What oil to fill in Gur Ford Fusion. Independent replacement of liquid GUR on Ford Fusion What is the volume of oil in Gur Ford Fusion

The fresh car, the hardest requirements for operational fluids. The hydraulic power steering is also very sensitive to the brand of flooded oil. The amplifier works in complex criteria, under huge pressure in the system and often at high temperatures. In addition, in the design of the hydraulic agent, a mass of polymeric and rubber parts are used, which can be destroyed or rapidly wear out if the oil is selected incorrectly. Therefore, it is fundamentally to know which oil to fill in Gur Ford Focus 2, can I connect various brands And that Ford Motor Company is conceived about this.

As it does not matter, the other production fluid, the oil for the hydraulic agent is made or on mineral, or on synthetic, or on the semi-synthetic base. What is poured into the hydraulicer from the assembly stream, depending on the plant on which the car assembly was built. The color of water in this case will be the main beacon for the choice of oil for the topping and shift, but not the water producer. The company has established subsequent conformity for all water producers:

for reddish water - WSA-M2C-195-A ;

Apart from these liquids, yellow is also found. Usually, it is poured either poured at the factory in Vsevolozhsk. On the focus of the Cologne assembly, a reddish liquid is filled, and on cars collected in Spain - green. This is such a confusion.

Liquid for GUR serves for a long time, about two or three years, but after which it loses its characteristics and asks for shifts. The exception can only be damage to the pump or the amplifier hydraulic system. Then we will change on the fact of repair, and for the change we select the liquid recommended by a certain plant on which our specific Ford Focus was collected.

One of the ways to replace oil in gur

Read the same way

You can check the oil GUR using a syringe, pumping it out of the expansion tank.

If we do not know which fluid is flooded in expansion tank, Take a syringe, pump out a couple of drops and apply them to a snow-white napkin and set the color.

With all this, it is very fundamentally kept in the head that green oils do not mix with reddish and yellow, it is impossible to add them.

Reddish and yellow can be combined between themselves, but it is better to establish the composition of the water, since in the middle of the borders are found both synthetics and mineral water. Now on brands.

The most precious green oil for GUR - Fordovskoe (catalog number 1781003). It requires 1000-1200 rubles per liter in the boundaries. Green oil OT. FEBI brand G 002-000 C number 06162 stands within the boundaries of 360 rubles. There is a green analogue from SWAG with a number in the catalog 99-90-61-62. Costs about 400 rubles.

Easy way to get rid of noise gur

Read the same way

Ford EUROPE Reddish Liquid with Number 1776431 It is estimated at 2 200 rubles on average. Its analogs are larger and prices are softer. For example, South American Ford liquid for Gur Mercon LV XT-10-QLVC costs 550 to 800 rubles depending on the greed of the merchant. Marked as a transmission. Oil Ot Liqui Moly. ZentralHydraulik-Oil line - synthetic liquid and it has tolerances from Ford WSS-M2C204-A. Cost - 1200 rubles per liter. Similar properties in water LIQUI MOLY ATF 1100.

In principle, in the GUR second focus, there are all liquid of the same color as it was from the factory, but the presence of Ford tolerance to inspect certainly. Successful choice and bright roads! Ford Focus Fan Replacing Ford Focus Speed \u200b\u200bFocus His own TVIDEO "The car twisted during acceleration", "Ford Focus twitches when overclocking", "on small speeds the car twisted", "twitching Ford Focus 2" is so diligent The fact that my Ford focus twitches when ...

The fluids used in the hydraulicel can be divided into several criteria:

• Color;
• Structure;
• A variety.

Color classification

To be guided only by color gradation when choosing an oil is incorrectly, although this practice is widespread among the car owners. It is also often indicated which color of the fluid can be mixed, and which is not worth it.

The mixing is contraindicated with liquids in composition and not in color, and since now in any color can be represented as mineral water and synthetics, it should be treated with this information very carefully.

Red transmission aTF oilThe synthetic, reference is considered to be the Dexron brand from General Motors, but there are products of other manufacturers, such as Revenol, Motul, Shell, ZiC, etc.


The yellow, manufactured by the concern Daimler and on its license oil, is used in Mercedes-Benz hydraulic sensors. It happens synthetic and mineral.

Green oil. In most, multifunctional and universal fluids, according to the composition can be both synthetic and mineral. Used in hydraulic sensors, suspension and other systems involving fluids. It is impossible to mix with other colors, except when the manufacturer is declared complete compatibility, for example, COMMA PSF MVCHF is compatible with some kinds of dexron.

The composition of the liquid

According to the composition of the liquid, the GUR can be divided into mineral, semi-synthetic and synthetic. The chemical composition determines the basic set of oil functions:

• Viscous characteristics;
• Lubricating properties;
• Protection of parts from corrosion;
• Obstacle to foaming;
• Temperature and hydraulic properties.

Synthetic and mineral water can not be mixed with each other, since the types of additives in them have cardinal differences.

Synthetics

These are high-tech fluids, in the production of which uses the most advanced developments and additives. Oil fractions for synthetics are purified by hydrocracking. Polyesters, polyhydric alcohols and additive kits give them outstanding characteristics: a wide range of operating temperatures, steady oil film, long service life.


The main reason why it is impossible to pour hydraulic fluid on a synthetic basis in the GUR, intended for mineral - its aggressive effect on rubber products, which are a lot in the hydraulic fluoretide. Where synthetics are used, rubber has a completely different composition and is made on silicone basis.

Semi-synthetic

Mix of synthetic I. mineral oilsThus, the latter receive significant improvements in the characteristics: reduced foaming, fluidity, heat sink.


The semi-synthetic includes such well-known fluids as: ZiC ATF Dex 3, Comma PSF MVCHF, Motul Dexron III and others.

Mineralwood

Mineral-based oils contain oil fractions (85-98%), the rest falls on additives that improve the operating characteristics of the hydraulic fluid.

Used in hydraulovers containing seals and parts based on ordinary rubberSince the mineral component is neutral, and is not harmful to rubber products, in contrast to synthetics.


Mineral fluids for GUR are the most inexpensive, but also the service life is small. The Mobil ATF 320 Premium Mobil ATF 320 PREMIUM is considered a dexron oil to labeling inclusive.

Different types of oils

Dexron. - Separate class ATF liquids from General Motors, produced since 1968. The dexron is a trademark, produced both GM itself and other license firms.

ATF. (Automatic Transmission Fluid) - Oils for automatic transmissions, are often used by Japanese automakers and GUR.

PSF. (Power Steering Fluid) - literally translates as a hydraulic steering fluid.

Multi HF. - Special, universal fluids for GUR, having tolerances from most car manufacturers. For example, the SHF liquid produced by the German company Pentosin (Pentosine) received tolerances from BMW, Ford, Chrysler, GM, Porsche, Saab and Volvo, Dodge, Chrysler.

Is it possible to mix oils

Mixing is permissible, but it is necessary to be guided by the manufacturer's recommendations. Most often on the package it is indicated, with which brands and classes of oils can be mixed by one or another fluid for GUR.

Do not mix the synthetics and mineral water, as well as different colors, if there is no direct indication. If there is nowhere to go, and it is necessary to pour what is at hand, at the first other possible, replace this mixture to the recommended one.

Is it possible to fill the engine oil in gur

Motor - uniquely no, transmission - with reservations. Let us look in detail why.

To understand whether it is possible to pour out other oils, such as a motor or transmission, you need to know which functions it performs.


The fluid in the GUR must cope with the following tasks:

• Lubrication of all nodes of the hydraulic agent;
• Protection against corrosion and wear of parts;
• Pressure transmission;
• Obstacle to foaming;
• Cooling system.

The above characteristics are achieved by adding different additives, the presence and a combination of which and gives oil for GUR necessary qualities.

As you understand, the tasks of motor oil Some other things, so it is extremely recommended to pour it into the GUR.

About transmission Oil everything is not so unambiguously, the Japanese often use the same liquid ATF. for automatic transmission and hydraulovers. Europeans insist on the use of special PSF (Power Steering Fluid) oils.

What fluid pour in gur

Based on this, the answer to the question "What oil pouring in GUR" is obvious - the manufacturer recommended by the manufacturer. Often the information is indicated on the expansion tank or lid. If there is no technical documentation, call an authorized center and specify.

In any case, experiments with steering control are not allowed. Not only your safety, but those surrounding, depends on the health of the steering power steering.

How much oil in gur

As a rule, 1 liter of fluid is enough to replace in a passenger car. For trucks, this value can reach 4 liters. The volume may change slightly into a large or smaller side, but it is worth it for these numbers.

How to check the level

To control the level of fluid in the GUR, an expansion tank is provided. Typically, tags with the MIN and MAX value are applied. Depending on the brand of car, the inscriptions may vary, but the essence does not change - the oil level should be between these values.

How to attach

The process of the topping process is simple - you need to unscrew the lid of the expansion tank of the hydraulic plug and add so much fluid so that it is between MIN and MAX marks.

The main problem when taking oil in GUR is his choice. Well, if the replacement has not yet been done, and the system contains fluid from the manufacturer's plant. In this case, it is enough to refer to technical documentation, Take the recommended oil and add to the desired amount.

If you do not know what is flooded in the system, we recommend right away replace After all, in any case, you will have to buy a canister of fluid on a plot.

Everyone modern car Equipped with hydro (gur) or electric power steering (EUR). It simplified the management of the car and allowed the ladies to manage large cars, which is called "one hand". In turn, the steering power plants impose certain obligations on their owners, namely, the need to regularly monitor the state of the fluid GUR, as well as to produce its timely replacement after passing the car of a certain distance. Why did I not mention the EUR, because in contrast to the GUR, they almost Do not need maintenance, the effort produces a small motor that works from the mains and regularly performs its work regardless of the car's mileage. I will not delve into the details and argue that it is better or worse, instead, I propose to talk about more important - about how to replace the liquid in Gura to Ford Fusion At home.

The replacement of the liquid of the GUR on Ford Füzhn is not provided by the manufacturer, however, as practice shows, it is necessary to do this, the replacement has a positive effect on the operation of the hydraulic agent, and the control becomes more comfortable. Change the gur Before if a:

• Liquid darkened or changed color;
• The liquid appeared nasty smell burned;
• It is replaced by the details of the gur or hoses;
• You bought a car with big mileage And not sure whether "what" is filled into the tank Gur;
• The steering wheel turns hard, problems arise with control.

What to fill in gur FORD FUSION.?

What to choose for your car is to solve you, most importantly, that the oil corresponds to the requirements that are due to the manufacturer in the instruction manual for your Ford.

Before replacing the liquid GUR on Ford Fusion Prepare:

Independent replacement Liquid Gur on Ford Fusion - Step-by-step instruction

5. Now you need to lift crankcase protection, if any.

6. In the area of \u200b\u200bthe right wheel to the casing of the drive belts, the hose of the GUR loose hose on which it is necessary to find a "fast-consuming" fitting, which you need to remove.

7. After you disconnect the fitting, it is poured with both hoses old gur. Install the container and drain the workout.

8. After you need something, carefully shut down the hose hole, which goes to the tank, you can use the plug of suitable diameter or a piece of some rag.

9. With the second end of the hose, we do otherwise, it must be omitted into the container, since we will merge through it old liquid Gur.

10. Take it clean hydrauscitel liquid And fill up to the MAX mark.

11. We ask a partner to get behind the wheel and twisted the steering wheel left-right. Rotate the steering wheel is needed smoothly and without jerks - until it is right, then until it stops left. From such manipulations, the old oil will be squeezed out and merge into the prepared container, and the new oil that you poured into the tank will replace the old one. Your task is to keep track of which oil flows out of the hose and so that the Bach is constantly fluid of the GUR. Let's push the liquid until the hose flows the pure liquid of the GUR, that is, the one that you pour.

12. When a flirt of the liquid is fused, and a clean liquid flowed from the hose, connect the fitting with hoses and secure it back to the casing.

13. Get the engine and check how the steering wheel rotates, turn it as soon as possible then until it stops left.

14. Check the level of the hydraulic fluid level, if necessary, decrease the liquid to the MAX mark. After drowned out the motor and check the fluid level again if the level is higher than you need, pull out the surplus using the syringe, if the following is a fraction.

15. Further assembly is made in the reverse order.

I have everything replacing fluid GUR on Ford Fusion Implemented, I hope the article helped you and was useful for you. Thanks for your attention to the new meetings for Ford Master.

Today, almost every car is equipped with a system of hydraulic steering. With the help of the design, the steering wheel turns without much difficulty. In order for the mechanism to operate properly, a special mixture is necessary, which lubricates mechanical components and rubber parts, protecting them from friction and overheating. Lack of oil leads to excessive wear of technology. In order to avoid expensive repair, drivers must regularly monitor the amount of fluid in the GUR system and to replace it in a timely manner. How to do it yourself, consider on the example of replacement of the mixture of GUR in Ford Fusion vehicles.

Signs of the need to replace the liquid GUR on Ford

Hydraulic fluid B. cars Ford. Fusion is a technological oil with which resistance from the pump to the vehicle hydraulic cylinder is transmitted. Circulation of the substance occurs according to the binding nodes of the GUR system, as well as hoses. The required amount of the mixture is indicated by special MIN and MAX marks. Lack of oil requires its timely fill.

The GUR system itself is the main part of the steering. So the driver is enough to just unscrew the wheels and set the vehicle the necessary trajectory of movement. If the GUR fails to control the car, it will be much more complicated.

If when controlling the steering wheel, the steering wheel stopped turning - the liquid requires replacement urgently.

Signs of replacement of the mixture GUR:

1. When driving, the steering wheel is held greatly, and the driver feels the jacket;
2. During the rotation of the steering wheel, it is necessary to apply significant efforts;
3. Wheels are turning too easy;
4. Constant rejection of pulley;
5. The steering wheel is noise and publishes vibration;
6. The steering wheel is spoiled;
7. Parking driver can hardly.

The solution to these problems in most cases is timely replacement Oils in the hydraulicel.

Choosing a fleering fluid

The hydraulic fluid contains mineral and synthetic substances. The first most often used for passenger cars, such as Ford Fusion. Synthetic, in turn, used for special equipment.

Mineral oil performs the main functions of the GUR, protecting the mechanism from corrosion and excessive friction.

Manufacturers of the hydraulic mixture produce oil in three colors, depending on the type vehicle, as well as the specifics of the device gur system. It is not recommended to mix different liquids among themselves, since the composition of the mixture may be incompatible, as a result of which it will lead to a breakdown of mechanics.

Oil colors:

1. Red liquid GUR is designed for cars with automatic box Transmissions. It is possible to mix such a mixture only with yellow;
2. The yellow oil is neutral and most often acquired by drivers of any brands and TC types;
3. Green is designed for use exclusively in cars with manual box Transmissions. Such material does not interact with other oils.

Thus, it is necessary to acquire the oil according to the type of gearbox. The most preferred class - D III. Brands: Mobil 320 and Liqui Moly ATF 110.

To replace the hydrolytic fluid in the car of the Ford Fusion brand without pre-cleaning the system, no more than 1 liter will be required. With washing - 2-3 liters of solution.

Step-by-step instructions for changing the liquid in the power steering hydraulic

In the car you can make a complete or partial replacement Oil. The selection depends on the initial state of the fluid in the expansion tank. If the oil has acquired a characteristic, specific smell and color is recommended to completely drain, and then pour a new one.

The procedure for replacing fluid GUR in Ford Fusion:

1. Initially, it is necessary to drown out the engine of the car and give it to cool;
2. Open the hood and fix it;
3. Unscrew the lid of the expansion tank GUR;
4. Roll out all the liquid with a syringe and rubber tube;
5. To determine which hose oil goes into the expansion tank Gur is a reverse order, and what it goes and goes to the pump GUR;
6. Merge the remaining mixture in the system by disconnecting hoses;
7. Pour new liquid Up to maximum marks (1 l).

After that, the engine is not at the engine, you must scroll the steering wheel several times until you stop. So the mixture will be distributed across the entire system evenly. If necessary, after that, you can add oil.