What oil to fill in Ford Focus 2. Recommended motor oil for Ford Focus. Oil selection Oil oil for use so as not to run into fake

For 20 years, Ford Focus has been retaining popularity, being an unpretentious and reliable car. To ensure reliable operation of its engine, it is necessary to apply motor oil, approved and recommended by the plant, or to upload a lubricant that has similar parameters.

Not only work depends on the correctness of this choice. power plant, but also the duration of the operation of the aggregate. In our rating review presented the best oils Self different manufacturers, the main parameters of which are optimally suitable for each specific engine Ford Focus (on the territory of Russia, the most common models with type motors Endura, Zetec-E, Duratec and Eco Boost (Fox) were obtained).

Best Synthetic Oils for Engine Ford Focus

Synthetic has the properties necessary for high-quality lubrication. modern engines, has a more reliable protection against oxidative processes and reacts little to a high operating temperature inside the motor. Also an important feature of this category lubricants is a long operational period, during which all the stated oil characteristics are preserved.

5 LUKOIL GENESIS ARMORTECH A5B5 5W-30

Best price category
Country Russia
The average price: 1 421 rubles.
Rating (2019): 4.6

The oil is created on a high-quality synthetic basis, reinforced whole set of highly active modern additives Duramax designed specifically for the ruler synthetic lubricants of this brand. As a result, the products have good lubricating properties, an antioxidant effect, does not fade even with extreme loads.

Practically none of the reviews has critical estimates of this oil. There is an affordable cost, efficiency of the motor, the lack of neoplasms in the oil system. Moreover, the existing deposits in the motor gently and gradually dissolve, and, without falling into the sediment, can be removed upon the next replacement of lubrication. As a result, the efficiency of the motor increases, the level of vibration and noise during operation without load is reduced.

4 Xenum OEM-Line Ford 913-D 5W30

Multi-level motor protection from wear
Country: Belgium
The average price: 2 888 rub.
Rating (2019): 4.8

High quality oil, low sulfate, sulfate, sulfur and phosphate inclusions, can be poured into diesel and gasoline engines car Ford Focus. With the appropriate admission. Provides minimal wrencies of friction pairs, the content of carboxylic acid esters (Esters) retains the oil film at high temperature loads, increases the operational cycle.

The reviews there are more economical operation of the motor, an excellent detergent effect, the engine launch in winter even with severe frosts does not cause difficulties. Complex selection of additives included in the engine xenum oils Increases the resource not only internal circulation, but also the exhaust system.

3 Mobil Super 3000 X1 Formula Fe 5W-30

Most popular oil. Best frost resistance
Country: Finland
Average price: 1 928 rub.
Rating (2019): 4.8

Worldwide Mobil motor oils have proven themselves as high-quality and reliable products. By purchasing this lubricant for the engine of its Ford Focus, the owners can get to the frank falsification, whose properties are able to spoil the engine even the tractor. In numerous reviews full of high marks performance characteristics Mobil SuperAnd only the lack of decency in some sellers spoils the overall picture.

In general, oil provides reliable work in the economy At any time of the year, winter is not something unusual for the product developed in Finland. It can be successfully used in the northern regions of the country, with more severe climatic conditions. In addition, the lubricant reliably protects the engine from overheating, does not form a naiga and stops the corrosion processes inside the engine. The integrated effect of this oil inevitably leads to an increase in the motor test.

2 Castrol Magnatec Professional E 5W-20

Good high-tech oil, providing a long service life of the engine with regular timely replacements. The molecular structure of lubrication provides the coating of parts, especially intensifying in places of high energies (points of contact of friction pairs) and preventing direct contact. Even at large intervals in the engine operation, the molecular structure holds the required amount of oil on the working surfaces and provides lubrication of parts until the oil pump will create a working pressure in the system.

Many owners of Ford Focus cars began to pour this oil from the first days of operation, and in their reviews there are full satisfaction with its properties and high-quality operation of the motor. In the process of use, there was no formation in the engine of any deposits and there is not even a hint of their appearance.

1 Ford Formula F 5W30

Original oil. Stable viscosity
Country: England
The average price: 1 785 rub.
Rating (2019): 4.9

Made specifically for Ford automotive products, provides optimal conditions for the engine operation at any loads. The base lubrication base is obtained by the conventional hydrocracking method and thanks to the multi-stage cleaning system, it is not inferior in terms of the synthetic characteristics obtained from the gas. The surface of the parts inside the motor is covered with a sturdy oil film that reduces friction preventing premature wear Engine.

In the reviews of the Ford Focus owners, the stability of the oil viscosity is positively estimated, good fluidity with severe frosts, while improving the power of the motor and fuel economy. A set of high-quality additives ensures the stability of the oil structure - with high temperatures And long loads it does not dilute. Also has a good detergent effect without creating any deposits in the engine.

Best semi-synthetic oil for Ford focus

The semi-synthetic is actually a synthesized oil, diluted in different proportions of mineral. Temperature durability of such an oil is lower than that of clean synthetics, but the rest of the lubricant is perfectly coping with its task. Use looks more preferable in engines with great wear, but you can pour into modern motors. It should not be forgotten that the interval between replacements in this case will be less.

4 Comma X-Flow Type F 5W-30

Best price in the category. Increases the resource of the engine
Country: England
The average price: 1 610 rub.
Rating (2019): England

The peculiarity of this lubricant is the presence of an exclusive PCFINEUM package, which provides an excellent detergent and anti-corrosion effect. Thanks to the atomic inclusion of pH and Zn metals, the best slip indicators have been achieved, significantly reduced wear of parts during operation.

Ford Focus Owners characterize butter as reliable protection For motor. The reviews there is an improvement in the DVS dynamics, noise reduction during engine operation without load, fuel economy. When operating in the northern regions, Comma X-Flow has proven itself, providing a light launch in frosts, exceeding the mark in -30 ° C.

3 Motul 6100 Save-Lite 5W20

High level of chemical stability
Country: France
The average price: 2 500 rubles.
Rating (2019): 4.8

Another oil with the recommendations of the Ford manufacturer deserves to become a member of our rating. There are only two drawbacks of this product - relatively high cost and the ability to purchase a motul 6100 under view. The latter simply obliges the owners of Ford Focus to be more educated when choosing a seller.

As for the cost, then against the background of how the engine is "rejoicing" with this oil, and with each subsequent replacement increasing its resource, the price looks quite justified. Low sulphate ash content, satisfactory washing and oxidative effect prevent the burnout of the lubricant at any loads. Chemical stability in high operating temperatures modern DVS Provides unsurpassed qualities and ensures reliable protection of the engine nodes.

2 LIQUI MOLY SPECIAL TEC F 5W-30

High level of detergent properties. Increased interval between replacements
Country: Germany
The average price: 3,675 rubles.
Rating (2019): 4.8

Butter of this brand does not need advertising - it is one of the leaders in the lubricant market asking high level Quality. Despite the fact that the base of this lubricant was created on a mineral basis, the deep distillation technology (hydrocracking) made it possible to achieve quality comparable to clean synthetics.

Special TEC has tolerance for use in Ford brand cars. The high alkaline oil indicator (10.3) does not leave the chance for corrosion and other oxidative processes inside the engine, prevents the formation of sediments and nagar. There is an increased operational period and stability of work in high-energy modern motorsthat is not entirely characteristic of lubricants of this category.

1 Ford Motorcraft SAE 5W30 Synthetic Blend

Best friction protection
Country: England
The average price: 1 729 rub.
Rating (2019): 4.9

Premium oil is created on a purest basis, which has passed a multi-step cleaning. Oil film is resistant to shift, oxidation and mechanical exposure. As a result, the phenomenal decline in friction, the increase in the power and resource of the engine. There is also a high level of detergent properties that support the purity of the lubricant system at the level of the new motor. To some extent, all these factors provide fuel economy.

Many owners constantly pour this oil into Ford Focus, especially since it is designed just for cars of this manufacturer. Lubricant has proven itself in completely different conditions of work. Available positive reviews From drivers who have been successfully used by Ford Motorcraft in the conditions of northern regions, rural areas (in off-road), as well as in ordinary urban conditions. Everywhere the oil copes well with the loads, retains its properties throughout the entire period of work.

Dear experts read a lot of similar topics with a question about oil in ...

Auto Ford Focus 2, engine gasoline DURATEC HE 2L, MCPP, Mileage 153000km. I am geographically in the Rostov region, the temperature of the OCD. Wednesdays from -27 in winter to +40 in the shade in the summer. Riding 70% city without special traffic jams, the rest of the track with a different style of driving from calm to aggressive, but the engine turnover never raise above 4500-5000 boom / min under overtaking.

Luya always 95th gasoline on TNK and Rosneft. I change the oil through 10000km. I'm the 3rd owner of the car, the previous owner of Lil Castrol 5W30, the periodicity of the replacement was exactly at least 15000km. On the recommendation of the manual pouring 5w30, and is also allowed 5W40 or 10W40, but the fuel consumption and emissions will be increased. Recently, the dealer is filled with catastrophe 5W20.

Dear experts read a lot of similar topics with the question about the oil in the same car, but why did you decide to open a new topic. After buying a car (the mileage was 120,000) I was the cast of 5W30. Changed the oil through 10kkm. Curved forums about his tendency to Nagara formation, changed the brand of oil and began to follow Zhor, because this disease of the DURATEC family engines, but only with a volume of 1.8 and 2l.

Oil consumption at 1000km was about 200-220. Then, stumbled upon the network for the statement that an unofficial recommendation for the dealership service of oil with an index 5W40 instead of 5W30 in engines with a mileage with a mileage of more than 120km was supposed to be published from FMK. Outcasting the oil-free wheels with each oil change. Oil consumption fell to 170g / 1000km. Then due to the lack of at reasonable prices 1l the canister of this oil on the plot (they do not like our stores Lukoil
To take on the implementation, and refueling LUKOIL, by the way, too), had to change to a more affordable Mobil 5W40. Further, I read that the DURATEC engine has a very narrow tubing of the lubricant system and only 5W30 or 5W20 oil is suitable for it.

I understand that Mascinal is not good (the first sign of the overhaul) Motorists advise pouring 5W40 to reduce the wholesale, but I began to wake, but it is better to add oil to me just more often, and not having an oil starvation if it is present. In addition to the massembly of other problems in the engine, did not observe, it was normal in frosts. Watched here in fak for novice video about cold launch And about the runoff different species Oils - alerted. I compiled a comparative plate with the characteristics of oils Castrol with various indices, but decided to ask people, the dog here was eating:
1.

Is the statement about the use of more dense oils in engines with a mileage of more than 150kkm? 2. If we compare the oils of one manufacturer, the oil with which index is better pouring for operation in winter and summer in my region and with the condition of the wear resistance of the engine parts? I mean: 0W20; 0W30; 0W40; 5W20; 5W30; 5W40. 3. Does it make sense to go to 0W2040? four.

What is the advantage of 5W20 in comparison with 5W30? Judging by the table data, in 5W20 below kinematic viscosity at 40 and 100`s, as well as dynamic at -30`c. At 150`C, the castrol does not give data. 5. Advise some good anti-wear oils, taking into account the above issues. Sorry for many letters and do not kick much about stupid questions, but I wanted to write more in more detail, so that you understand my Logic torment to the oils of different viscosity. Thank you in advance for understandable answers.

The engine is the heart of the car. Therefore, care for it should be thrift and timely. Monitor oil in the engine - one of the paramounts. Many do not know which oil is better pouring and replacing the oil on the service: it's easier, more reliable, although more expensive. But it is not at all the fact that you will change it to high-quality, although Schurdogoga demand. Therefore, this procedure must be monitored, and for this it is necessary to understand some details and nuances.

Main nuances when choosing a motor oil for Ford Focus 2

Mark Car Ford in Russia is one of the most beloved. This can be seen at least from the fact that one of the most sought-after goods for Ford Focus 2 cars, there is a motor oil. And his shift is one of the most ordered procedures on car services. In order for the engine to work in normal mode, it is necessary to regularly change or add it. This procedure should be done then and so, as the manufacturer Ford Focus 2. Otherwise, you can encounter problems with the engine. What exactly to pour into the engine will try to figure out.

Modifications of oils

From the Ford Conveyor Focus 2 comes with half-synthetic Motor oil Ford Formula F. To the first maintenance, it is not recommended to touch it or pouring a new one. This is due to the fact that in native oil there are special additives to adapt the motor to work. Therefore, while your car does not spend the resource specified by the manufacturer, the "Blood System" Ford Focus 2 is better not to touch.

But still the time will come when such a procedure will have to do. The first time it is better to do on the official service of the Ford Concern. But if you decide to do it yourself, then adhere to the basic rules.

For the correct answer to the question: "What is better to upload?" We must figure out in some details.

Engine oil affects:

1. Engine resources.
2. Efficiency of the car.
3. Dynamics of overclocking.
4. Catalyst resources.

Therefore, it is very important to choose exactly what will fit and protect your car's engine. It is also important to choose an option with additives, it will help to use the potential of Ford Focus 2 to the fullest.

Producers offer manufacturers for cars

In most of the manufacturers offer only a pair of types of such substances. Types of oils are different:

• viscosity (B. international format viscosity is indicated by SAE);
• operating properties (ACEA).

Therefore, choosing engine oil for the car, you must consider the manufacturer's recommendations.

Why is it important?

If you ignore and not consider the requirements of the Ford Focus 2 manufacturer, you risk, because it will lead to a tangible reduction in the engine resource.

How not to make a mistake?

The answer is extremely simple - stick to the labeling. That is, simplify the task when choosing an oil for the focus 2 brand will help tolerance of the car manufacturer. It is simple and convenient. You just need to compare the tolerance numbers in the Ford Focus 2 instructions with numbers specified on the package. Only in this case, you can be sure that your engine is optimally "adopted" lubricant.

When changing oil

Ford Focus 2 manufacturers recommend changing the circulatory system of the car once a year or after 20,000 mileage kilometers. Only three months passed, and the speedometer shows that your Ford Focus 2 ran 20 thousand - it is necessary to pour new liquid. Or has passed a year, and you drove only 5 thousand km - it's all the time to change it. But if you often ride around the city, that is, in places where a lot of dust, motorists are recommended to pouring new engine oil into the engine after 10 thousand runs.

Classification of oils

Motor oil is three types.

1. Mineral.
2. Semi-synthetic.
3. Synthetic.

By asking how to choose which of them for Ford Focus 2, first of all, you need to be guided by the recommendations of the manufacturer's company. For Ford Focus 2 you need to take three types.

1. Winter oil.
2. Summer option.
3. All-season.

Winter option is made to designate the Latin letter W. The letter is preceded by a number. All-season I. summer options Denote by numbers only.

Which oil to choose

Market car oils Very wide. Therefore, the unequivocal answer is problematic. But most of the motorists and services of services converge on the fact that it is better to take a completely synthetic option. The fact is that at the factory in Ford Focus 2 poured it. It has the most optimal viscosity and the necessary additives for normal engine operation.

Winter:

• such an option for Ford Focus 2 will provide easy engine launch in frost;
• due to the fact that it remains liquid in the cold state, the starter and smaller load is performed;
• due to its high yield strength, it quickly applies to all parts and minimizes the "dry" engine friction;
• motor is faster heated to operating temperatureAnd the car earlier is ready for movement.

Summer period:

• synthetic engine oil on a hot season does not lose lubricants;
• does not allow engine overheating.

Oil manufacturers

We considered above general conceptsWhich oil in Ford Focus 2 pouring. Now consider the main manufacturers of engine oils. The certification of the Ford concern falls a variety of manufacturers of engine oils. It is necessary to navigate the price-quality ratio. Consider the main and most sought-after manufacturers.

Castrol

Castrol - a favorite version of almost all European motorists. French car manufacturers use only Castrol. Products from Castrol High-quality and complaints from users. The manufacturer raised a high quality bar and follows not to lose its brand. Recently, Castol has released new EDGE engine oil. If you listen to reviews, it can be argued that this product can be pouring in the Ford engine focus 2.

Mobile 1.

In the past 10 years, the one who really cared about his car, pour something else to Ford Focus 2, except for Mobile considered mockery over the iron horse. At the moment, Mobile 1 also firmly keeps leadership in the engine oil market. Mobile products have many additives. They have a beneficial effect on the heart of Ford Focus 2, especially on the track. He shows the fact that it was Mobile most often formed. Therefore, when choosing a mobile, be alert. On the recommendations, for Ford Focus 2 almost perfectly suitable oil mobile 1 rally formula 5W-40, but it is expensive.

Modification Oils for Ford Car

After departing from the Ford Focus conveyor or Ford Focus 2, the half-synthetic Motor oil Ford Formula F is flooded in. Oil change is not recommended to the manufacturer to first then, since there are already special additives in the lubricant for normal adaptation of the power unit.

If the car service takes place in the car service, then there is no concern that the oil that does not match the type of engine will be flooded, be it Ford Fusion or Ford transit diesel. In the case of self-replacement of the "circulatory system", a series should be observed simple rules. Motor oils must match the Ford WSS-M2C913-A and FORD WSS-M2C913-B specification.

For example, filled into Ford Focus or Ford Mondeo factory ford oil Formula E 5W-30 can be replaced, and without compulsory procedures for washing the system, on the oil of the newest generation Ford. Formula F 5W-30, which is poured into Ford Focus 2 power units 2 and Ford Mondeo 4. change oil filter It is also not required.

Properly selected oil affects 4 main engine indicators:

• catalyst resource;
• dynamics of overclocking;
• motor resource;
• efficiency of the power unit.

Under the certification of the Ford company there is a sufficient number of manufacturers of motor oils so that you can make a choice between the optimal price-quality ratio. The most expensive option for Ford Focus 2 will be shell oil 5W-40. It significantly improves the start of the cold engine. If the price question is not principled, then this is what is needed for the Russian winter.

The average price segment will take oil from Castrol 10W-40. The qualities of this product are positively evaluated both professionals and motorists. New ruler EDGE raises the quality bar to an even higher level. Budget option For Ford Focus 2 will be the oil from Mobil 1. Additives contained in mobil oil 1 Rally Formula 5W-40, perfectly retain the engine from Nagara and give a light start in frosty weather.

The choice is always there, and it pleases. The price range is wide enough. And its lower limit is not limited only by the represented stamps. For the Ford Focus 2 engine, the 5W-40 ratio is perfect. And theoretically you can find the manufacturer of such an oil and at a lower price. However, it is worth remembering that the quality of the oil is the key to the long and uninterrupted operation of the power unit of your vehicle.

Features of oil replacement

To comply with the conditions of warranty, the first 3-4 years maintenance of all Ford models: Ford Fusion, Ford Mondeo 4 and even diesel ford transit occurs in service centers. The replacement of Ford oil is made on each of the qualified professionals. In the future, to save auto maintenance, you can change the lubricating fluid of the power unit yourself.

The characteristic distinctive features of this technological process is a bit. With strict execution of the sequence of steps even independent replacement Without the presence of appropriate experience, it will be easy and productive.

1. Preparatory work includes arrangement of the place of replacement, whether it is a garage, an overpass or looking Yama, and the preparation of a container for collecting waste fluid (5-6 liters).
2. The car is fixed manual brake When replacing on an uneven surface, using a boogan and jacks. You must additionally pave the wheels with bricks, since the safety of the work should be above all.
3. Open the oil cover of the engine.
4. We dismantle the protection of the crankcase. Complete set of Ford Mondeo 4, for example, has 5 bolted mounts.
5. We unscrew 2 bolts of 17 mm from below and 3 to 13 mm front mount.
6. Gently remove the nuts cooked with the plates, through the oval holes on the crankcase.

1. Remove Carter to the side. Care should be taken here, since the engine and oil inside it can have a temperature above 40 degrees, which, when contacting the skin, will cause burns.
2. Weakening the plug plug.
3. We set the pallet under it and completely turn away.
4. We are waiting until the oil is completely soles.
5. Outlook the oil filter. It is worth the caution, it may be there an oil residue.
6. Once all the oil is fused, install the plug back, without forgetting to change the sealing ring.
7. Before installing the new filter, it is necessary to lubricate its sealing ring with new oil.
8. Screw must be screwed until the sealing ring is touched by the cylinder block, then we make another turnover, maximum ¾.
9. Now oil replaced, 3-3.5 liters.
10. We close the oil cover of the engine.
11. We carry out a trial start and check all the nodes for leakage.
12. The moach motor and once again check the fluid level.
13. Install the Carter in the reverse sequence.

Saving funds when complying with the described sequence of oil replacement stages will be from 1000 to 2000 rubles.

Replacing oil in diesel engine

Unlike Ford Fusion, which comes in the Russian Federation only with a gasoline power unit, Ford oil transit diesel will be completely different. Ford transit diesel Oil pump is located directly on the front plate of the engine. The main problem is that fuel in Europe is very different in quality when compared, for example, with fuel from the Russian Federation.

For gasoline cars, such as Ford Fusion, it is less relevant. The percentage of sulfur in a stuff varies multiple. In the EU countries, the permissible norm is 300-400 units, and in Russia it is about 6500. The cetane number 55, compared with 48, strongly increases the engine wear, and correctly selected lubricant in such a situation plays the last role.

Ford manufacturers are recommended for diesel units with a small alkaline indicator (TBN). This rule works well in European countries, but when the motor is working at the temperatures of the Russian winter and with the quality of domestic fuel, the engine wear is 1.5-2 times. Industrial tests also showed an oil efficiency with a higher alkaline number to work in conjunction with the sulfur-containing fuel.

Here is an enlarged stroke reserve before changing, and the preservation of all properties of additives throughout the work, as well as the detergent effect. When choosing between universal and diesel oil Do not even think. Ford tests at the landfill in Turkey gave a clear result. For the Russian climate, it is worth considering the work in the winter when warming up in winter, as well as the launch of cold, up to -35 ° C, engine.

The results of the studies can be partially transferred to gasoline engines. And for refueling Ford Focus 2, taking into account weather conditions, use oil with a higher alkaline number. Otherwise, it is easy to increase the interval between fluid replacements.

By bringing all the information reviewed, let's point point at key moments. After purchasing Ford Focus 2 or any other Ford car brand to replace the oil worth not earlier than the first technical inspection. The factory liquid in the power unit already contains the entire necessary complex of additives that allow the engine to start a full adaptation to the loads.

If you need to change the engine oil, compliance with Ford WSS-M2C913-A and Ford WSS-M2C913-B standards is required if the resource and quality of the engine operation are prioritized. Main trade stamps for use in Ford Motors - Formula F from Ford, Castrol Magnatec., Mobil Super 3000, Mobil 1 x1, Motul 8100 Eco-Nergy, Xenum VX and VXR.

An independent replacement is not as complicated, as it seems. In the absence of a mandatory warranty service in dealer Center or the expiration of the guarantee of the independent replacement will significantly save the budget. Even Ford oil transit diesel can be replaced independently. If there is in the garage a passenger car Fore Follow the step-by-step instructions described above.

Due to the poor quality of diesel fuel russian production, oils for diesel units should be selected with a high alkaline number (TBN). This will increase the resource of the power plant and the frequency of replacement of the lubricating fluid. Good luck on the roads!

Ford Focus of the second generation is one of the most common budget cars in Russia. Despite the fact that the second generation is not produced for a long time, these models are still often found on the streets of cities. The car has proven itself from a good side. This is a reliable and economical car for every day. But that the operation does not have a burden, it is necessary to regularly produce maintenance. One of these operations is to replace the oil on Ford Focus 2. But the replacement is just half an end. In order, the engine served for a long time, you need to know which oil is suitable for a particular power unit. Well, let's deal with what oil is better for the Ford Focus of the 2nd generation.

What are pouring from the plant?

On the focus conveyor walked with semi-synthetic oilwhich corresponded to the tolerance of Ford WSS-M2C913-a. As for the brand, it was the product "Formula F" with a viscosity of 5W30.

This oil has a whole complex of additives that are so necessary when running a new power unit. But the time does not stand still, and now the second "tricks" are no longer produced. So what oil for Ford Focus 2 (1.8) will be the best? There are a lot of options.

MotorKraft Full Synthetic (USA)

Owners of diesel "focus" note: Suitable "MotorCraft Full Synthetic" only for gasoline engines.

"Castrol"

This is already european Mark.. All French cars go on this oil, and it is not contraindicated for "focus". Judging by the reviews, the products from "Castrol" features high quality and detergent properties. This is especially noticeable on engines with mileage for 200 thousand. The product perfectly flips all dirt and accumulated deposits. Among the disadvantages reviews are noted more high cost. The product price is 5.5 thousand per five liters. American "Motor Kraft" costs 30 percent cheaper. Also on MotorCraft make less fakes.

But the counterfeit "Castrol" in the domestic market is enough with his head - they say motorists. When buying, you need to carefully look at the inscriptions and not buy canisters with incorrect fonts and curve dimensional lines. What kind of oil for "Ford Focus" of the 2nd generation pouring? If we consider the "Castrol" line, then experts recommend using the EJ line with a viscosity of 5W40. This is a pure synthetics, but also have semi-synthetic. This is "Castrol Motogany" 5W30. As practice shows, it is not worse than the previous one - the same wash the dirt and does not hush it in winter.

Other options

Are there any analogues? Their mass, but most use the following products:

• "Motul" 913c. This is a semi-synthetic product with a viscosity of 5W30. One of the most cheapest listed. The cost of five-liter canister is 2.5 thousand rubles.
• Shell. One of the advantages is that the oil is suitable for any season. With him the car perfectly feels like in the winter and summer.
• "JB Jerman Oil Ll hopped." This is a synthetic oil. Sold in four-liter canices. Cost - from 2.5 to 3 thousand rubles. There are options for both gasoline and for diesel engines.

How much to fill?

Along with the choice of brand, motorists are wondering the amount of lubrication. Since "focus" was established different engines, the volume of the product fillible will be different. Let's start with the smallest motors. These are 16-valve aggregates 1.4 with gasoline injection. It is recommended to use 3.75 liters of oil. The same digit and in 1,6-liter diesel engines. But the gasoline 1,6-liter aggregates of Duratek need more oil. For replacement, 4.1 liters of product will be required. The 1.8 engine is designed for 4.25 liters. For two-liter engines With gasoline nutrition, it is recommended to use 4.3 liters of oil. But in the turbodiel engine 2.0 it is already pouring already 5.5 liters.

What if it is not possible to measure the volume?

If the oil is poured right from the barrel, it is possible to determine the norm by Schu.

Specialists say that the level should be average or higher. But it is worth remembering that a lot of oil also harms the motor, like his absence. It is necessary to adhere to certain norms.

About transmissions

Along with the engine, you should not forget about the transmission. This is an equally important unit after DVS. The "Ford Focus" of the second generation was established both mechanical and automatic transmissions. Let's start with the first. On the manual transmission of oil from Ford Focus 2, every 75-90 thousand kilometers should be made. No more than 2.2 liters of oil poured into the box (although the full volume specified by the manufacturer is 2.8 liters). As for viscosity, the product 75W90 is usually chosen. Manufacturers can be different. The most popular - "Mobile Mobybalone 1". Despite the high viscosity, this product performed perfectly in the northern regions. Owners in reviews do not complain about the work of the transmission - in additional warming it does not need. The cost of the product is 800 rubles per liter, which is quite acceptable. Also, motorists use "Castrol". However, it costs more expensive - from 1.2 thousand rubles per liter. For quality, these two brands are identical, so there is no point in overpaying for the brand.

What else can oil in the box "Ford Focus 2" pour? For those who want to save yet, not to the detriment of quality, experts advise to consider Eneos Gear 75W90. However, the reviews say that the product is afraid of frosts. It follows only in a temperate climate, otherwise you can spoil the box. The boundary threshold of operation for Enios Gear is minus 20 degrees. What kind of oil love is for its price. One liter costs 375 rubles.

Replacing oil in automatic transmission on "Ford Focus 2"

Automatic transmission has a completely different principle of operation, so oil is different here and viscosity, and technical characteristics. Instead, ATP-liquid is used here. It can be recognized by characteristic red color. What product should be chosen? Specialists advise use original oil "Merkon V". How many liters will required? It all depends on the method of replacement:

• With a partial method of replacing the oil into the Ford Focus 2 automatic transmission, about five liters of fluid will leave. Usually this method is used by those who serve the car with their own hands.
• If hardware is used (i.e. full replacement), It is necessary to have at least ten liters.

The cost of the procedure, taking into account the work and materials, is 12 thousand rubles. When hardware replant, experts produce disassembly of the pallet, cleaning filters and magnets, as well as lubrication of fittings. Back the pallet is installed on the sealant (the old one is previously removed by the knife).

Upon completion of the operation, a jump is possible at idle. But after two or three minutes everything stabilizes is a normal phenomenon. By time, the hardware replacement takes no more than half an hour. A C. partial replacement You can give about three hours. Plus, everything in a thousand kilometers will again have to break the pallet and merge oil. When hardware replant, the following maintenance will be required only after 60 thousand kilometers. It is this figure that is the regulations for replacing ATP fluid into the "Focus" automatic transmission.

So, we found out how to choose oil for Ford Focus 2 into the engine and gearbox.