. Yet, sometimes you need to help him.

Key Features Ford Fusion, Body and Engines

The Fiestovskaya base and the traits of the crossover merged into the Ford Fusion into one ammunition, which is quite tightly kept pile. Spacious salon I. big trunk Added a car of fans that do not particularly pay attention to the harsh plastic salon. The loading height of the cabin is only 53 cm, and the volume of the trunk is 337 liters, if not adding the backs. Without seats, the space in the trunk increases to 1175 liters, as for the class of class B is a success.

We had only 1400 and 1600 cubic motors have been available, although there are two more aggregates in Europe - equivalent economy turbo diesel engines. They also come across on our roads, but not as often as the cars delivered officially. In the database, the car had a standard, simple and reliable 5-speed mechanical transmission. There was an option to use a robot in a pair with 1,4-liter gasoline and diesel carsBut he did not use special demand. The suspension seemed too annoying to many when it reminded of bumps, but for the loaded car it was not critical. But in turns, the car was superb in turns, not inferior to the Shrins Fiese.

Ford Fusion Design Disadvantages

The most common occasion for warranty appeal to the officials for owners of gasoline modifications was the failure of the ignition coil. In Europe, not all began smoothly, because a lot diesel cars It was revoked due to problems with the fuel system and the pump. Release cars 2003-2004 had frequent problems With an unfortunate way out of order, which, though, immediately changed under warranty.

The transmission has always been at the level if you comply with the service regulations, but on some cars that have accounted for gravity, there was a previously burned clutch before the deadline, and at high loads could fire the block head gasket. The inductive ABS sensors are not very like dust and need to be cleaned often. The lounge of the cabin in low-cost modifications was wiped pretty quickly. Otherwise all ford diseases Fusion is treated as it occurs. We will look at the main reasons for interference in a tightly shot down body Urban FCTivity Vehicle Ford Fusion.

Replacing the oil in the engine and transmission

Actually, with a substitute for oil, everyone who drove 30 thousand km to Ford Fusion. Drop the oil on the hot engine until it has cooled. To access the filter, it is best to remove the protection motor compartmentIf it is installed, then full freedom opens for action. It is simply removed, it is enough to unscrew four bolts. When you unscrew the plug, you should look at the sealing ring. You never know what.

Under the protective casing, you will not always see oil drips. Moreover, the ring is not eternal and can withstand four oil replacements from strength. And when the protection is installed in place, it is necessary to control the air conditioner tube not pulled out of contact with time.

Service PPC Ford Fusion

IN mechanical gearbox The oil does not change, so it is enough to check its level. Level control tube hides behind a plastic casing that can be removed by folding four latches. There is another similar nut, she fixes the rod, so it is better not to be confused. The nut the lock is slightly below the cork. Do not confuse nuts, because when weakening, the fixing nut will simply weaken the locks and they will fall into the CTP Carter. Then you have to shoot and disassemble the box. The oil should be at the level of the lower edge of the fuel hole, if less, then only the native - WSD-M2C-200-C is addressed.

Automatic box requires special attention. But oil in it is also in the idea of \u200b\u200blife, but blindly to believe it is not necessary if there is no desire to carry out expensive repairs. Mark. corporate oil - WSS-M2C-924-A. Usually, vigilant and economic drivers change the oil after 100 thousand runs, but if during revision it shakes the burner, it is better not to pull, but replace it immediately. It will not work all the oil without dismantling, but if about 3 liters fall out, then this is already success. The same need and add. Next, consider some nuances who cause Repair Ford Fjuzn with their own hands on the chassis.

Pretty frequent procedure in difficult operating conditions - replacement of a shruss on Ford Fusion. Time procedure takes enough, but if you do everything with the mind, you can do without unnecessary televitations. On the car were installed in different time Pomegranates with different number of slots, so before changing the Sls on Ford Fusion, you need to know exactly this parameter. No special tools will be required for this, but only accurate compliance with the instructions will lead to a quick and trouble-free replacement. Everything is simple:

Installation is carried out in reverse order.

Typically, the replacement of shruses and wheel bearings is carried out if necessary, and the rear wheel bearing can be replaced in case of waste of studs when replacing the rear rear brake shoes. This happens if the lubricant and the care of the back bridge did not pay sufficient attention when passing the regulatory.

Generally, car Ford. Fusion is an excellent assistant in a big city and over time does not lose its relevance.

The process of replacing the timing belt at the Ford Fusion is long, the professional will take about 2 hours. Despite the seeming simplicity, we strongly do not recommend pursuing the process of replacing the timing belt independently, in garage conditions. Do not save on repair Ford Fusion. For this you need experience as well as a set of special ford tools: Mounting fingers distribution and crankshaft, as well as the lava lock.

The phased process of replacing the timing belt at Ford Fusion can be found on the pages of motorists forums, as well as in the printed manual. At the same time they fall some important momentsthat need to be considered when replacing the timing belt. So, for example, when the belt is removed, the engines shafts cannot be rotated, so as not to knock down the valve settings. Before working, we advise you to temporarily remove the candles. And, of course, the replacement of the timing should be carried out only with a disconnected battery.

Unscheduled replacement belt timing

In some cases, continue to move on the car is impossible, because The timing belt is in critical condition. If you have noticed oils of oil on the timing belt, or cracks, bundles, or obviously worn teeth with inner Belts, then it is subject to replacement immediately. At any time, it can burst, while the belt residues can get into rotating elements of the mechanism, causing a jam. In the best case, the belt will simply stay nearby, otherwise it can reach the overhaul of the Ford engine.

Signs of weak tension of the timing belt

Of course, not every car owner Ford Fusion regularly peeps under the hood to check the state of the timing belt, especially from the inside. But this is necessarily masts in a car service when the Ford maintenance is passed after the Ford Fusion diagnostics.

However, without waiting for the visit to the car service, you can independently notice some that indirectly indicate the weak tension of the timing belt:

• fuel consumption (at least compared to previous periods of the life of the car);
• loss of engine power, weak acceleration.

These signs can cause other "diseases" Ford Fusion, for example, a fuel filter clogged. Then it will take replacement Ford Fusion Filter Filter. Only the computer diagnostics of Ford will make it possible to accurately determine the cause.

Straightening belt timber

Despite the fact that the timing belt "wings" hundreds of kilometers for its service life, in fact he is quite fragile. Despite the fact that the belt is based on strong cord threads, the belt material itself is an elastic rubber. The combination of these two materials gives the timing belt with a huge wear resistance, but if it is properly tensioning during replacement.

Moreover, rubber, which is used in the manufacture of the timing belt Ford fusion is subject to destruction when contact with aggressive substances, such as, for example, gasoline and automotive oil. Therefore, as stated earlier, if you notice traces of fuel and lubricants on the timing belt Ford Fusion, get ready for its replacement.

Details of the clutch of any car are constantly subjected to gradual wear. With long-term operation in front of any owner Ford Fusion with mechanical box Sooner or later, the clutch replacement question arises. This procedure is not easy, it requires an experience and knowledge in this area in addition to physical strength. Conduct it without preparation can be a dangerous occupation - both for the driver and for the car.

The process of replacing the clutch from Ford Fusion It comes down to what is needed by being under the bottom of the car, disconnect the transmission from the engine. To perform this, you need to comply with the sequence of all actions, have a set required toolsIn addition, it is better to perform this procedure with a partner.

When replacing the clutch is better to produce replace all elements at once: Clutch disc, basket and frost bearing.

The main reasons for the breakdown of Ford Fusion

The list of causes of the clutch malfunction is quite large, we only give the most common of them.

• If the clutch ceased to turn on, it is possible that jumped clutch cable.
• Worn clutch discAs a rule, the clutch is also caused.
• Low efficient clutch work due to hitting oil-mud mass In the interval between the basket and the clutch disk, in this case it is enough to just clean the clutch without replacing it.

When to change the clutch from Ford Fusion?

This question directly depends on the style of driving: frequent gear shifts, the inexperience of the novice driver and other similar factors quickly wear the clutch resource, which leads to the need to repair Ford Fusion. Experienced driver, as a rule, calmly passes 100 thousand km On the factory set.

• during the work of the clutch, unusual noise, creak;
• when overclocking at low speeds (first, second) car no smoothness, it shakes;
• broken the smoothness of the pedal shutdown clutch.

When replacing the clutch and our Ford Car Service We will offer you to buy a suitable clutch kit for Ford Fusion from leading manufacturers at the lowest price. And qualified wizards will replace it promptly and efficiently.

In order not to bring to the extreme, we advise you to adhere to the manufacturer's recommendation and replace fuel filter Ford fusion every 20 thousand km, and for particularly caring owners who operate their cars in megalopolis, this period is recommended to cut up to 15 thousand km.

Ford fusion fuel filter is under the bottom in the back of the car, fixed on the bracket near fuel tank. For ease of replacement, it is better to use the lift or the lift, however, it is possible to carry out this replacement procedure and with the rear left wheels jack.

To replace the fuel filter follows only when the engine is turned off and the cooled. Moreover, before starting work it is necessary to reduce the pressure in fuel systemOtherwise, when disconnected fuel tubes From the fuel filter there will be a sharp release of fuel, which is extremely unsafe for the one who is engaged in the replacement of the filter.

Reduced pressure in the fuel system

To do this, remove the fuel pump fuse, then start the engine and wait a few minutes until the engine stalls. When this happens, it means that fuel residues have been produced from the part of the fuel line in which the filter is replaced.

Replacing Ford Filter Fusion Fusion

1. To begin with, nozzles are disconnected - input and reverse, clean the locations of their connections.
2. Then disconnect the old fuel filter and install the new fuel cell.
3. Connect the nozzles to your previous place.
4. When the engine is headed, check the connection points on the leakage.

A newbie can cause problems with the procedure to remove the filter from the socket. Here it is necessary to keep in mind that the latches on both sides have buttons located against each other. To dismantle the fuel filter, you need to click on them at the same time. Some owners conducting independent replacement of the fuel filter on Ford fusion and do not know this subtlety, forced to apply power to do what it is not recommended. In addition to the fact that the fastening can be brought, when using a sharp power in the system, the particle of sand can be dressed in the system, which will subsequently lead to clogging of the injector. And for washing the Ford injector, you will certainly have to contact the service center.

Where is it better to change the fuel filter?

Of course, it is better to do this by car service, and on the roadside garage, and in a specialized center, where Ford Fusion is regularly carried out. Here you will be offered a fuel filter on replacement, suitable for Ford Fusion.

In addition, self-replacement Car owners often choose an inappropriate or cheaper model of the fuel filter, which, unfortunately, often leads to Ford Fusion ignition.

The main task of the GUR is reduced to help the driver turn the steering wheel. In the absence of this system, the rotation of the steering wheel (and therefore the entire mechanism transmitting rotation from the steering wheel to the wheels) is a very difficult effect. After all, imagine you need, in fact, turn two wheels with bare hands tightly on the road and attached mass of the car. It is hard, especially if the car is in place. In motion, the rotation of the steering wheel without the hydraulic system is easier to make it easier, but still requires essential effort.

To facilitate the efforts of the driver Ford Fusion and invented GUR, which compensates for the driver's effort while turning the steering wheel.

The hydraulicer system is a closed system consisting of the following:

• tank with butter;
• pump for pumping this oil inside the system;
• a sensitive distributor that "decides" where the oil is further leaked to the hydraulic cylinder or back to the tank;
• the hydraulic cylinder, which, if the working fluid appears in it (that is, oils) transmits the pressure of the working fluid to the piston, which in turn through the lever system "helps" the driver turn the steering wheel in the desired side.

As soon as the car engine starts, pump GUR.Coming by the drive belt with the engine shaft starts the oil pump inside the closed system - from the tank to the distributor and back to the tank.

If the steering wheel is currently rotated, the system distributor is inactive, and the oil in the system simply circulates from the tank to the distributor and back to the tank.

If the driver performs the steering wheelThe distributor responds to this event and gives the command to open the access of the working fluid into the hydraulic cylinder. In turn, a pressure is created in the hydraulic cylinder corresponding to the power of the rotor of the driver, and through the lever system, the pressure in the hydraulic cylinder is transmitted to swivel fists; The wheels are rotated not only due to the driver's effort, but also due to the additional power generated by the pressure of the hydraulic cylinder.

What happens if the pump Gur Ford Fusion fails? When the engine started in the GUR system will not circulate working fluidSo, the system will not create working pressure. That is, when turning the steering wheel, the driver will work the sensitive distributor, the channels for supplying the oil into the hydraulic cylinder will open, but the oil itself will not be fed into the hydraulic cylinder (due to the lack of pressure in the system), which means there will also be no additional pressure on the wheels. In a word, with a broken pump of the hydraulic powerover, the driver when turning the steering wheel can only rely on its own strength.

In this case, the owner of Ford Fusion is necessary replace the pump gur, that is, to refer to the repair of Ford Fusion into a specialized car service. The Ford Fusion Hydrauscil Pump is located under the engine and, as previously noted, is associated with a belt with one of the engine shafts. Therefore, the replacement of the pump GUR in Ford Fusion is produced on the lift (on the overpass).

The question arises, is it possible to operate Ford fusion without replacing the broken pump GUR? In principle, you can, that is, the car will go. However, while the driver must have enough strength to turn the steering wheel. In addition, with long-term operation of the vehicle with off or faulty system Gur quickly wear out steering ReikaIt ultimately leads to the need to replace or repair the Ford steering rack.

In this case, takes place places in places fastening stabilizer Ford fusion. However, be careful, do not follow the self-diagnosis of Ford Fusion breakdowns. The knocks that are distributed from under the suspension may cause very other faults. You, as a driver, just need to contact the specialized center for repair Ford Fusion and report to the wizards about the observed knock.

The second option when for Ford fusion is required to replace the stabilizer rack - this is when it completely broke out. In this case, the safety of motion is clearly not reflected, that is, the car will continue to move and maintain stability on the road.

Here should be explained what role does the stabilizer stand performs The Ford Fusion car, however, like any other car. The main task of the stabilizer stand is to "stabilize" the car during turns, or rather to reduce the car roll during steep or moderate turn, and thereby keep the car stability on the road. This is especially true with steep, sharp turns at high speeds.

So, if the Ford Fusion Stabilizer is missing (and requires replacement), then when entering the turn on decent speedFirst, the car will be more stronger than the designers, which means the car can take a little, or rather, take out the road.

In practice, the driver does not notice this, because rarely who in everyday life chases at high speeds and is in turns so that already enters. Secondly, when there is a missing stabilizer rack when the obstacle is taken, or when the wheel hit in a hole, or when driving around Ughaba, the knocks are in front suspension, sometimes almost rumbled that the driver seems like " "(The piece of iron jumped into the engine crankcase), or as if in the glove compartment jumped the bunch of wrench keys. And when entering the twist, the knocks are heard.

If the retainer appears in the stabilizer, the stuffs can be heard when entering turns, when driving around irregularities. However, in this case, the knocks only annoy the Ford Fusion driver, but are not an indication for replacing the stabilizer rack.

The reason why Ford Fusion may have a stabilizer stand, pretty banal - she rusted and just broke into one "beautiful" day. In this case, you need to hold replacement Stand Stabilizer Ford Fusion.

Pretty simple and lies in the following:

• Drive the car to the overpass or raise on the jack.
• Remove the wheel.
• If the stabilizers did not change for a long time, we advise you to treat them with a miraculous lubricant WD-40 and wait for 10 minutes until the thread is soaked.
• Unscrew the bottom nut of the stabilizer rack first - there is a nut to use the second (stop) key to 17.
• Then unscrew the second, the upper nut.
• Remove the bar that holds the ABS wire.
• Remove the rack of the stabilizer from the place of attachment.
• Install a new rack and secure in reverse order.

As you can see, the replacement process of the Ford Fusion Stabilizer is pretty simple. However, we recommend to apply for this to the Ford car service.

Ford Fusion Engine Diagnostics

When diagnosing the Ford fusion engine is first carried out visual inspection All mechanisms, aggregates and engine connecting elements. Then carried out checking electrocontuterna Engine (candles, wiring). Finally, the onboard unit connects to a remote computer with a special fault testing program and a computer diagnostics of Ford is performed. According to the results of the analysis, specific problems are detected in the fuel supply system, problems in the electrician, in the ignition system and emissions of the exhaust gases, etc.

When diagnosing, it is checked by the service not only of individual elements of the engine, but its performance is also checked in the width.

This set of measures allows you to make a full-fledged picture of the damage in the engine Ford Fusion and make a plan for its repair. In general, the Ford Fusion Engine is a rather reliable unit, which cannot be fully said about the automatic transmission of this model.

DIAGNOSTICS OF ACP Ford Fusion

ACPP Ford Fusion is not the most reliable knot of this car. Even the drivers who hold a restrained driving style, on a certain mileage facing the battery breakdown. Read more possible reasons We have told the breakdown earlier in the article Repair Automobile Ford Focus 2.

As for Ford Fusion, then the diagnosis of automatic transmission conducted on special equipment In our service center, allows you to identify specific problems encountered in the gearbox mechanism. A breakdown of bearing and gear is often detected, friction discs or block of solenoids fail.

Diagnostics Chassis Ford Fusion

The car suspension is constantly subjected to colossal loads, so the wear of the car's chassis is inevitable. To avoid serious breakdowns and expensive repair of Ford, we advise regularly to diagnose the chassis Ford Fusion.

Our service center in terms of chassis offers two types of Ford Fusion diagnostics: visual plus tool inspection, as well as computer diagnostic Suspension. When combining both approaches, it is possible to determine the most accurately define a malfunction, as well as take into account the degree of wear. And, accordingly, pick up optimal option Repair Ford Fusion.

Repair by model - Text:

As well as services for comprehensive diagnostics and maintenance Ford Fusion providing our car service "Ford WAO". This car combines the permeability of the present SUV and the roomy of minivan, which is particularly valued by car owners with a large family, loving to travel to long distances. So, this representative of Ford, which appeared in the market in 2002, firmly won his niche in the Russian market.

Ford Fusion cars are equipped with both gasoline and diesel engines. Rule petrol Motors are represented by volumes 1.4 and 1.6 liters Power 80 and 100 hp Accordingly, A. diesel Develops power 69 hp These parameters are enough for car owners who acquire a car for family trips. As for the gearbox boxes, 4 or 5-speed options are offered to choose from MCPP or traditional 4-speed Automatic.

In general, the car is very comfortten: This applies not only to accommodation in the cabin, but also noted high level Comfort while driving. In general, the car is reliable, it has little weak placesBut still repair is sometimes required for Ford Fusion.

Despite the fact that the Ford Fusion car rarely requires repair, he still has vulnerable nodes.

One of the reasons to appeal to us car owners becomes failure steering rack. The reason can serve as the extended teeth of the screw mechanism on the steering shaft. When the helmet appears, the cause can be broken sleeves. In this case, the repair of the Ford Fusion steering rack will be required.

Another reason to conjugate with the repair of the Ford Fusion steering rack may be the failure of the pump hydraulic power steering. Often the cause of the breakage becomes the flow of the pump's glands, and if the reason in the breakage of the pump itself, you will have to replace the pump GUR Ford Fusion.

Transmission shift boxes, both machines and mechanics, extremely rarely require repair from Ford Fusion. However, the owners of the car with the manual transmission still have to be applied to replace the Ford Fusion clutch with a certain run.

Ford Fusion suspension In general, quite reliable. If there are breakdowns, most often they concern the replacement hub bear, replace the stabilizer rack, as well as replacing shock absorbers, both the front and rear. However, these problems equally relate to most other cars, not only Ford Fusion.

Engine and other systems, diagnostics of the running, steering system and ABS, checking the vehicle electrical system and much more depending on the cause of treatment. Diagnosis Ford Fusion. This is a big luck, because breakdowns identified at the stage of birth, easier and cheaper to eliminate.

Secondly, the diagnostics of the steering rack is carried out at the request of the client if the car owner indicates a clear failure in the operation of the steering system. Consider details some signs indicating damage to the steering rack.

Signs of fault of the steering rack Ford Fusion

This is a condition in which steering wheel It continues to rotate not some small angle with a stable (motionless) position of the wheels. In other words, you turn the steering wheel (there is a small angle of rotation), and the wheels are not rotated.

However, there is a minimally permissible lumber limit of the steering wheel, within which its functioning does not require the repair of the Ford Fusion Rajun.

If the permissible luminous limit of the steering wheel is exceeded, then the backup adjustment is required to the optimal value. This is achieved by adjusting the adjusting screws of the hinges located on the shaft of the steering wheel. If it does not help, then the teeth of the distributor rod and / or a worm pair teeth explode. In this case, they must be replaced.

Localized in the steering axis. (Note: A knock from under the front suspension may have different reasons for them. For example, a stabilizer rack has been replaced, the Ford Fusion Stabilizer Stabilizer is replaced. In any case, it is necessary to carry out a comprehensive Ford diagnostics). If we are talking about the steering system, the knock can be caused by the worm pair broken bushings that will need to be replaced.

The cause can be banal corrosion due to moisture in the steering system. To eliminate this breakdown, the assembly and elimination of corrosion are disassembled.

If you notice one or more signs listed above, then be sure to contact the specialized car service ford for the complete diagnostics of the steering system.