How to replace the oil in the CHEVROLET ORLANDO automatic transmission box. Independent oil change in Chevrolet Cruze automatic transmission where the probe checking oil on Chevrolet boxes

the main / Driving

Some car manufacturers say oil in automatic box Calculated for the entire service life, and it is not necessary to change it. But it is not. On large runs, the details wear out, technical fluid And the filter elements are clogged with a metal chips. Because of this, the lubricant deteriorates, and the details wear out even more.

Check level

Checking the oil level in Chevrolet Cruz automatic transmission is a rather complicated event, it will be needed for it. looking Yama and tools. But without it it is impossible to know how much fluid is missing and what is the reason for the shortage. Periodically, you need to inspect the bottom of the car to make sure there are no leaks of technical fluids.

First, warm the car to see the objective level. As is known, the cold liquid is compressed and does not give an objective picture. Do not jerk motor, rearrange the gear knob in different modes. It is necessary for lubricating all the details.

Stay at the observation pit and on the engine installed, put the gearbox to the "P" position. Take the horn key to 11 and find the control plug on the gearbox. It is located at the exit of the checkpoint, on the back of the mechanism, from the end.

Take the clean capacity, put it under the cork. Carefully unscrew it. If the fluid flows the thin flowing, it means that the level is normal. If nothing flows, then the amount is insufficient. You need to watch the video to understand how to add oil into Chevrolet Cruz automatic transmission. This is done under the hood through the Sapun. You need to pour until it goes through the drain hole.

If the level was sufficient, all the outlined oil from the Chevrolet Cruz automatic transmission must be pouring back after you tighten the cork. It is recommended to keep an increased 0.5 liter level.

How often do you need to change the oil

During the topping, you need to check the color of the liquid. Dark, rich black color says that the replacement is needed. If the oil has become muddy, it is recommended to change it. If these signs have discovered after a recent replacement, it speaks of a breakdown in the mechanism.

The replacement time depends on the operating conditions of the car. If you often go high speed or move soil roadsThe interval can be reduced to 60 thousand km. Remember that at speeds above 150 km / h, the box is heated to 120 degrees, at such a temperature lubrication loses its properties.

The process of partial replacement

The first thing you need to replace the oil into Chevrolet Cruz automatic transmission is the observation pit. Before working, driving a car, passing 5-10 km. Put the machine in the garage or on the street pit. In winter, it is recommended to carry out work in the warm room.

Required tools:

a set of keys;
capacity;
clean rags;
funnel;
new liquid.

Capacity should be quite large, as 5-6 liters of fluid will fall. It is best to work in gloves so that the technical fluid does not hit the skin. It is better to wear workwear on the body, which is not sorry.

How to change the oil into Chevrolet Cruz automatic transmission:

Check the temperature sensor transmission fluid. Check the box while driving, all transmissions should be switched on smoothly. Do not forget to mark the date of replacement of the oil in the CHEVROLET CRUZE automatic transmission, so as not to forget.

pros partial replacement:

All work can be carried out independently;
The old oil is mixed with the new, the composition is updated;
Less risk to break the box operation;
Small oil consumption.

The minus is that it will not work out completely update anyway, even if you do it several times. But with the help of such a way, you will save on the liquid and on the work of the masters.

Full replacement in the service

You will not be able to fully update the oil yourself, as it requires special skills and equipment. With the help of a special device for a hundred, new oil is pushing the old and 100% update occurs.

A tube of the device connects through the box radiator, the engine starts. At the same time there is a plum old liquid And the fill is new. The master through a special window controls color. As soon as the shade of oil becomes normal, the procedure is completed. The cost of work is not very high - from 1000 rubles, depending on the city.

Benefits of the method:

You control the whole process and see how the Color of ATP is changing;
The flow rate of gasoline is reduced after replacement, since the power loss in the hydrotransformer decrease;
Switching becomes more smooth, the automatic transmission reacts better to driving style;
Professionalism of masters eliminates the possibility of error.

But the full replacement has its drawbacks:

Automaster can provide a guarantee for its work, but will not give a guarantee for smooth operation of the box;
On car S. big mileage The device can wash useful deposits from the mechanism, which will lead to breakdowns;
Not in each service there is a necessary device;
The cost of the service is higher than for partial replacement.

How to choose oil and filter

Important! To fully update the oil in the CHEVROLET CRUZE automatic transmission, you will need 7.5 liters of fluid. If you merge it only from the pallet, then you need to buy 5.5 liters.

At the plant in Chevrolet Cruz poured Dextron GM VI. You can choose another manufacturer if replacing the oil completely. For topping it is better to buy that liquid that is already flooded.

Pay attention to the label on the packaging. Be sure to be present inscriptions:

Class VI.

If you do not know which oil in Chevrolet Cruz automatic transmission, choose from official manufacturers:

Mobil;
Havolin;
Chevron.

These brands are poured into GM canisters, so you can take any. If you have one of the listed brands in the motor, you can pour the same into the box.

Interesting fact! In the hydraulicer poured the same liquid, as in transmission.

You also need a filter that will clean the liquid from harmful impurities. It needs to be changed every 80 thousand km, you can do it without an oil update. But the most convenient to combine these actions. To the filter in automatic transmission free access, you will not need special tools.

If you do not know what oil to fill in Chevrolet Cruz automatic transmission, read the reviews of motorists and choose a suitable brand. Focus on your feelings from different brands. If you partially update the fluid, make a second replacement after 1-2 thousand km.

Cars " Chevrolet Aveo.»Evoid popular in Russia and abroad. It is inexpensive but practical car With decent technical characteristics. If you chose yourself a version with an automatic box, you should know about the nuances of operation of automatic transmission, checking the level of lubricating fluid and the features of its replacement as needed. in automatic transmission in " Chevrolet Aveo. T300 "takes a little time, but requires mandatory compliance with certain rules and recommendations. The main of them are the frequency of replacement and proper selection New lubricating fluid.

Before replacing the oil in the CHEVROLET AVEO automatic transmission, check the level of the old one.

Replacement frequency

Engine oil, like oil in the gearbox, has its own suitability. This period of time during which the lubricating liquid retains its operational and physico-chemical properties. Typically, the engine oil varies several times more often than the transmission. This is due to the rigidity of the conditions in which oils are located and the intensity of their work. If we talk about when it is necessary to change the oil into the car "Chevrolet Aveo" car, then you need to look into the instruction manual. The automaker advises and updates to the transmission lubricating fluid every 60 thousand kilometers passed.

But in reality it can happen somewhat more often. The more intense you operate the car, the faster the oil in the gearbox is wearing. Heavy conditions require more thorough control of the state of fluid and reducing the period between replacement. Therefore, some car owners have to merge and pour oil into automatic transmission every 30 - 40 thousand kilometers.

Select Oil

To purchase a new oil for the gearbox of its "Chevrolet Aveo", use the official instruction manual for the machine. It indicates that the T300 uses engine oil with technical characteristics denoted as Dexron VI. This is optimal in its technical and physicochemical properties. transmission oilsuitable for automatic transmissions. Oils with appropriate characteristics and labeling are issued by different companies. Therefore, repel from the designations on the containers. Among the most preferred manufacturers are distinguished by such:

Petro Canada;
S-Oil;
Havoline;
Conocophillips;
EXXON MOBILE;
Kendall;
Chevron;
Petronas;
Sinopec.

Each of the submitted oils with the corresponding characteristics is suitable for Chevrolet Aveo cars on which the automatic box is installed. Use only high quality oilhaving all certificates and authentication. The market meets and fakes capable of harvesting the automatic box.

Preparatory activities

To change the oil in the gearbox successfully, and you correctly performed work with your own hands, preparation is required and a set of some tools. For "Chevrolet Aveo" with automatic transmission when changing the lubricating liquid you need to take:

set of tools;
multiple keys and heads;
empty tank for old transmission oil;
metal brush;
new gasket for the pallet;
new oil filter;
degrees;
dry rag;
new transmission fluid;
special neck for fill oil.

This is a standard set of tools and materials that will be useful during the replacement of transmission oil on Aveo.

Verification of state

To estimate the current state of the transmission fluid, you need to check how much oil in the box "Aveo" is at the moment. Rate the existing volume in the checkpoint, the level and look at the fluid itself. It is easy to understand. To do this, under the hood is a special probe automatic transmission. It is used in the same way as probe motor oil. Therefore, keep dry rags at hand and focus on "Min" and "Max" marks on the Long Property PPC "Chevrolet Aveo".

If the probe showed a deviation from a normal level, do not rush to simply add a little fresh oil. Take a white cloth and drop into it a few drops of liquid. If it differs in color from fresh oil, it has interspersed or particles of garbage, dirt or metal dust, this indicates its wear and contamination. Better fully. Previously, it will be necessary to know, because of which the oil in the "Chevrolet Aveo" automatic transmission produced ahead of time, there is no leakage or any breakdown in the automatic box.

Replacement

If the check showed that the transmission oil needs to be changed, proceed to work. It can be done with your own hands, saving enough money for car services. Plus, practice shows that not all the hundred people are capable of better than the car owner will do it independently.

Follow the instructions to do not have extra questions and difficulties during the procedure:

For a start, the protective part of the pallet is dismantled, if such is provided on your "Chevrolet Aveo". Protection is held on three bolts, which could take it during operation of the car. If they are not amenable to a simple force from the key, use the WD40 and wait until the transmitter works. Now the bolts must succumb to. Additionally, it is recommended to remove the stretching from the subframe, because otherwise there will be difficulties during the dismantling of the automatic transmission.
Take advantage of a rough metal brush to clean the surface of the pallet and the speaker itself, which opens the path to the transmission fluid plum.
Before unscrew the plug, substitute an empty container for 3-4 liters under it. If you plan to pour existing oil back, then use the clean tolement. Exhaust oil can be merged into dirty containers, since it is still disposed of it.
By reloading the plug hole, wait until the entire transmission fluid follows. This will require some time. The back of the car can be slightly lined with a jack, which will allow the oil somewhat faster to flow. Also, the process will accelerate and remove the bay hole located under the hood.
When all the grease from the AVEO automatic transmission came out, return the plug into place. And along the edges of the pallet, find the fastening bolts. They need to be unscrewed. If you are bought, use the WD40 again.
Now dismount the pallet and get rid of oil residues that are on it.
Be sure to remove the gasket. Take advantage of cleaners to thoroughly rinse all components, magnets and pallet. The rubber sealer is better to immediately change to the new one. Orange gasoline is suitable as cleaning fluids, or you can use special compositions From automobile chemistry stores.
Unscrew the bolts that hold the oil filter automatic. Standardly on "Chevrolet Aveo" are used 3 pieces. This will make it possible to remove the filter element without any problems.
Rate the current filter state. If the automatic transmission is operated for a long time and the transmission oil has not changed before, then the filter will be strongly contaminated. Trying to wash it does not make sense. Better buy new. Put it into place of the old transmission oil filtering device.
On the purified pallet, put magnets according to the location of their original location. Next, a new sealing gasket is installed.
The clamping part of the automatic transmission is treated with degreasers and purge. This allows you to now return all the details into place.
Next, you can proceed to replacing the oil into the mechanical automatic transmission "Chevrolet Aveo". To do this, go to the incaparment and look for a hole where the probe is inserted to check the level of transmission lubrication.
Make sure the drain hole is closed. Taking advantage of the filler neck, start gradually pouring fresh oil into the box.
For "Chevrolet Aveo", the volume of lubricating fluid in an automatic transmission is about 3 liters. We make the error on the remaining oil in the system. Minimum, you should purchase 4 - 5 liters of suitable transmission oil. First fill 2 liters.
Sit into the car and switch the ACP lever into different positions alternately, but you do not need to start the engine. After that, 1 liter of lubrication will be logged in the system.
Bay all the required amount of oil, run the motor. Set the automatic box to the parking position and check when the power unit is running, which is now level.
Until the motor works, switch transfers with small gaps. Finish manipulations on the position of R.
It remains thoroughly warm up the motor to operating temperatures. If you see insufficient level Lubricating fluid, drop some more oil.
When the level has reached the desired marks, look under the bottom of the machine and make sure that there are no leaks. Carter protection and stretching can be installed on their legal places.

Although the procedure for replacing oils in the automatic transmission to "Chevrolet Aveo" has its own characteristics, there is nothing difficult in it. Therefore, most car owners prefer to do work with their own hands. Here, the main thing is to follow the instructions, comply with the safety rules and choose the oil that meets the requirements of the automatic transmission of your Chevrolet Aveo.

Thank you all for your attention! Subscribe, leave comments, ask questions and do not forget to invite your friends to us!

Many Cruz owners are repeatedly wondering how to check the oil level in the automatic box. Immediately, I would like to note that the inspection of the automatic transmission does not have, so the oil level is measured using a control plug.

Procedure for Checking Oil Level Box Machine Chevrolet Cruise

Before checking, the box should be warm. It is better that the warming process takes place in the car movement, in this case the coupling and the valve block will be filled with oil.
After stopping on switching the gear selector over the entire range, and make a delay of 5-10 seconds on each position.
Then, not the gentle engine, with the help of the key to 11, unscrew the control plug. In a pre-prepared capacity, we give stroke oil.

If the oil, after turning the plug, did not flow, therefore, we have a low level and its topping is required. It is recommended to maintain increased oil level in Chevrolet Cruz On average, 500 grams are more.
The oil is rolled into the automatic box through the Sapun, which is located on top of its housing until it flows through the control hole. This is if the oil change in the automatic transmission is not required.

Then we twist the cork and felt approximately 500 grams.

During inspection oil levels Chevrolet Cruz Pay attention to its color. If the oil has a dark shade or completely black, therefore there is a breakdown that must be diagnosed and eliminated. After what to produce full replacement Chevrolet Cruz Oil Boxes.

Automatic gearbox is one of the main energy transmission nodes between the power installation and wheels. It is very sensitive to the quality of lubrication and observance of replacement intervals.

During operation, it is required to periodically monitor the oil level and, if necessary, add it. In cases of violation of these rules, an automatic transmission failure is possible, after which expensive repair will follow.

Selection of oil for automatic transmission on Chevrolet Cruz

Three types of automatic variable transmissions are installed on the Chevrolet Car Cruise:

6T30;
6T40;

No matter what machine goes in chevrolet configuration Cruze, General Motors pours to all automatic transmission oil GM Dexron VI. Article of the original lubricant - 93744589. Official dealers recommend using only original motor and transmission oil.

There is also analogue original oil from GENERAL MOTORS. This lubricant is Opel ATF DEXRON VI. This liquid is as similar to its performance characteristics And the package of additives with native oil Chevrolet Cruz. Article number transmission opel fluids - 1940184. The price of it is slightly lower than the cost of the original and is 450 - 500 rubles per liter.

According to the Manual in Chevrolet Box Cruise with an engine at 1.4, 1.6, and 1.8 liters, you can pour a transmission oil that complies with the DEXRON VI standard. Lubrication of third-party manufacturers has a value smaller than the original, while the quality of many brands are at a fairly high level.

Good budget oil is Petro-Canada Dexron VI. It retains its initial properties from replacement to replace. The transmission fluid in the canisters is faced, the volume of which is 1 or 4 liters.

According to the reviews of experienced car owners, one of the best analogues of the original oil is Liqui Moly. ATF Top TEC 1200, the article 7502. After its fill, the machine works evenly, and the friction surfaces are reliably protected from wear and appearance of scaling. Oil also has good anti-corrosion properties.

Mobil has good features ATF Dexron. Vi. Its articial number 071924252233. In oil contains powerful detergent additives.

Checking the oil level in the gearbox on Chevrolet Cruz

Monitoring the number of transmission oil in Chevrolet Cruz gearbox has one important feature. It is connected with the fact that the automatic transmission that the car is completed, have distinctive design solutions. Chevrolet Cruze 2009 - 2012 releases have a measuring probe. In the rest of cars there is only a control opening.

In order to control the lubricant in the automatic transmission, you must follow the instructions below.

Warm force aggregate and transmission. To do this, you need to drive a few kilometers.
Close Sapun in the gearbox.
Press the brake pedal and start the engine.
Translate the ACP selector to D.
Wait 10 seconds.
With the same interval several times across all the modes of the ACAP selector.
Stop the lever to the parking or neutral position.
Unscrew the control plug. If the oil level reaches the edge and a little lubricant ran out through the hole, the number of transmission fluid is normal. In the case of automatic transmission with a measuring probe, the amount of oil should achieve its maximum mark.

Filling volumes and interval of replacement

How much fresh transmission fluid is needed depends on the version of its shift, which will select the car owner. It is possible both complete and partial replacement. More detailed required oil volume is discussed in the table below.

According to recommendations official dealers The replacement of transmission fluid must be carried out every 75 thousand km. Since automatic transmission is sensitive to lubricant state, it is desirable to reduce the replacement interval to 40-60 thousand km. It is especially important for machines operated in urban traffic jams, or when driving a driver driving.

Required tools

To replace the transmission fluid, the car owner need a set of tools and materials that are shown in the table below.

In case of replacement of oil with removal of the pallet, a gasket will be required. Also, the car owner is recommended to purchase an oil filter, but it is not necessary to change it at each fill of the transmission fluid.

The procedure for replacing oil in the gearbox on Chevrolet Cruz

In order to change the transmission oil with your own hands, you must refer to the instruction that is shown below.

Heat the oil in the gearbox before it is replaced. To do this, it is necessary to pre-pass by car 5 km.
Locate the car on a flat surface. The oil change can be replaced on the overpass, pit, but the most convenient to produce work with the help of the lift.
Remove protective casing power plant. To do this, you need to unscrew four mounts using a ratchet or "15".
Substitute a precipitated capacity under the drain bolt.

Using the key or ratchet, unscrew the drain bolt from the pallet.

Merge oil into a substituted container.
Unscrew the bay hole. This will allow oil to merge faster.

For more complete drain oil, the car owner can remove the pallet when the old transmission fluid is no longer flowing from the hole.
The pallet removed must be cleaned from the residues of the old lubricant.
If necessary, replace the oil filter.
Using a new gasket set the pallet.
Split drain plug in its landing place.

For orientation in quantity necessary oil It is recommended to measure the merged alive.

Unscrew the cork of the test hole.

Using a funnel to pour fresh transmission fluid.

Wait when the oil flows out of the control opening. After you spin the plug.

Close the bay hole.
Warm box.
Check the level of transmission fluid in the automatic transmission.

Automatic gearbox - unit that cannot work normally without lubrication. The presence of lubricant material in the checkpoint allows you to function correctly to all nodes and mechanisms, so the liquid replacement is relevant to all car owners. How oil replaced in Chevrolet Cruz automatic transmission and what needs to be considered, we will tell in this article.

[Hide]

How often does the replacement of ATF fluid?

First, let's look at when it is necessary to replace the liquid in the automatic transmission of Chevrolet Cruz. According to official data specified in technical documentation To the car, the replacement frequency is 75 thousand mileage kilometers. In the service manual, the manufacturer said that when visiting the maintenance station for performing that, and this is every 15 thousand km, the driver must make sure the absence of leaks and errors in the operation of automatic transmission. It is necessary to check the lubricant level in the system. This is exactly the vehicles that use automatic transmission with six gears and the Hydra-Matic 6T30 index.

Preparation for work

Before replacing the oil in Chevrolet automatic transmission, it is important to prepare correctly for the process. It is necessary to prepare a tool that may be required, as well as purchase a lubricant and a filter suitable for the aggregate. And then proceed to replace.

Tools and materials

Basic tools and materials that will need:

new oil - you will need 5-6 liters of fluid;
set of wrenches;
a basin or bucket where the work will be collected;
watering can either the bay funnel;
rags.

Which oil need to pour?

The most important nuance in preparation is to choose the lubricant you will pour. Initially, the manufacturer pours in the Chevrolet automatic transmission circle DEXTRON GM VI. Therefore, it is desirable to use the same oil.

Buying liquid, note that you can pour into a gearbox only with a lubricant for automatic transmission: the canister label will indicate the GM, ATF marking on the label.

Original oil from General Motors for automatic transmission

How to choose a filter?

Change oil filter for automatic box transmissions Chevrolet Cruze is not easy. The filter element is under the transmission lid, at the top of the gearbox. And in order to change it, you need to fully disassemble the unit. It is not easy, especially if you consider that in the cruises a complex gearbox is installed. In order to prevent the filter element, every 80,000 mileage kilometers can be changed. The need to replace the filter will occur when jolts and jerks appear when switching speeds during movement.

How to change the oil on the automatic transmission with your own hands?

Now about how to replace fluid in automatic transmission with your own hands. Before changing the lubricant in the "Automatic", it is checked. If the replacement is not planned, it is enough to perform a plot consumables.

Level control and advocate

To check the lubrication level in the unit, the Sapun in the gearbox closes. The power unit is started, while it is necessary to keep the leg on the brake pedal:

Switch the automatic transmission selector to D Mode
Wait about ten seconds.
Turn on the lever the next mode and so all the programs ascending. The procedure is repeated several times, and it is necessary to activate and rear transmission. At the very end, not drowning car Engine and turning on the mode neutral transmission or parking, unscrew the control plug. It is located right on the unit.

Read more about the diagnosis of automatic transmission, you can learn from the video published below (Author - Channel Chevrolet Cruze).

If a little merged lubricantThe control plug is twisted and the liquid topping is performed. It is about 0.5-0.7 liters of oil. If the lubricant did not come out of the control hole at all, then a top of one liter of fluid is made, before which the cork should also be tied. After that, the diagnosis is performed once again in the same way. Please note the oil that you will use to add before you preheat.

Oil replacement algorithm

Change and fill of the consumable material in the automatic transmission machine Chevrolet Cruise 2012 is performed like this:

The vehicle must be placed on a flat surface. Works are made on the overpass or in the garage with the pit. Even better if you have the ability to drive the car on the lift. This will ensure optimal access to the gearbox.
Under the drain hole of the unit, you need to substitute a basin or bucket - a waste consumable will be merged into the container.
The plum stop should be unscrewed and wait until all the lubricant comes from the transmission.
The bay of lubricant must be performed through the control hole. If the gearbox is equipped with a dipstick for checking, then determine the level of the lubricant simply.
After adding fluid to the gearbox, you must check the quality of the work performed. To do this, make a power unit, and the ACAP lever is alternately in each position. In the absence of difficulties in switching speeds, set the selector to the parking lot and give a motor to work for about five minutes.

1. Revealing the cork on the gearbox 2. Pouring the consumable material into the unit

If a vehicle Equipped with a temperature controller of transmission fluid, it is recommended to check the sensor readings. Then test the operation of the gearbox while driving. When switching should not be jerks and jolts. If the transmission works correctly, everything switches smoothly.

How much do you need to pour?

Separately, you need to say how much you need to pour lubricants to the unit. As for the volume, it will require approximately 8 liters of lubrication to fully replace fluid in the unit. However, it is impossible to complete the full replacement without dismantling and parsing the box. Therefore, on average, car owners spend about 5-6 liters.

What if the automatic transmission CHEVROLET CRUZE without probe?

If the level gauge is missing, then when the liquid is replaced, it is necessary to focus on the filled cavity of the open opening. When you see that the oil is ready to flow out of the hole, it must be stopped.

More about the main faults characteristic of automatic transmissions Chevrolet cars, as well as on the rules of operation of the automatic transmission, find out from the video (author - Shevi Plus TV).

How to configure the controller after replacement?

Controller setting is a mandatory step when changing the consumable material. The device must adjust the unit with a new viscosity. The configuration process is performed as follows:

Start the power unit of the car. Activate all transmissions on a parking box to neutral speed.
Wait a few seconds.
Set the gearbox lever to D mode.
Wait a few more seconds and return the selector to the neutral speed position. The procedure is repeated at least three times, which will allow you to train the controller.

In some cars in practice, everything works fine. But if something goes wrong, then jerk and jolts may appear when switching transmission modes, which will lead to noncomfortable car control as a whole. The process should be performed on the gearbox completely warm to maximum temperatures, since the controller is optimized to the temperature regime at which the training is performed.