Which oil to choose for the engine Skoda Rapid. Volume volume of oils and liquids SKODA RAPID SKM Checking the state of the engine oil

ŠKODA (Tiffanie) Paul, Hello! We clarify information on your question.

Pavel (Beverly) When?

ŠKODA (Tiffanie) Paul, good afternoon!

Pavel (Beverly) i.e. 504 tolerance will also go?

Pavel (Beverly) and in the channel documents indicated QG2

ŠKODA (Tiffanie) Paul, clarify information on your question.

Denis (Caine) Paul is most likely not, because 504 if I am not mistaken, for softer operating conditions, although in a Volkswagen for some reason, 504 is poured, and in Skoda 502

Pavel (Beverly) despite the fact that this engine Staven on both stamps. And immediately write no less than 502 tolerances. 504 is clearly not lower. In general, no specifics.

Sergey (Marah) is strange. And I am as official with Novy Lily Shell 5W30 AV-L. This oil has 504-507 tolerance. And I already drove 160000. I have been using this butter.

ŠKODA (Tiffanie) Paul, good afternoon! According to the manufacturer's recommendations, the engine oil is recommended for the engine of your car. concern Volkswagen. (VW 502.00). In the absence of ability to use the original engine oil, we recommend applying castrol oil With the corresponding tolerance and viscosity, for example 5W-40. Also selection of viscosity motor oil You can choose yourself, depending on the region of operation. Oil tolerance is specified on the package.

Denis (Caine) Paul, engine True different, albeit both 1.4 and 140 hp, but labeling are different

Sergey (Marah) 1.4 140l.s Lew Castrol 5/30, I'm currently thinking about Motul or Shell

Alexey (Annalise) Which oil pouring 1.4 140

ŠKODA (Tiffanie) Alexey, good afternoon!
For all gasoline engines serviced by the QG0 regulation (for Russia), the motor oil is used by the tolerance type not lower than VW 502 00.
These standards correspond to, for example, shell and Castrol brand oils recommended for use by the manufacturer:
Shell Helix Ultra 5W-40 - VW 502 00,
Castrol Magnatec. Professional B4 SAE 5W-40,
Castrol SLX Professional B4 SAE 5W-30
Castrol Edge Professional 5W-30

Alexey (Annalise) Thanks for the deployed answer

Almir (Gallvin) I have Skoda Rapid 2016 MG CWVB. Mileage 1000 km. It is necessary to add oil. Which oil flooded the manufacturer? Admission VW 502 00. And what is the viscosity of 5W40 or 5W30?

ŠKODA (Tiffanie) Almir, good afternoon! For all gasoline engines serviced by the QG0 regulation (for Russia), the motor oil is used by the tolerance type not lower than VW 502 00.
These standards correspond to, for example, shell and Castrol brand oils recommended for use by the manufacturer:
Shell Helix Ultra 5W-40 - VW 502 00,
CASTROL MAGNATEC PROFESSIONAL B4 SAE 5W-40,
Castrol SLX Professional B4 SAE 5W-30
Castrol Edge Professional 5W-30

Almir (Gallvin) that is, if there are 5W-40 and pour 5W-30 everything will be fine ???

ŠKODA (Tiffanie) Almir, good evening! We recommend to familiarize yourself with the instruction manual. Section "Specification and Filling Motor Oil". The manual indicates that when the topping can be mixed various oils together.

Tags: What oil pour into rapid 1.6 110 hp

Some Rapid owners note the increased JOR engine oil and evaporation of antifreeze. Today specials ...

MPI 1.6 engine 1.6 MPI 105l. from. On the Skoda Rapid, what are Kasalki in him and what is its advantages? | Topic author: Maxim

Konstantin engine is unpretentious, it may well work at 92 gasoline. It has a solid design, as the manufacturer itself assures, the minimum mileage without repair is 300,000 kilometers, timely replacement Oils and filters. Not expensive and not difficult repair, due to simple device. Due to the fact that fuel mixture Mixed in special inlets before entering cylinders, such engines have limited capabilities. inlet system. This affects the power and torque. They cannot be called "dynamic" and powerful. Most likely, they are designed for unhurried ride.

Yuri is a good atmospheric motor, chipped because of this bad, put on Jetta and polo like, who owns who owns, no one complains

Vera is the best engine from the Vugovskaya line, a simple atmospheric with a timing chain, the main minus he does not warm it up in winter, but is corrected by installing additional pump

Skoda Rapid - Budget Liftbek, built on the platform Skoda Fabia. last generation. This model is considered the most popular Skoda car in Russia - largely due to the affordable price, sports handling and quality materials. But like any mechanism, the car must be serviced in a timely manner. At first glance, it is problematic in the absence of a guarantee. But on the other hand, without self-service Do not work out. At least we are talking about elementary procedures that can perform each owner Skoda. Rapid - for example, pour new oil into the engine. But much more difficult to choose a suitable liquid, and this question is even the experienced Rapid owners. In this article, consider what you need to pay attention to when selecting high-quality engine oil for Skoda Rapid.

To get started to highlight the main motor gamma Skoda Rapid:

• 1.2 l, 105 liters from. petrol
• 1.4 l, 125 liters. from. petrol
• 1.6, 90 liters. s., Diesel
• 1.6, 90-110 liters. p., gasoline

Consider suitable engine oils for the indicated engines:

1. Total Quartz 9000 ENERGY 0W30 – synthetic oilHolding high wear resistance and cleansing properties. Such a liquid will protect the components of the motor in any weather, regardless of the driving manner and road quality. The product under consideration complies with international ACEA A3 / B4 standards, and also has the tolerance of VW 502.00 / 505.00. This oil Recommended for gasoline engines - both atmospheric and gasoline. High oil fluidity allows it to quickly penetrate even in the most difficult places in the engine. Total Quartz 9000 Energy 0W30 is perfectly adapted for low temperatures, and is suitable for the operation of the car all year round.
2. Total Quartz 9000 5W40 – this grease will be good choice for Skoda Rapid with petrol engines 1.6 and 1.4 liters. Lubrication complies with the standard VW 502.00, and refers to synthetic type oils. Due to its high thermal and oxidative stability, the Total Quartz 9000 5W40 product provides its properties throughout significant runs, up to the end of the car.
3. Total Quartz Ineo Long Life 5W30 - another optimal option For Skoda Rapid. This oil has the highest quality level, as it consists of ACEA C3 and VW 504.00 / 507.00 standards. This type of lubricant is designed for a long replacement interval, and thereby ensures convenience in operation. Sustainable oil properties retain their activity for tens of thousands of kilometers, prevent accumulation of deposits and metal chips inside the motor. The lubricant simply contains the minimum amount of ashiness, phosphorus and sulfur, and due to this there will be no problems with summer filter W. diesel engines 1.4 and 1.6 volume.

Video

The engine on the Skoda car over time is subjected to wear and deformation. To prevent this process, it is necessary to competently select engine lubricant according to tolerances and specifications from the manufacturer. High-quality oil will not only provide the functional performance of the system, but also protects it from damage.

What tolerances on Skoda different models

Skoda Rapid

Czech manufacturer Indicates a lubricant VW Long Life III Lubricant with a viscosity of 5W30 for Skoda Rapid models with capacity and volumes of engines:

• 122 hp TSI - 1.4 l;
• 86, 105 hp TSI - 1.2 l;
• 105 hp TDI - 1.6 liters.

For more powerful power units, the manufacturer recommends the VW Special Plus 5W40 oil. It is poured into atmospheric engines installed on rapid.

At factory B. new carThe conveyor released from the pipeline lubricant Volkswagen with tolerances 502 and 504. When performing, experts can offer auto-oil with other specifications and tolerances. For example, in Skoda service centers can offer oils from brands Shell, Mobile or Castrol.

Skoda Octavia

In the power units of Octavia A5, the manufacturer recommends pouring products on a synthetic basis. As for tolerances, they must comply with the standards of VW 502/504/505/507. Viscosity - 5W40, 5W30. However, when performing, the 0W30 lubricant is poured. Car enthusiasts prefer:

• Motul 8100;
• Castrol EJ;
• Shell Helix ultra;
• We are sitting about;
• X-wedge;
• Liquida moth.

• TDI 2.0 - 3.8 l;
• TDI 1.9 - 4.3 l;
• TSI 1.8 - 4.6 liters;
• TDI 1.6 - 3.8 l;
• MPI 1.6 - 4.5 liters;
• TSI 1.4 - 3.6 l;
• TSI 1.2 - 3.6 liters.

According to technical regulation, the oil change is carried out after 15 thousand km of mileage or earlier, depending on operational conditions.

Octavia 7.

In the instruction manual, it is indicated that for cars with a flexible replacement interval, it is necessary to pour oils with VW 504 tolerances if the engine has a volume of 1.2-1.4-1.8 liters and is equipped with a turbine.

In turbocharged engines with volumes of 1.6 and 2.0 per diesel fuel It is recommended to fill VW 507. If a limited interval is installed on the car, then lubricants with tolerances 502 are suitable for gasoline.

Czech manufacturer fills in cars by default Skoda Octavia. 7 Castrol EDGE 5W30 oil. It corresponds to the tolerances of Long Life III, which may be indicated on the canister together with specifications from Volkswagen.

After passing, the car enthusiasts prefer to change the branded lubricant on alternative analogs from manufacturers:

• Mobil;
• Shell;
• Motul.

The viscosity index is selected based on the operational conditions and temperature indicators of one or another region.

Speaking of replacement periodicity, it is necessary to proceed from the tolerances used. It is best to replace the car to achieve 10-15 thousand km of mileage.

Volumes of filling fluid in motors:

• TSI 1.2-1.4 - 4.2 l;
• TSI 1.8 - 5.2 liters;
• TDI 1.6-2.0 - 4.6 liters.

Oktavia tour

The replacement interval for OTC systems Octavia TUR is from 10 to 15 thousand km, depending on the operating conditions. The manufacturer recommends a synthetic-based lubricant with an index 5W30 or 5W40 depending on the parameters and volume of the engine.

The amount of oil poured is up to 5 liters. As for tolerances, the product must correspond to the VW 503-504. More than old versions of VW 501-502 may also be suitable.

Skoda Superb

Volkswagen Automotive Concern uses factory oil on a synthetic-based 5W30 for ICE systems Skoda Superb.. It corresponds to the tolerances of Long Life III VW. This almost the same lubricant as Castrol SLX. In the service centers in the motors pour lubricant on the synthetic database from the producer of the shell.

You can pour the car and from other manufacturers. The main indicator is the compliance of the tolerances of 502-504 and the viscosity classes of 5W40, 5W30. Also, do not forget about the periodicity of the oil replacement recommended for the engine systems equipped with turbocharging. If the superb model has 2.0 TDI engine, then it is better to use the 5W30 crawler with a tolerance of 507.

Lubrication with VW 504 tolerances must be used when running 15 thousand km. Some car enthusiasts prefer to replace the replacement after 10 thousand km. The regulation allows an earlier replacement if the car is operated in harsh climatic conditions.

Tolerance Skoda Yeti

For power units installed on Skoda Yeti.Fits the original grease GM DEXOS 2. It corresponds to the tolerances VW and LL. The packaging indicates the following tolerances:

• VW 504;
• VW 501;
• VW 502.

In service centers for atmospheric engineering systems of 1,6 MPI, operating on gasoline fuel, use Shell Helix or Edge Castrol with 5W30 viscosity indices. Such power units correspond to the tolerances VW 502/504/505/507. Experts also offer to fill motor lubricants From manufacturers:

• Motul 8100 5W40;
• Total 9000;
• Liquida moth.

Stopping at the choice special attention Specifications and viscosity should be given. As a rule, 4 liters are used for Skoda Yeti engines. Replacement is performed based on climatic conditions. Recommended frequency - 10-15 thousand km run.

Oil in the engine system Skoda Fabia

The engine fluid on the Skoda Fabia model must have a VW 502-505 tolerance and a 5W40 or 5W30 viscosity degree. Recommended Castrol EDGE.

You can also pour the compositions on a synthetic basis with the viscosity index of 0W30. In service centers, Skoda, specialists use such oil for Fabia with an engine capacity of 1.4.

Complexity

30 min - 1 h

Tool:

• Hex key for 10 mm
• Wrench Caiden Curved 18 mm
• Wrench for oil filter (VAS 3417 or analogs-puller 74 mm)
• Dynamometric Key

Details and consumables:

• Oil filter, Engines 1.2 MPI CGPC series (VAG 03D198819A)
• Oil filter, 1.6 MPI engines, 1.2 TSI and 1.4 TSI Series CFNA, CBZA, CBZB, CAXA (VAG 03c115561d / H)
• Oil filter, Engines 1.6 TDI CAYC series, CLNA (VAG 03L115562)
• Replacement oil, LongLife III (5W-30, 5W-40)
• Oil pallet tube, Engines 1.2 MPI CGPC series (VAG N0160276)
• Oil pallet tube, 1.6 MPI engines, 1.2 TSI and 1.4 TSI Series CFNA, CBZA, CBZB, CAXA (VAG N90813202)
• Oil Tube Tube Oil Pallet, Engines 1.2 MPI Series CGPC (VAG N0138492)
• Capacity (for draining waste oil)
• Rag

Notes:

The oil is selected in accordance with the standards of VW 50400 or 50700. Oil volumes for replacement:

• 1,6 Mpi - 3.8 liters
• 1,2 MPI - 2.8 liters
• 1.2 TSI - 3.9 liters
• 1.4 TSI - 3.6 liters

The photo material in the article can occur for different modifications engines. Replacing the Skoda Rapid filter, the procedure and approximate placement of nodes are similar in all embodiments.

1. Replacing the oil of Skoda Rapid begins with the fact that you need to unscrew the cork with an oil-sliced \u200b\u200bneck.

Note:

If the car is equipped with an engine crankcase protection, remove it to access the drain hole. The versions and location of the protection bolts may differ.

2. Submire the engine with a motor oil collection container. Unscrew the plug hole of the oil pan and drain the oil.

Note:

The oil is much better merged with a heated engine. But, in this case, be careful when unscrewed drain plugSo that hot oil does not hit the arms and other parts of the body.

3. Slightly verify oil filter The key and wait until it stops the oil from the filter.

4. After all the oil is fused, clean the carbouse of the oil drum, install a new sealing ring and tighten the torque with a torque of 35 nm. Depending on the configuration, the ring can only go with the plug. In this case, both details are replaced.

Tube of oil pallet VAG N90813202

Tube of oil pallet VAG N0160276

O-ring tube oil pallet VAG N0138492

Note:

The execution of crankcase traffic jams is sometimes different. They are both under the challenge and / or under the hex key. For alloy pallets, the effort of the plugs for a simple key, for steel pallets, plugs under TORX.

5. Before removing the filter, cover the rapid generator and the rest of the parts located. Remove the old oil filter completely.

A warning:

It is unacceptable to clean and re-apply a replaceable filter. With further handling of used filters and engine oil, it is necessary to comply with the relevant standards and rules for the oil economy and liquidation of exhaust oils and filters used!

6. Fill in oil, which is prepared for filling into the engine, the new oil filter is about a third of its volume. Grease the oil running in the set of a new oil filter sealing ring.

Oil filter VAG 03D198819A, Engines 1.2 MPI

Oil filter VAG 03C115561D / H, 1.6 MPI engines, 1.2 TSI and 1.4 TSI

Oil filter VAG 03L115562, Engines 1.6 TDI

7. Tighten the new oil filter. It is done by hand until a complete tightening or a special key-cup with a moment of 20 + 2.0 nm.

8. Fill the new oil into the engine and wait about 10 minutes.

Note:

Motor oil Skoda Rapid

9. Check and bring the oil level in the engine to the desired boundaries, as described in the article.

10. Let the engine. Check out the absence of oil leaks in any place. Oil pressure indicator lamp after 3 minutes should go out.

11. Turn off the ignition and after three minutes check the oil level again. If less than the norm is a fraction.

The article lacks:

• Photo of tool
• Quality photo repair

The Rapid model produced by the Czech company Skoda entered the market relatively recently. it inexpensive carwhich fully justifies its cost. The car attracts consumers with its appearance, high levels comfort, reliability and worthy technical characteristics Taking into account the price tag on such a car.

The car does not stand out with something bright, it is hard to call it unique. But with all its events, the machine provides good impressions from exploitation. "Rapid" inexpensive in service, many work allows you to perform yourself.

The car owner can change its own hands on the "Skoda Rapid" engine oil, without facing difficult or difficult to perform the stages of work. Designers have provided convenient access to drain and bay holes, with a filter replacement also does not arise any problems. This allows you to save money on a hundred service after the warranty period is completed.

Replacement frequency

"Skoda Rapid" is well adapted under russian conditions operation. But this does not allow in most cases to replace consumables with the frequency, which is indicated in the official manual to the car.

The manufacturer believes that during moderate operation in the engine is allowed to change the oil every 15,000 mileage kilometers. In practice, real numbers differ from the specified.

Reducing the period between the term is due to several factors:

• late oil tank;
• refueling at low-quality gas stations;
• bad condition of the road;
• sharp temperature differences;
• climate;
• aggressive driving style;
• excess recommended movement speed;
• regular ride under load (filled trunk or trailer);
• the use of low-quality consumables and spare parts, etc.

There are many reasons that can adversely affect the condition of the oil in the motor and the loss of its physicochemical properties. Because the route "Rapid" is obliged to regularly check the level and condition motor fluid, to pour it in a timely manner or completely.

According to the manual, the period between replacements is 15 thousand kilometers, but the actual gap is usually at level 8 - 12 thousand km. It all depends on the operating conditions and the relationship of the owner to its car.

Level and condition

To verify the current level or volume of oil in the crankcase, the standard oil Prope. It is located in the oil refining neck in the pumproom space.

It needs to be removed, wipe dry with a rare without a pile, return to the place and get it again. The probe remains a trail from the oil film in the area of \u200b\u200bthe minimum and maximum level marks ("Min" and "Max").

The task of the owner of the Skoda Rapid is to maintain oil at the level between two points on the dipstick. It says about, filled into the engine. When the level falls below the MIN mark, it is necessary to add to the carcase of the oil.

It also happens that in inexperience or chance is poured superfluous. Leave an excessive amount of lubrication is also impossible, otherwise there will be problems with the engine, leaks will begin. We'll have a part of the oil to merge from the crankcase.

To check the condition of the liquid, you can drain it from the crankcase if the time is approached for the planned, or use the same probe. Also, many use a syringe with a long hose, which is focused in the oil refining neck and remove a small amount of lubricant.

By appearance You can give an exemplary assessment of the current lubrication state. It is better to compare the sample with fresh similar oil. If the grease from the engine is dark, there are visible traces of soot, chips or dirt, it says about strong wear and necessity urgent substitute. Usually, the liquid becomes such after long-term operation without changing the lubricant.

In the engine of the Skoda Rapid car, the manufacturer recommends filling oils with tolerances 502 or 504. By class of viscosity, this corresponds to such options:

• 5w30;
• 5w40;

It is allowed to use only synthetic oil, because any mineral compositions or semi-synthetic do not even think.

When the machine works still on factory engine oil, it is important to know exactly what kind of working fluid is used there. It depends on the engine installed on the "Rapid".

A total of 2 oils from the manufacturer. These are fluids of the Volkswagen's own brand.

The first oil is called VW Longlife III and has a viscosity indicators of 5W30. It is poured into such engines:

• 1,4-liter gasoline TSI with a capacity of 122 horsepower;
• 1,2-liter gas engine TSI in two modifications at 86 and 105 horsepower;
• tDI engine with a volume of 1.6 liters and 105 horsepower.

The second version of the Special Plus lubrication with 5W40 viscosity parameters are poured from the factory to the following power units:

• 1,6-liter gasoline atmospheric engine with a capacity of 105 horsepower;
• 1,2-liter atmospheric at 75 horsepower.

The list of permissible producers whose products complies with the standards and requirements for engines "Skoda Rapid" includes:

• Shell;
• Castrol;
• KIXX;
• Motul;
• Valvoline;
• Mobil;
• Rosneft;
• LUKOIL, etc.

Skoda company gives a rather greater freedom of choice, because under the engines installed on Rapid, many compositions are suitable from different manufacturers.

But to save on a motor lubricant is urgently not recommended, since the characteristics declared by the manufacturer and physico-chemical properties may not be trite not true. This will result in a reduction in the period between shift working fluid, failure of nodes and more serious breakdowns of power units.

Tools and materials

To independently hold the "Skoda Rapid" procedure, you must first collect the necessary materials and a small set of tools.

Czech automaker does not impose increased requirements for the skills of people serving their cars in garage conditions. The design is pretty simple and understandable, which allows without unnecessary problems with their own hands to change the oil and other consumables.

From the tools you will need to take:

These materials and consumables include:

• new oil filter in accordance with the installed engine;
• new oil;
• a new plug of the drain hole;
• drain plug seal;
• empty container for draining old lubricant;
• rag;
• individual protection means not to burn hot oil.

As you do the work, you may encounter additional tasks, because the list of tools and materials can expand.

Number of oil poured

Before buying oil, you need to decide not only with its characteristics, but also with the required volume. Considering how much "Skoda Rapid", you will be able to accurately purchase the desired amount of fluid for replacement and talling between the service.

Additionally, take into account the need to flushing the engine with an oil. For this, special additives experts are not advised, because after their use, they partially remain in the system, react with lubrication and can provoke undesirable phenomena.

Optimally flushing the motor by the oil that you pour into the engine when changing the working fluid. The only negative is that this procedure will have to spend more money, as you need to buy more lubrication.

The refueling volume is directly related to the power unit installed on Rapid:

• 1,2-liter mPI motors 2.8 liters of lubricant require;
• in 1,2-liter variation, TSI needs to fill 3.9 liters;
• motor TSI 1.4 liters need 3.6 liters. motor oil;
• an ordinary atmospheric 1,4-liter engine needs a 3.2 liter of working fluid;
• if under the hood is 1.6-liter MPI, prepare at least 3.8 liters of fluid;
• 1.6 tdi poured 4.3 liters;
• the modern 1.8-liter TSI engine implies 4.6 liter oil fill.

Take a look at the technical specifications of your "Skoda Rapid" to find out exactly what type power aggregate It is installed on it. This will facilitate the purchase of the right amount. In each motor, the volume of oil is different, because during the operation of the liftback or stationary "Skoda Rapid" need to have an idea of \u200b\u200bthe most meaningful numbersassociated with cars.

To change lubrication in the engine will be required looking YamaThe specified tool kit and some materials. There is nothing difficult in the work, but try to strictly observe installed recommendations And stick to the elementary security rules.

Replacement procedure

The change of working fluid in the "Skoda Rapid" engines is approximately the same, since the location of the nodes on each motor is almost identical. This is a universal guide, suitable for the owners of the Czech car, regardless of the power unit installed on it.

Try to follow the instructions, rely on the official "Rapid" operating manual. If you have any problems, it is better to seek help from specialists.

1. First warm the motor up operating temperature. This will give oil the necessary fluidity. Mock the engine, open the hood and unscrew the oil-tank neck. It is usually located on the left.
2. Go under the car. On some machines there is a crankcase protection that you want to unscrew. This will open access to the drain hole. If you have no protection, you can skip this item.
3. Under the pallet, install an empty container, where it will be disturbed. If you plan to reuse oils (the plum is carried out within the framework of some repair), then take the clean capacity.
   
4. Carefully unscrew the cork so that hot oil does not hit you on the skin. Temporarily leave the oil to drain, because this will take about 10 to 20 minutes exactly. While go to the oil filter.
5. On Rapides, the filter is installed in the rotor space in front of the engine itself. To dismantle it, use a special key. Scroll through it a bit, but do not remove completely. First, there must be tracks from the filter oil.
6. Meanwhile, all the oil should have come out of the crankcase. Return to the car, take a new cork or a new seal. Install the plug in place, after cleaning the landing socket from pollution. You need to delay a torque wrench by exposing a moment on 35 nm. Sometimes only the seal cannot be purchased, because it is sold along with the plug. This is an inexpensive detail.
7. Return to the filter. Around it, lay out the rags so that the oil does not fall on the engine nodes and the generator. Remove the filter completely. It is not subject to restoration, therefore, do not try to clean it. Just buy a new filter.
8. In the filter housing, fill some oil from the canister with a new lubricant. Fill out about 30% volume. The sealing ring is also lubricated with oil, after which the filter is installed on its legitimate place.
   
9. The filter is delayed manually. If the hand slides or removes it convenient to capture the case, take a key-cup and tighten the filter with a moment about 20 nm, but not more than 22 nm.
10. Through the oil refining neck, pour fresh lubricant into the engine. Wait 10 minutes until the whole liquid stalks. It is not necessary to pour on the whole volume, because some of the old lubricant still remains in the system, which does not allow you to add an all amount in accordance with the specifications of the motor. Otherwise you have to merge surplus.
    
11. Bring the level to the norm, then close the lid and run the motor. Make sure that anywhere does not leak. After about 2 - 3 minutes on dashboard The oil pressure sensor lamp should go out. When this happens, turn off the motor and wait 3 - 4 minutes. If the level fell, the absence of the missing amount of fluid.
12. If the machine has a big mileage and the engine is worn, then wash can be done. To do this, repeat the procedure for changing the oil 2 - 3 times, but with a frequency of 300 - 500 kilometers. Each time you can change the filter. This can be done at the first and last shift of the working fluid in the engine.

Procedure self-substitution Motor oil on cars "Skoda Rapid" can not be called complicated. Each stage is available even to beginners who do not have extensive experience in servicing machines with their own hands.

The main thing here is to stick general rules Safety, use strictly corresponding to the requirements of the oil producer and not to depart from instructions. If you do everything according to the recommendations, then the engine will work efficiently, effectively and easily takes the period between the change of consumables, including oil.