We make a spoiler with your own hands. We make a spoiler with your own hands - step by step instructions Change of appearance

the main / Battery

For improvement external view The car market offers different elements of tuning, the spoiler belongs to such. Spoiler will make the car more attractive, it will give it positive side qualities. You can make such an accessory with your own hands, giving it the desired form. For independent work, expensive materials and special tools are not required.

What is a spoiler for a car

The spoiler is one or more special elements intended to change the aerodynamics of the body of the auto by redirecting air flow. The main objectives of the installation of this detail are as follows:

reduction of aerodynamic resistance;
an increase in the clamping force;
fighting the contamination of the car body.

It is worth mentioning that many install a spoiler as a decorative (tuning) element. Its fastening can be performed in front, behind, on the roof or side of the car. With an individual approach, you can make a spoiler to order, which will allow the serial machine to stand out in the transport stream.

The original spoiler from tuning atelier will highlight your car on urban streets.

Pros and cons Installation

Spoiler gives a car with the following qualities:

attractive appearance;
improving the speakers;
increased clutch with a web;
reduction of fuel consumption;
increased braking efficiency.

Need to clarify that positive traits The element under consideration is manifested at speeds over 100 km / h.

The disadvantages include:

high cost of structural elements;
increase fuel consumption with incorrectly selected form or installation;
fragile manufacturing material (plastic).

Options Tuning cars

Today you can choose a spoiler for almost any car, regardless of the type of body: from the sedan to the minibus. To make the choice it was easier, you need to figure out more detail, which criteria is classified this element tuning:

at the installation site;
by installation method;
by material;
in form.

The main place to install the spoiler is the back of the roof or the trunk lid. It depends on the type of body, as well as the size of the spoiler and its shape. Attach the element of tuning you can:

with the help of bilateral scotch. The option is appropriate with small spoiler sizes;
bolted fastening. This method does not like many motorists because of the need to make holes in the body;
fastening brackets. The option is suitable for those cars that have a certain form of the back cover and the gap between the body.

What material is suitable for tuning

As for the material for the manufacture of a spoiler, the most common are:

ARB plastic;
ordinary plastic;
fiberglass;
polyurethane;
aluminum.

To give preference to the design from a particular material, first it is necessary to consider each of them in detail taking into account its chemical and technical characteristics.

What form to choose

In the form of spoilers can be quite varied. To conclude that this option is suitable or not, the part must be seen in front of you. There are cases when the form of the element complements part of the body, but mostly spoilers are represented by the most non-standard structures. With their help, you can give a car not only exclusivity, but also aggressiveness.

Classify spoilers can also be design:

Rules for selecting a suitable spoiler

Today, a lot of spoilers are produced under the specific automobile Mark. Both model, but there are also universal options that are suitable for almost any car. The only difference is where they will be attached. In consideration, the car itself should be taken: if we are talking about a executive class, the spoiler clearly will be excessive elements in design.

It is important to evaluate how the selected accessory will look. To do this, it is enough to take the item, attach to the car and look from the side how much it comes to its appearance. Many tuning ateliers have a special program with which you can pick up optimal option, after which they are determined with the installation site of the element. If the spoiler is designed for a particular machine, then this question does not occur.

The spoiler is better to acquire without a paint layer, which will allow you to find the color corresponding to the car. An important point is the selection of a suitable fastening method.

In order not to make a mistake with the choice, it is better to apply only to proven firms on tuning. Only in such atelier can be installed really high-quality products.

When choosing a spoiler, attention should be paid to the material: in many cases, the part is made of plastic, for which both low cost and low service life are characteristic. Plastic spoiler under the influence of sun rays quickly burns out and breaks with minor blows.

In addition, there is such material as fiberglass. The detail made quite quickly loses its initial View And fails.

To better and, accordingly, expensive are products from carbon. It is important to understand that the high-quality spoiler should be manufactured under a specific brand and model of the machine, taking into account the improvement of its aerodynamic characteristics. Therefore, the universal versions can only be said that the level of their quality is questionable.

How to make a spoiler for the car do it yourself

When and why you have to ask the question of the independent manufacture of a spoiler? Today it is proposed big choice The element under consideration and, it would seem, do something with their own hands in this regard. But then the cost of high-quality spoilers is quite high, and this indicator is not a guarantee that the desired effect will be achieved.

Therefore, some car owners design spoilers on their own, getting the desired design and the desired effect from installing such an element. The homemade accessory can be made using the various materials that the owner chooses, based on its fantasy and free time.

Tools and materials

To start making a spoiler, you will need to prepare the following list of materials and tools:

foam sheet;
fiberglass about two meters;
fastenings and welding;
paint in the cans (2 pcs.);
primer (3 points);
epoxy glue 2 kg;
tassels;
spatulas;
reinforcement grid;
sandpaper.

Depending on the specific design of the product, the main material is:

gypsum;
styrofoam;
mounting foam;
metal carcass.

Stages of making homemade spoiler

The entire design process can be divided into several stages:

making form;
reinforcement of material;
putty;
painting;
installation.

As a pattern, it is best to use cardboard. You can use Phaneur, but this will lead to additional costs.

Regardless of the material selected, after the embodiment of the desired shape, be sure to include patterns by car. You need to make sure that the size is properly correct and the attachment points correspond to the locals. It is necessary to make sure in the symmetry of the future product, for which the milestone bend in half.

The frame can be made of different materials, but its main role is to keep the specified form at the beginning of the manufacture of the part. The rigidity of the spoiler will be found at the expense of fiberglass, as well as a layer of putty and paint. When choosing a filler, you need to consider the planned form of the future product.

Video: Production of tuning elements with their own hands

Production of foam and fiberglass spoiler

One of important stages The creation of a spoiler is the correct design. "On the eyes" this element will not be done. The ideal option at the design stage will be attracted to the work of an engineer or an experienced person who deals with this type of tuning.

After determining the sizes and design, you can start creating a metal frame.

Quite often, in the manufacture of the rear spoiler, a galvanized iron sheet is used with a thickness of 1.5 mm, the edges of which bend up. To the ground should also be awarded the M6 \u200b\u200bnuts for the subsequent installation of the product.
The resulting frame is placed on all sides by blanks from foam for increasing volume, the mounting foam is also often used. The thickness of the foam is chosen at the discretion of the owner. It is possible to cut it with a regular stationery knife or a metal blade. As a result, we get a matrix.
When the workpiece of the spoiler is ready, fiberglass (glass carbonate, fiberglass) is used to gave rigging. Three layers of material with small time intervals should be reached for the polymerization of the resin. Each subsequent layer should be more densely. It is necessary to strive to ensure that there are no air bubbles between the layers. The last layer of fiberglass must be coated with polyester resin. Optionally, a stop signal can be mounted in the spoiler, then the wires should be laid at the stage of fiberglass pasting.
To get good adhesion, the surface of the product should be primed, after which the putty is applied.
Subsequent actions are aimed at stripping the surface using sandpaper, it will give the spoiler as a smooth view as possible.
At the final stage, the part is ground and covered with several layers of paint, and then varnish.

Video: Audi A8 rear window tuning

Step-by-step manufacture of plaster spoiler

With the help of such a material, as plaster, you can make not only the matrix, but also a copy of the spoiler you like.

For the fill of the gypsum we make a box of foam. Then we lay the part matrices or the finished spoiler, after pre-wrapped it into the food film to avoid damage.
Pour the box with plaster. After the material freezes, we produce it cut into two parts. After selecting the original, we obtain an accurate copy of the form.
To make the workpiece, shape with a film and pour the gypsum.
After it is frozen, we reveal half the matrix and take out the workpiece.
Subsequent actions are aimed at finishing, reinforcement and painting of the spoiler.

To give a matrix of strength to adhere to the same recommendations that are given to the manufacture of a spoiler from foam.

How to make a spoiler from foam at home

The procedure is simple, but requires accuracy to avoid damage to the body cover.

We close with polyethylene the upper part of the trunk cover, you can also use greasy tape.
Mounting foam coating the prepared surface.
We expect the foam of foam, then a sharp knife form a future item.
In order to bring the product to the desired form, you should use sandpaper.
The rigidity of the product also attach the use of fiberglass.
The final stages are similar to the previous ways to manufacture an accessory.

The matrix can also be made of plasticine. The process is similar to the described sequence of actions for the manufacture of a spoiler from foam. Regardless of the selected way, you need to take care of sufficient rigidity of the structure. In addition, the fastening of such an element of tuning should exclude its loss, ensuring reliable fixation.

Video: Setting "Duck Tail" on VAZ 2109

Make a spoiler for its "iron horse" maybe each. To do this, it is enough to choose the necessary materials and tools. No matter what car is being subjected to tuning - "Niva Universal" or Mercedes Benz. Ml. If a scrupulously follow the step-by-step instructions, the car will be able to do much more attractive, and it is also noticeable to improve its technical characteristics.

The external tuning of the car is a kind of uniform, clothing, which is met by both the car and its owner, naturally. What parts belong to external tuning? All sorts of collaps, lining, chrome parts, anti-killers (they are spoilers). Everything, without exception, cars are held before making through the hands and eyes of designers who create one or another appearance, but often it happens that the lucky buyer and the owner of the car remains dissatisfied with this design, and then ... then the need for improvement and external improvement arises your car starts searching possible solutions. One of these solutions is becoming a sharp desire to buy a spoiler. However, it is not necessary to buy it at all. If you read the next general information about how to make spoiler do it yourself, it is quite possible that you will disappear obsessive the idea of \u200b\u200bbuying a shopping copy.

Options for materials and tools

There are several well-known ways to make a spoiler. Moreover, the craftsmen are used as the base for the shape of tin blanks, other gypsum fills, the third cut them out of wood or foam, and some particularly bold, can create a tuning masterpiece even from the ordinary newspaper. We will not take a specific example and dwell on it, because it is a matter of taste, skills, dimensions of your car and personal opportunities, but in any case you will need the next set of tools and materials:

pretty big piece of fiberglass;
reflective tape;
two or three paint cylinders;
approximately as many jars of primer;
approximately 3 kg of epoxy glue;
pieces five brushes for applying paint and glue;
two emery paper rolls (large, for giving shape and small, for grinding).

By the way, get ready to work well and painstaking hard, because for a day or two such work does not fulfill. In general, count on what spend at least two weeks, if you want a beautiful and neat spoiler.

Nuances of each material

Working with the gland, be careful and careful to the edges of the carved pattern, because the metal can be seriously damaged not only clothes, but also their own hands.
When used as a pattern of foam, consider its hardness and density. To process it, it can be consolidated both ordinary sandpaper, and a file or even a sharp stationery knife.
Gypsum forms are good because they are taken with almost any shape that you have conceived. But do not forget that the gypsum is heavy and very fragile material. From one wrong movement, it can not only split, but also turn into dust. In addition, still have to do some form where it needs to be poured. It is better to use the same foam or tree.
Well, the most masterpiece method is newspaper. To make the basis for a spoiler from such an unusual material, much mind will not need. It is enough to deploy a sheet, very tightly twist it into a tight tube, securing on the edges of the glue, so that it is not spinning, and then repeat these operations several times, laying the newspaper tubes one after another, depending on the size of the projected spoiler.

In principle, this is not a complete list of all sorts of materials suitable for the use and manufacture of spoiler. If the theory is understandable to you, then you can make the foundation from anything - at least from breadfall as criminals in prisons.

Finishing process

After the basis of the foundation, you must make the so-called "reinforcement". Simply put, taking a ready-made basis, it is necessary to give it a specific desired shape and clothe it into several (three-four) layers of fiberglass. Then the entire design must be impregnated with epoxy glue, give dry and frozen, and apply primer. After applying and drying the primer, the product is carefully (exactly thoroughly !!!) is polished by sandpaper so that the aerodynamics are perfect, and then it is painted and dried again. At the end, the reflector tape is glued to the feed part of the finished spoiler, although it is not necessary, and the spoiler is installed on the lid of the trunk, for example. Now your car will acquire a sports and rapid look, and you will meet you exactly ... Which you have done.

And for the sake of interest:

Before you take for work, it is worth learn what kinds of spoilers are and what the destination they have. This will help determine the manufacturer and speed up the result.

This article is intended for persons over 18 years

Have you already turned 18?

Spoiler do it yourself

Tuning or functionality?

When they talk about the tuning of the car, the spoiler or antiques represent most often. Anti-Cryl - additional detail Auto, which, thanks to the gap, increases the clamping force on large, above 80 km / h, speeds. It provides greater stability of the car and grip with a road surface. It is not entirely correct to call it a spoiler, but most motorists know it under this title.

Spoiler or, more precisely, Lip Spoiler - a detail of another destination and the clearance for this she does not need. Its task is to reduce air twists and reduce the coefficient of aerodynamic resistance. Usually it is fixed on the lid of the trunk, especially if there is a sharp transition from the horizontal surface to the vertical.

Anti-cycle and spoilers can be installed on a car in production initially or during operation by the car owner. The installed and manufactured independently usually carry the decorative function and their direct destination is not performed. With incorrect or incomplete installation of an anti-cycle, the car also loses in the technical characteristics, and in this case the spoiler has a negative effect on the car.

Anti-Cryl - Mandatory Element sports cars When driving on racing routes. In the car, the adjustable rear anti-cycle is installed, which is automatically activated by pressing the gas pedal by the pilot. This item significantly increases the speed on direct sections and helps on overtakers.

Anti-car - mandatory element of sports cars

In order for the antiques to cope with the task, it is installed not only on the back of the car, but also on the hood, and on the sides, the so-called body kit and the string expander, respectively. Otherwise, at high speed as a result of the work of the rear spoiler, the car will be lifted over the expensive front. The body kit in the car also performs the function of an additional cooler of the internal parts of the machine, thanks to the redirection of the air jet.

The disadvantages of anti-cycle can be attributed:

reducing road Suit auto;
worsening overview in the rear window;
considerable cost, if you buy ready and high-quality.

If you are going to buy a spoiler, pay attention to the material and manufacturer. Quality goods will not be cheap. Establish such a detail should be a professional master, it is better not to do this yourself.

The material for the manufacture of an anti-car can serve:

fiberglass is the most popular;
ABS plastic - light, plastic, with time becomes fragile;

Spoiler of the new sample of ABS plastic

silicone with silicone polymers;
carbon - excellent characteristics, but high price.

Spoilers can also be custom - these are design single specimens - and factory, which are produced by large parties. An anti-cycle body can be attached to bilateral scotch or self-pressing, if the design with racks. Depending on the design, steel or aluminum is used for racks.

Create a spoiler own

Many motorists are engaged in the manufacture of a spoiler for the trunk with their own hands. This saves substantially saves and in some cases it looks no worse than the expensive details of the tuning.

Before starting the manufacture of anti-splash, you should purchase materials and tools for work. You will need:

foam for the base, thickness 5 mm;
paint in the cans of the car;
metal sheet, thickness up to 1.5 mm;
epoxy adhesive;
carbon fiber.

We also need brushes, grinding paper and other little things.

Paint in the canister

Work on the creation of an anti-carbox is starting with cutting the base from the foam. Racks are made by their preferences made of metal sheet. Then the foam part should be glued to the racks and start layers to stick carbon fiber or fiberglass on the foam with epoxy glue. Before glueing a new layer, let's dry the previous one.

After drying the workpiece, the future spoiler is ground and align fine irregularities with putty. Then you should pass the blank of fine-grained emery paper, removing unobistant roughness.

We carry out the painting of the spoiler and after complete drying, we set it on the scheduled place of the car.

There is another way to make a spoiler with your own hands. The manufacturing technology is similar to the previous one. But it is not a foam, but gypsum. To do this, it is cut out of the foam you like the form, linse it with a film and poured with plaster. There should be two such parts, they glue them between themselves and begin to glue fiberglass. Next, the process is the same as in the previous method. This option, how to make a spoiler most time consuming, but also quite simple and affordable.

Making a spoiler for a car with your own hands

On the Internet, there is also a way of self-making based on mounting foam. Forces on it can be spent a lot, but the result is awesome. From the mounting foam on the car, pre-wrapped with a film, form the basis. Then cut the desired shape and grind. Then also use epoxy resin and fiberglass, but the top layer performs a putty, mixed with fiberglass and only then the usual one. The further process is similar to the rest: primer, grinding, painting, polishing. But as a result, a visor on rear glass With your own hands, it turns out indistinguishable from the factory and looks like a native detail of the car.

When manufacturing, it should be remembered that it doesn't matter how to make a spoiler on a VAZ or a foreign car, the main thing is that the result is worthy of attention and brings the owner aesthetic pleasure.

On motorcycles also set a related spoiler. Detail - fairing. Performs a protective function: motorcyclist from the oncoming wind and dashboard In case of accident. Thanks to various, sometimes completely unique designs, the bike outputs the total mass.

And there are ways to make a fair coaster on a motorcycle. According to the principle of manufacture, they do not differ from the above. The difference is enclosed only in the shape of the fairing and its layout.

Mounting foam spoiler

Some car owners before starting work on the creation of a spoiler with their own hands, drawn on the girlfriend - plywood, organity. It is easier to fit the size of the sizes by car. Online you can also find ready-made drawings of various modifications of anti-cycle.

Whatever your solution for the choice of anti-cycle, spoiler and fairing, always follow the first place what functions you expect from them. Setting the part only to improve the appearance without taking into account its capabilities can lead to unexpected results on the track.

Buy the factory spoiler or make it yourself - the decision takes the car owner based on its capabilities. But it is worth studying various photo and video materials on the Internet, manufacturers and other nuances. If you are not sure own power, remember that it is sometimes easier to buy than to spend time on self-making.

Now there are a considerable variety of all sorts of spoilers in the auto shop. However, often those who like externally are partially not suitable in size. Or perfectly sitting somewhat not reaching the characteristics.

What can make a car spoiler do it yourself?

If you encounter similar problems, then, of course, there is an option to buy a ready-made spoiler, and in the event of a shortage of length, simply cut the object and make an insert. Time costs are minimal, but here the cost of the spoiler itself is added to the cost of material and paint. And this turns out already enough.

Creating a spoiler from scratch is beneficial (expenses on average are about 25-35 dollars) and conveniently.
In order to independently make a spoiler to your liking and necessary requirements, we will need:

Styrofoam;
- epoxy adhesive;
- Sheet steel;
- fiberglass or old shirts "under silk";
- paint required color.

You can paint with a tassel or.

The process of creating a spoiler

Working with foam is quite simple, but there is one nuance. After cutting, a lot of garbage remains, which is very well electrified and can adhere to the drying element in the most responsible moments. So try to immediately remove the crumbs.

Polyfoam leaf size 1x1 and 4.5 cm thick (sellers usually declare 5 cm) cut diagonally. Cut the blade of the anti-car. So you just have enough width of the sheet of foam. Next, go to the attachments. It is necessary to cut out of the sheet steel plates 1.5 mm. Drills 3 mm holes with a distance of about 2-3 cm. In order to reduce the weight and improve gluing, bend them letter L. After these manipulations, we weld two nuts by 6 mm. Now you can incur them in foam blanks.

We glue the blade of the anti-epoxy glue with two layers of fabric. Then we collect the design.

We work on lip

The lip is done as well - not very difficult. Remove the bumper and turn over. Next, it is necessary to glue the blank from the foam. Give the shape and wrapping with polyethylene bags. Ideally, it is better to find the usual categorous female tights, stretch them on the shape and mold with epoxy glue. When the two layers of tights are dry, it is necessary to pull the blank from the lip. Packages are needed just so that the dweller calmly moved out, because epoxy glue does not stick to them. We leave the design for several days so that the epoxy is completely polymerized.

Then we take the fabric and give the lip again from the inside. In order to make the design even more durable, in the store building materials You can buy a reinforcement grid and sneak as well. Next, the design is grinding, ground and paint. After full paint drying.

Advice

1. Practice shows that the lip, made not from fiberglass, is quite vulnerable when hitting. Therefore, if you have the opportunity to purchase fiberglass, but better carboy, then the designs will be many times shockproof and more reliable.

2. Delete glue only with a tassel, it is convenient and safe, moreover, you can clearly calculate the amount of substance. The brush is wellhed in the solvent or in running hot water.

3. Do not prepare all the glue immediately, it is possible not to have time to spend it. SAMI most of Must be no more than 200 ml.

4. If you did not have time to remove the foam crumb on time, then try to touch the water tap in the kitchen more often, the electricity is removed.

5. If you use fiberglass, then for the reliability of the coolness of at least three of its layers. Usually, 4 layers of fiberglass, 2 layers of tights and a mesh are obtained on the spoiler. Each layer must be frozen, give resin to polymerize.

6. Want to speed up the polymerization process - increase the temperature.

7. If you take into account all these nuances and do not hurry with the assembly of the lip and spoiler, then the conceived can safely get the first time.

VAZ 2106 is one of the legendary cars of the Soviet car industry. He won the love of many domestic motorists and is very popular so far. Paradox is that this model does not differ any special characteristics or appearance. It cannot boast and the comfort of stay in it passengers.

This is what is really present in it - this is humility to its owner and readiness to fully adapt even to the most unexpected desires. With the "six" you can do anything right in my garage. In this article we will discuss the topic "Tuning VAZ 2106". Consider three refills:

change of appearance;
improving technical characteristics
enhance comfort for passengers.

Many stop only on what is performed by classic beard tuning, headlights and put casting. But you can find a lot of ways to improve your car. We will not fully consider all possible types of modifications. We affect only the most common and affordable ways.

Change of appearance

Painting body

This is a type of tuning that instantly completely transform your car. Especially spectacular looks painting VAZ 2106 in a pearl color. You can pick up the similar shades. Only this procedure can turn your old man in the new-fashioned handsome man!

In addition to painting, the body is decorated with numerous stickers. Pictures on the body give the appearance of the car a fashionable retronotka and a special style. But this kind of "decorations" in the soul is not everyone.

Lights

This is the eye of the car. If you want to give a beautiful look of your six, without modifying it is not necessary. Tuning headlights on the VAZ 2106 - the main element external tuning. Often, the headlights are remembered in the design of the car in the first place. Not in vain company BMW. Pays them so much attention. And although to the BMW of our favorite six as to China, you can still significantly improve this design element.

If you want to change something with minimal investments of money and time, you can do cheap overlays and reflectors. Ordinary light bulbs are replaced by halogen. There are many color shades for light on the market.

If money and time are still available, then you can put advanced headlights. To do this, you will have to finalize the body's configuration and make changes to the fixture system.

Radiator grille

Another spectacular way to transform the "face" of your car is a tuning of the grille of the radiator VAZ 2106. With it, it is possible to give a character. Your six can become cute and beautiful, and can purchase brutal courageous features. There are many different models with changed shapes and colors on the market.

Alloy wheels

For the car VAZ 2106 tuning with their own hands to make it very easy. Sometimes enough just to put alloy wheelsTo completely transform the appearance of the classics. It makes no sense to make big changes to the appearance of the car if classic iron discs are standing on it. With casting, you can give more style and improve dynamic characteristics. Casting is lighter than iron, so the wheel load decreases on the suspension. Such discs are faster. Thanks to the embedded ventilation holes, it is possible to cool the elements. brake system.

If using low profile rubber, You can put discs with a large diameter. This will improve the maneuverable characteristics of the Zhiguli. In addition to casting, there are also forged and alloy models.

Muffler

The standard option is easy to replace on a straight-flow silencer having two discharge pipes with a beautiful chrome design. It would seem a trifle. But it is precisely in detail and buried the real beauty! Moreover, one only this modification increases the engine power by 15 percent. And the noise of the exhaust system will be significantly reduced.

Boots (skirts, bumper VAZ 2106, spoilers)

Native bumpers and other sides look at the sixth. If you put a five-packet bumper on the VAZ 2106, tuning will be cheap. It looks much more nice. Yes, and the traffic police will not arise.

But if you want to give a car bold racing look, you will have to fork out on a more expensive tuning of the Bumper VAZ 2106: Buy sport models. But remember that the inspection may have problems.

Hood

On the standard hood of VAZ 2106 cost two holes that are designed to supply air to the stove fan. In stores you can find different types Registration of air intakes for 2106. The tuning of the hood with this design element will make it possible to make a complete completion in the design of your six.

Spoilers

The main purpose of the spoiler is to change the direction of the air flow by making the car more stable at high speed. Thanks to the operation of the spoiler, the car presses to the road, which enhances friction, which means improves the dynamic characteristics. But most owners of the VAZ 2106 love this product for another reason - it looks very beautiful.

There are hundreds of different modifications that have different shape and manufacturing material. The most beautiful and durable are made of aluminum. Cheapest - from plastic. Rear spoilers received the greatest distribution. But there are other models intended for installation in front and side.

Improving technical characteristics

Motor

By car VAZ 2106 improve the work of the engine is easy and not very expensive. It is only necessary to buy some parts and install them instead of full-time elements. Such a tuning of VAZ 2106 will allow not only to increase the power of the motor, but also to extend the service life. What can be put?

Lighter valves, with what revolutions increase.
Together with the valves put their bronze guides.
Carter gases filter. It is not worth a full-time version, but plays an important role. Thanks to his work in the carburetor falls much less oil And did not climb it.
Turbine. It allows you to increase the speed limit of the six. Together with her it will be necessary to put special pistons with turbo marking.
Collectors. They not only help increase Efficiency of work Motor, but also create a special sound of a motor, similar to the roar of the supercar.
Carter that additionally protects the engine.

Tuning carburetor

The device of this item is quite simple, so it can be easily used to improve the technical characteristics of the Zhiguli. There are three classic methods to perform tuning carburetor:

On the throttle valve Spring is removed. This allows you to significantly increase engine power. However, this slightly increases fuel consumption.
Diffuser in the standard equipment has the designation 3.5. It is necessary to replace it with the one that has a marking of 4.5. And instead of the sprayer, a similar part is installed on 30.
Controversial option: Increase the jets. Although it gives a good power increase, but very much increases consumption.

Suspension

If you modify the engine and carburetor, it is necessary to carry out the appropriate work with the suspension. Otherwise, it will not withstand increased load.

Shock absorbers change. Instead of standard, more rigid with two sections or sports are installed. You can still put shortened modifications. Many love to "undress" VAZ 2106 in this way.
Change diameters. This makes it possible to improve maneuverability at high speed.
Factory hinges change to tuning steel spherical. This not only makes the design more reliable, but also improves comfort while driving.
Sports are put brake discs. The rear brakes change to modern modifications. As for the brake system, it will not hurt to install a large cylinder.
In order for the car to receive improved patency, the differential lock is set.

All these works with the six are easily held in the garage with a pit or on the lift on their own.

Clutch

After the works on tuning the technical part, it is very important to check the work of the clutch. The pedal move should not exceed 130 millimeters. It will be best to put a new slave disk.

Transmission

If you have finance, you can put a sports transmission, which is different from standard gear ratios. These numbers are selected depending on what driven driving manner. The transmissions will switch much faster if you put a short coolers.

Comfort inside the cabin

Everyone wants to get the maximum comfort in the car. However, everyone does not have money for the purchase of expensive elite cars. However, and the old Good Six can be transformed beyond recognition and give it the features of superdowed BMW or Mercedes. Of course, it will fall out in the "penter", but it will be much cheaper to cost than the acquisition of models of these brands.

For VAZ 2106, the tuning of the cabin is carried out by the following methods:

Upgrade dashboard

Tuning panels can be carried out as you like. You can draw a slight tuning of instruments on the VAZ 2106. For example, change the backlight of the instruments. You can put new more beautiful appliances. You can stick leather inserts to certain places. And you can simply put a beautiful instrument panel with a sporty view specifically designed for the "six". Beard tuning is an extensive field for a rich imagination.

Power windows

Installation electrical system Lifting glass is a simple and cheap way to carry out tuning doors. Replace regular "twisters" can be easily both on the front and on the rear glasses.

Warming windshield

A very useful feature that will enjoy the inhabitants of cold regions. It is important to work correctly, since incorrect heating can lead to a burst lobby glass On the frost.

EUR or GUR.

Any driver of "classics" will be extremely glad to feel how simpler it became possible to drive a car thanks to installed system Electric or hydraulic power steering.

Heat

Improved stove model with aluminum radiator, air ducts on rear seats And good thermal insulation will allow passengers even in the coldest winter easily to transfer a long path along the track. This is the necessary element of the comfort, which each VAZ 2106 owner must take care of.

Noise insulation

Zhiguli was never famous for good insulation. At the same time, you can install Shumkov on your own right in the garage. It will be true to spend a day or two with a small experience in this area. However, the result will exceed all expectations. It is best to take good materials at once. Therefore, a slight decrease in noise level is unlikely to please you.

Audio

Good music is one of the main components of the comfort while the way. Noise isolation itself will significantly increase the sound quality on the track. However, good acoustics throughout the salon and a powerful subwoofer will fully transform your impressions from riding around the city and will cause a strong feeling of envy of most cheap foreign cars.

Seat replacement

Statery seats will have to change. It is not even discussed. They are neither not adapted to move in a car longer than 20 minutes. You can easily change them on those that stand in Ford Scorpio.. These are much more comfortable seats that are ideal instead of regular. We will have to tinker with fixation of the design. But a couple of hours of operation is not too high the price for a healthy and well-rested back and comfort in long distances.

Salon and seats

You can significantly change the nature of your car, simply pose the most suitable for you to cover its interior. There are many options. You can choose the most interesting color for you and the material manufacturing material, which will create the most individual personalized design inside the salon VAZ 2106.

Illuminated salon

Via lED backlight You not only add beauty to your salon, but also make the planting process and disembarking passengers more comfortable and safe. After all, in the dark, the thresholds and ceiling of the car are so nice.

Armrest

Very important element of comfort for both the driver and for rear passengers. Today there are plenty of solutions for the VAZ 2106, which will allow you to organize a convenient driver's armrest with a built-in glove compartment with several departments and even a cup holder. And for the rear passengers, you can embed the middle armrest in the form of a table with cup holders and a department for things. And in order not to lose the third passenger placeThis armrest must be folded into the back of the seat.

Toning

Legislation in our country allows us to tint rear window and rear side glass. This needs to be used. After all, toning will not only allow passengers to escape from the eyes of people in the city, but also protect them from the scorching sun.

Air conditioning

Modern motorists cannot imagine life without air conditioning. What you can not say about the "happy" owners of the classics. However, today there are many solutions that allow you to put Conder even on the old six. There would be a desire and money.

Luke in the ceiling

This is an indispensable attribute of all luxurious elite car models. But who said you are not worthy to have a similar chip in your zhiguli? If there is a finance and familiar specialist, then you can put a large glass hatch to the roof of the six, which will allow you to breathe fresh air on a hot summer day and admire the stars at night.

You can list many more different ways To carry out tuning VAZ 2106. But we think that even all these methods will allow you for a relatively "modest" amount to become the owner of a modern dynamic car with a luxurious appearance and a comfortable interior.